Name: DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart
Brand: Valvoline
SKU: 798153
Price: 11.99 USD

from

$11.99

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands of many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON*, DEXRON*-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$429.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Dana Spicer 80
11.25″ ring gear diameter
37 spline pinion
12 ring gear bolts
4.11 ratio
Thick gear for 3.73 and down carrier

from

$744.99

Differential Carrier

from

$15.99

Product Features:

Carrier shim kit for Dana Spicer 30 with 30 spline axles

from

$556.99

Product Features:

Each LuK GearBOX contains all the OE quality bearings needed for a professional transmission repair
LuK Differential Bearing Kits are designed to meet or exceed OEM requirements. This will ensure customer satisfaction.
LuK Differential Bearing Kits contain the bearings and seals needed to complete the job.
LuK Differential Bearing Kits include wear parts such as seals, O-rings, shaft sealing rings, support bearings and spare parts where necessary for eliminating the specific cause of failure.

from

$79.99

Product Features:

Pinion depth shim kit
Fits Dana Spicer 80 4.125″ design

from

$318.99

Product Features:

Spider gear kit
Fits Dana Spicer 80, 37 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$138.99

S135 ring gear bolt & nut kit (set of 16 bolts).

Product Features:

Ring gear bolt and nut kit
Fits Dana Spicer S135
Includes 12 bolts and nuts

from

$7.99

Dana 70 & Dana 80 pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer for Dana Spicer 70 and 80

from

$994.99

Differential

from

$5.99

Product Features:

Pinion nut washer
Fits Dana Spicer 80

from

$93.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

CARRIER BEARING KIT FRD 10.5″ W/TIM

from

$319.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$19.99

Product Features:

Oil baffle
Fits Dana Spicer 80

from

$198.99

NO RETURN HM807046 SET-UP Bearing (1 SINGLE Bearing) for Dana 80 , 11.5AAM , 4.125″ OD .

Product Features:

Set up bearing
Fits HM807046 pinion bearing
Easily slips on and off pinion journal to allow for pinion depth adjustment

from

$47.99

Plug adapter for extra-large clamshell. No Return.

Product Features:

Plug adapter for Extra Large clamshell
Fits carrier bearing puller

from

$502.99

Dana 80 TracLoc clutch set round design (remove 4 plates 4 V-Type).

Product Features:

Clutch kit
Fit Dana Spicer 80 Trac Loc positraction

from

$42.99

Pinion nut for Spicer S135 & S150.

Product Features:

Pinion nut
Fits Dana Spicer S135 and S150

from

$69.99

Dana 70 & Dana 80 standard Open cross pin shaft, one piece case.

Product Features:

Cross pin shaft
Fits Dana Spicer 70 and 80

from

$446.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers, thread locker, marking compound with brush and silicone.

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$311.99

Yukon replacement standard open spider gear kit for Dana 80 with 37 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Dana Spicer 80 open differential with 37 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$16.79

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$21.49

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features: