from

$13.99

High Energy Hydraulic Flat Lifter Chevrolet SBC, BBC, and 194-292/200-262 V6.

from

$49.99

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

Advance the cam for increased torque and horsepower
Tune your powerband for more end torque or increase top end horsepower
Includes (4) offset bushings and (1) 0 degree bushing
Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
Increase Top-End Horsepower

from

$457.99

Edelbrock #8827 Water Pump small block Chevy cartridge style race ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling

Product Features:

Standard Impeller Rotation
0.750 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.8125 in. Block To Hub Height
Satin Finish

from

$32.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$106.99

This Spectre engine dress-up kit was designed for the 1987 – 1995 Chevy 305 & 350 engines. This kit includes: stock height valve covers, chrome valve cover T-bolts, chrome oil filler cap, chrome PCV breather, grommets, and an air cleaner adapter stud. The air filter adapter stud, is a z-bolt that is designed to allow you to use a center stud style air cleaner assembly instead of the stock dual-stud setup. Manufactured using high quality materials this kit features triple chrome plated parts.

Product Features:

For 1987-1995 Chevrolet 305-350 engines
Includes stock height valve covers & T-bolts
Includes oil filler caps, pcv vent filter
Includes air cleaner Z-Stud
Chrome engine kit

from

$259.99

HYDRAULIC – Xtreme Energy: Good for street machines, slightly rough idle, stock converter will work but best with 1800+ stall.

Product Features:

HYDRAULIC – Xtreme Energy: Good for street machines, slightly rough idle, stock converter will work but best with 1800+ stall.
268/280 Advertised Duration, 224/230 Duration @ .050″, .515″/.520″ Lift, 110 Lobe Separation
Valve spring upgrade required
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$32.49

Secure the harmonic balancer or dampener on your Chevy. Works on original equipment, high performance street, drag or circle track applications. Features a heat treated black oxide coated Grade 8 alloy steel bolt for strength with a tall hex head to prevent wrench from slipping. An extra thick parallel ground washer provides accurate, uniform torque, and a lock washer is also included.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Tall hex head bolt to prevent wrench from slipping
Extra thick parallel ground washer provides accurate, uniform torque
Washers Provides More Accurate And Uniform Torque
Grade 8 Alloy Steel

from

$32.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Made From Cellulose/nitrile Composition Material
Provides Excellent Sealing And Durability
Can Be Trimmed If Necessary For Modified Port App

from

$35.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Application specific design to ensure a perfect fit
Meets or exceeds all original equipment specifications
Engineered and manufactured specifically for repair applications
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$17.79

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$10.99

10 Degree Superlock Steel Retainer for 1.250" OD Valve Spring

from

$342.99

BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Xtreme Energy: Strong torque. Excellent response, heavy towing in 454 with 4.10 gear.

Product Features:

Cam and lifter kit for Big Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Xtreme Energy: Strong torque. Excellent response, heavy towing in 454 with 4.10 gear.
262/270 Advertised Duration, 218/224 Duration @ .050″, .504″/.510″ Lift, 110 Lobe Separation
Valve spring upgrade required

from

$201.99

Edelbrock part #9653 Pushrods are designed for Chevy 348/409 “W” series V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precis

Product Features:

7.2 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$9.99

This is a high quality gasket that will seal that leaking water neck, and provide you with years of service. This gasket works well in all applications.

Product Features:

Made From Cellulose/Nitrile Composition
Provides Excellent Sealing And Durability
These Gaskets Are Die Cut For a Precision Fit
Fits Small Block Chevy V8 Engines 1955-’90
Fits Big Block Chevy V8 Engines 1965-’90
Fits Small Block Chrysler 318/360 1979-’92
Fits Small Block Chrysler 3.9L/5.2L/5.9L Magnum 1992-’03

from

$25.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$1080.00

Product Features:

Designed for 1987-95 Throttle Body Injection or Tuned Port Injection 5.7L Small-Block Chevy engines originally equipped with center bolt valve covers
Flat Tappet Camshaft Type
60cc chambers with 165cc intake ports
Size of intake valve is 2.02 in. and exhaust valve is 1.60 in.
Sold as one complete head

from

$159.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Non-Rotator Style: Dyno Tested and Street Proven
Great Match to Edelbrock Camshaft Kit

from

$77.99

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Grade 8 Steel

from

$57.99

Throttle linkage kit for street tunnel and victor ram. Use for forward mounted carburetors only.

Product Features:

Throttle Linkage Kit for Street Tunnel/Victor Ram
Use for Forward Mounted Carburetors Only

from

$562.99

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$27.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$20.79

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$10.99

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
3/8 inch-16 by 1 inch bolts
Kit includes 12 bolts and washers
Manufactured from high quality steel
Bolts feature hex heads

from

$35.99

If you are changing your camshaft or replacing the timing set, make sure to replace this seal at the same time! Made from Nitrile rubber.

Product Features: