Chevrolet Bel Air Differentials

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits GM 8.2″
• 3.08 ratio and up only
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits GM 8.2″
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

High-quality Differential Carrier Shim Kit

Product Features:

• CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

• Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
• 1/2″ head

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

• Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
• Left hand thread

RngPnnInstlKt

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

8.5, 9.5, & 8.2 Buick, Oldsmobile, Pontiac GM REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Pinion Redi-sleeve
• Fits GM 8.5″, 9.5″ and 8.2″ Buick, Oldsmobile and Pontiac

MiniSpool

Value-priced seal meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Polished aluminum cover for 12P GM.

Product Features:

• Fits GM 12 bolt passenger car
• Finned polished aluminum

Dana 44, GM55P & 8.2″ GM pinion gear Thrust washer.

Product Features:

• Pinion gear thrust washer for Dana Spicer 44, GM 8.2″ and 1955-1964 GM passenger car

Yukon yoke for GM 12 bolt car & truck, 1330 u/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 12 bolt passenger car and truck
• 30 spline
• 1330 u-joint size
• Outside snap ring design
• 3.625″ snap ring span
• 1.062″ cap diameter
• U-bolt style

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Ring gear bolt for GM 7.5″, 7.6″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ & 8.6″ IRS. 7/16″ x 20.

Product Features:

• Ring gear bolt for GM 7.5″, 7.625″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ and 8.6″ IRS
• 7/16″ x 20

Standard Open side gear thrust washer for 12P and 12T GM.

Product Features:

• Side gear thust washer for GM 12 bolt passenger car and truck
• Fits standard open differentials only

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (with Supershims).

Product Features:

• Fits GM 8.2″
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M86610 race
• All steel construction

10 bolt Mini Spool for 8.5″ GM with 28 spline axles. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 8.5″ with 28 spline axles
• Installs into a standard open carrier case
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

8.75″ Chrysler & 55P Chevy Power Lok clutches, Model 20 also, POSI.

Product Features:

• Clutch kit
• Fits Chrysler 8.75″, 1955-1964 GM passenger car and AMC Model 20 Powr Lok positraction

55P Chevy Passenger Drop Out gasket.

Product Features:

• Cover gasket
• Fits 1955-1964 GM passenger car

8″ Toyota, 7.5″ GM, 8.2″ GM, 12T, pinion shim set, & Mazda truck.

Product Features:

• Pinion depth shim kit for Toyota 7.5″, 8″ and V6

Product Features:

• Pinion depth shims for GM 7.5″, 7.625″, 7.6 IFS, 7.6 IRS, 7.75″, 8.2″, 1955-1964 passenger car and 12 bolt car and truck