Chevrolet Bel Air Air Intakes
Top Chevrolet Bel Air Air Intakes Categories
We carry over 220 Air Intakes in inventory for the Chevrolet Bel Air. If you’re looking for aftermarket Air Intakes for your Chevrolet Bel Air, check out all these categories:
Essential Chevrolet Bel Air Air Intakes
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$62.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)
from
$620.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Carburetor Accelerator Pump Diaphragm #12401 50cc (Part No.12401)
from
$31.99
Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Product Features:
See More
Product Features:
- Rubber Material
- For Holley®, Barry Grant, And Demon Gasoline Carburetors
- No Hardware Included
- 50cc Volume
- Made iIn The USA
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Main Jet Carburetor Metering Jet #12459 Size .058 (Pair) (Part No.12459)
from
$13.99
The Edelbrock 94 #12459 Carburetor Jets .059″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 59 Maximum Jet Size
- 0.058 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Felpro – Air Cleaner Mounting Gasket (Part No.11528)
from
$2.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Carquest – Carburetor Float (Part No.779-8067B)
from
$18.99
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
- Designed and manufactured to our stringent quality standards at a certified facility, so you can install with confidence
- Premium components and durable materials withstand harsh engine conditions to increase longevity and lifespan
- Undergoes extensive testing and validation for proper performance and peak reliability
- As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Pro-Flo 1000 Series Chrome Air Cleaner with Foam Element with 5-1/8" Air Horn (Part No.1002)
from
$31.99Product Features:
- Super Flow; Good Filtration
- Urethane Foam Element
- Strong Metal Inner Frame
- Performance Benefits
- Cleans With Soap and Water
- Low Maintenance Cost
- Simple To Install
- Nicely Finished; Low Profile
Felpro – Carburetor Mounting Gasket (Part No.60248)
from
$7.29
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Intake Manifold Gasket for 1958-65 348/409 "W-Series" Small Port (Part No.7242)
from
$27.99
Edelbrock part #7242 Intake Gaskets for 1958-1965 348/409 “W-Series”, Small Port Chevys allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP
Product Features:
See More
Product Features:
- 2.50″x1.31″
- Features Embossed Silicone Bead Around The Intake Ports & Water Openings
- .060″ Thick
- Two Piece Configuration
- End Seals Not Included
Holley – REPLACEMENT MAIN BODY KIT FOR 0-80457S (Part No.134-342)
from
$195.99
REPLACEMENT MAIN BODY KIT FOR 0-80457S
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$186.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$19.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$24.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1781)
from
$35.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Edelbrock – Throttle & Auto Trans Kickdown Bracket #8030 SBC 1995 and Earlier (Non-Vortec) (Part No.8030)
Edelbrock – Triple Carburetor Fuel Log Kit #1288 with 5-1/2 in. Outlet Spacing (Part No.1288)
from
$99.99
This Edelbrock Fuel Log kit #1284 is an exact replica of the original design used by Vic Sr. in the 1950’s. They are made from extruded aluminum tube with a 3/8″ threaded outlet at each end and a polished finish. Kit includes, black neoprene hose, Corbin
Product Features:
See More
Product Features:
- Polished Log
- Brass Fittings
- Black Neoprene Hose
- 5-1/2 in. Outlet Spacing
- Includes Hose Clamps
Felpro – Carburetor Mounting Gasket (Part No.60731)
from
$8.29
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$20.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Performer Air-Gap Intake Manifold for 1955-86 Small-Block Chevy, Polished Finish (Part No.26011)
from
$674.99Product Features:
- Based on Performer Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- Polished Finish Produces Brilliant Shine
- Ideal for Street Rods and Street Machines
Carquest – Carburetor Choke Pull-Off (Part No.779-043)
from
$31.05
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
- Designed and manufactured to our stringent quality standards at a certified facility, so you can install with confidence
- Premium components and durable materials withstand harsh engine conditions to increase longevity and lifespan
- Undergoes extensive testing and validation for proper performance and peak reliability
- As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process
Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)
from
$284.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More
Mr. Gasket – Intake Manifold Bolts (Part No.955G)
from
$15.49
These grade 5 socket head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8-16 x 1 inch bolts & washers.
Product Features:
See More
Product Features:
- Grade 5 socket head bolts are zinc plated for protection and appearance
- Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds
- Washers Included
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$13.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Chevrolet Bel Air Air Intakes Categories
Helping You Find the Right Air Intakes for Your Chevrolet Bel Air
You love your Bel Air. So we’ve made it easier than ever to help you find Chevrolet Bel Air Air Intakes in our online catalog. Our inventory holds 220 aftermarket and OEM Air Intakes for your Chevrolet Bel Air, ranging from $1.99 to $900.99.
We offer parts from 11 brands trusted to make quality Air Intakes for your Chevrolet Bel Air. Before you buy, take some time to read through customer reviews. We currently have 11,550 reviews of Chevrolet Bel Air Air Intakes from previous customers. Some of the top rated parts include Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny with 4.7 stars and Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) with 4.6 stars.
Find your Bel Air Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Chevrolet Bel Air part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Chevrolet Bel Air
Our inventory holds Air Intakes for your Chevrolet Bel Air from 11 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Edelbrock, and Mr. Gasket, all of which can keep that Chevrolet happy.
We have Felpro parts available for your Chevrolet Bel Air in categories like Air Cleaner Parts. Some of the top-rated Felpro parts in these categories are:
Top-Rated Felpro Air Intakes
Leading Felpro Air Intakes
We carry Felpro brand parts for your Chevrolet Bel Air across several catalog categories, including Intake Manifold Parts. Some of our most reviewed Felpro parts include:
FAQs for Chevrolet Bel Air Air Intakes
What are the most purchased Air Intakes for the Chevrolet Bel Air?
Out of 220 Air Intakes for the Chevrolet Bel Air, the most popular in our inventory are:
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$31.99
(18)
Ultra-Seal Intake Manifold Gasket with Silicone Beading
Intake Manifold Gasket Sets
What are the top-rated Chevrolet Bel Air Air Intakes?
Top-rated Air Intakes for your Chevrolet Bel Air based on customer reviews/ratings are:
from
$456.99
(45)
Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny
“Very satisfied”
from
$26.99
(12)
Intake Manifold Gasket for 1958-1986 Small-Block Chevy
“Edlebrock gasket is what I needed, they had in stock! Ordered online and picked up at the counter”
