Chevrolet 3E Belts and Hoses
Top Chevrolet 3E Belts and Hoses Categories
We carry over 22 Belts and Hoses in inventory for the Chevrolet 3E. If you’re looking for aftermarket Belts and Hoses for your Chevrolet 3E, check out all these categories:
Essential Chevrolet 3E Belts and Hoses
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Gates – Automotive XL« High Capacity V-Belt (Part No.9425)
from
$29.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Dayco – V-Belt, Top Cog, Dayco (Part No.17415)
from
$15.49
Dayco® High Performance V-Belt is the workhorse of the heavy-duty industry. Polyester cord provides maximum power transfer and tension holding capability for the life of the belt. The laminated construction helps absorb greater shock loads associated with diesel engines. These Dayco® High Performance V-Belt advantages translate into less downtime, lower maintenance costs, and increased dependability. Dayco’s High Performance V-Belt meets or exceeds SAE J636 and J637 specifications.
Product Features:
See More
Product Features:
- The High Performance V-Belt design delivers more flexibility and increases airflow around the belt, so it runs cooler and lasts longer than most competitive belts
- Polyester cord provides maximum power transfer and tension holding capability for the life of the belt
- The laminated construction helps absorb greater shock loads associated with diesel engines
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Driveworks – Automotive V-Belt, Driveworks (Part No.42517)
from
$2.99
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Dayco – Bottom Cog V-Belt; 54.75 Inch Long, Exact Fit Premium Quality (Part No.17548)
from
$20.79
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Driveworks – Automotive V-Belt (Part No.41517)
from
$4.99
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Dayco – Flex Radiator Hoses; EPDM Rubber, 18.75 Inch Long, 1.75 Inch Inner Dia. (Part No.81341)
from
$18.79
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Gates – Premium Molded Coolant Hose (Part No.20584)
from
$33.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
ACDelco – Professional Molded Coolant Hose (Part No.G2000576796ACD)
from
$44.48
ACDelco Professional, premium aftermarket Molded Coolant Hoses are composed of specially blended materials to help resist electrochemical degradation (ECD), the leading cause of hose failure. They are specially designed, GM OE style factory-molded hoses to fit today’s smaller, tighter-fitting engine compartments. ACDelco Professional Molded Coolant Hoses are temperature rated from -40 degrees Fahrenheit to 275 degrees Fahrenheit (-40 degrees Celsius to 135 degrees Celsius) and are approved for Marine applications. Do not use for fuel or oil transfer applications. These premium aftermarket replacement molded coolant hoses are manufactured to meet or exceed your expectations for fit, form, and function.
Product Features:
See More
Product Features:
- Has a heat and ozone resistant cover to increase the life of the hose
- Comes with a protective sleeve to help duplicate GM OE designs for proper fit and function
- Made of re-engineered materials to resist vacuum collapse and also reduce the need for internal springs in many applications
- Installs without buckling, bending out of shape, or straining at the connection for easy installation
- Inside diameters ranges from 1?4 in to 1 in to fit different types of vehicles
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25478)
from
$16.99
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Green Stripe« Heavy-Duty Vulco-Flex« Coolant Hose (Part No.26611)
from
$34.99
Heavy-duty flexible hose designed to replace straight or curved coolant hoses. The benefit is maximum coverage with minimum inventory. Hose inside diameter remains constant from end to end. No convolutions inside hose so tube is smooth, allowing free coolant flow. Approved for marine applications.
Product Features:
See More
Product Features:
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Built-in steel spiral wire allows for medium sized curves without kinking or collapsing
- EPDM tube and Neoprene cover for extended service life
- Polyester fabric-ply reinforcement vulcanizes into shape without unnecessary strain on connections
- Resistant to heat, oil and ozone
- Performs to SAE 20R5 Type EC Class D-2 specifications
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Caution: Do not use for fuel or oil transfer applications.
Dayco – Flex Radiator Hoses; EPDM Rubber, 17.25 Inch Long, 1.5 Inch Inner Dia. (Part No.81171)
from
$20.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Flex Radiator Hoses; EPDM Rubber, 10.75 Inch Long, 1.5 Inch Inner Dia. (Part No.81131)
from
$18.29
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Gates – Premium Molded Coolant Hose (Part No.20046)
from
$26.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Green Stripe« Heavy-Duty Vulco-Flex« Coolant Hose (Part No.26612)
from
$40.99
Heavy-duty flexible hose designed to replace straight or curved coolant hoses. The benefit is maximum coverage with minimum inventory. Hose inside diameter remains constant from end to end. No convolutions inside hose so tube is smooth, allowing free coolant flow. Approved for marine applications.
Product Features:
See More
Product Features:
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Built-in steel spiral wire allows for medium sized curves without kinking or collapsing
- EPDM tube and Neoprene cover for extended service life
- Polyester fabric-ply reinforcement vulcanizes into shape without unnecessary strain on connections
- Resistant to heat, oil and ozone
- Performs to SAE 20R5 Type EC Class D-2 specifications
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Caution: Do not use for fuel or oil transfer applications.
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.25" Long, 1.50" Diameter (Part No.D70440)
from
$13.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Chevrolet 3E Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your Chevrolet 3E
You love your 3E. So we’ve made it easier than ever to help you find Chevrolet 3E Belts and Hoses in our online catalog. Our inventory holds 22 aftermarket and OEM Belts and Hoses for your Chevrolet 3E, ranging from $2.99 to $79.99.
We offer parts from 5 brands trusted to make quality Belts and Hoses for your Chevrolet 3E. Before you buy, take some time to read through customer reviews. We currently have 9 reviews of Chevrolet 3E Belts and Hoses from previous customers.
Find your 3E Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Chevrolet 3E part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your Chevrolet 3E
Our inventory holds Belts and Hoses for your Chevrolet 3E from 5 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Imperial, and Gates, all of which can keep that Chevrolet happy.
We have Driveworks parts available for your Chevrolet 3E in categories like Serpentine and V Belts. Some of the top-rated Driveworks parts in these categories are:
Top-Rated Dayco Belts and Hoses
Leading Dayco Belts and Hoses
We carry Dayco brand parts for your Chevrolet 3E across several catalog categories, including Radiator Hoses and Engine Cooling Hoses. Some of our most reviewed Dayco parts include:
from
$18.79
(3)
Flex Radiator Hoses; EPDM Rubber, 18.75 Inch Long, 1.75 Inch Inner Dia.
Coolant Hoses
from
$20.49
(1)
Flex Radiator Hoses; EPDM Rubber, 17.25 Inch Long, 1.5 Inch Inner Dia.
Upper Radiator Hoses
FAQs for Chevrolet 3E Belts and Hoses
What are the most purchased Belts and Hoses for the Chevrolet 3E?
Out of 22 Belts and Hoses for the Chevrolet 3E, the most popular in our inventory are:
from
$18.29
This product is not rated
Flex Radiator Hoses; EPDM Rubber, 10.75 Inch Long, 1.5 Inch Inner Dia.
Upper Radiator Hoses
