BMW 525i Alternators and Starters

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Rein OE quality bolts kits fit European vehicles the way the original manufacturer intended. Designed to be direct replacements for the original bolts are identical to OEM. Supplied with all the necessary bolts and torque specs to ensure that the job is done right.

Product Features:

• Includes all the bolts needed to complete the job.
• Comes with torque specs to make sure each bolt is properly tighten.
• Manufactured to strict engineering standards/specifications in materials and tolerances.
• Aluminum bolts are torque to yield and must be replaced once they are released.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
• Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
• Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• BUILT TO LAST — Advanced heat treatment process for strength
• PREMIUM MATERIALS — Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE — Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

This Litens supplied OAP is manufactured by the original equipment (O.E.) manufacturer. This replacement pulley is exact in all form, fit, and performance characteristics as the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). Under rapid engine deceleration, the pulley disengages the alternator from the belt drive system, allowing the alternator to freewheel, re-engaging when the RPM increases. The OAP alternator pulley ensures smooth, quiet performance. The OAP is designed as a sacrificial part of the front-end accessory drive system, protecting other belt driven component. Under normal driving conditions, the original pulley will require replacement in approximately 70,000 – 90,000 miles. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Product Features:

• Original Equipment Design
• Protects the front-end accessory drive components
• New seal cap included with the OAP (Always ensure the cap is installed after installation)
• Tools Required – 17mm Spline Bit Driver (included)
• Installation instructions included

ALTERNATOR PULLEY

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• 100% remanufactured drive clutch assembly ensures lasting performance
• Armatures and commutators are 100% load tested
• New motor lead terminals and solenoid contacts are used to ensure maximum connectivity
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Bosch Premium Starters are designed, built and tested to provide the ultimate in performance and reliability.

Product Features:

• Built for extremes! Our new and reman starters and alternators are 100% factory tested to ensure reliable performance, under extremes of heat, cold and high demand
• Our new and reman starters and alternators are designed to perform equal to or better than the original equipment parts, that they replace
• Our new and reman starters and alternators are designed to be identical in fit and performance to original equipment parts
• Our new and reman starters and alternators utilize the latest manufacturing technologies and highest quality parts to ensure the best performance and longest life

Product Features:

• Engineered to meet or exceed OEM specifications for a perfect fit and hassle-free installation.
• Premium grade solenoids contains materials specifically selected for best conductivity. High temperature cap ensures that the solenoid works flawlessly in high heat environments. High dielectric strength outer case resists shorting.
• Armatures have precision machined and upgraded steel shaft for improved durability and performance.
• Each unit includes a printed copy of the test results so you know exactly what to expect from our parts right from the first time they power on.

Product Features:

• Engineered to meet or exceed OEM specifications for a perfect fit and hassle-free installation.
• Premium grade solenoids contains materials specifically selected for best conductivity. High temperature cap ensures that the solenoid works flawlessly in high heat environments. High dielectric strength outer case resists shorting.
• Armatures have precision machined and upgraded steel shaft for improved durability and performance.
• Each unit includes a printed copy of the test results so you know exactly what to expect from our parts right from the first time they power on.

As a recognized expert in Electrical Systems since 1923, Valeo is a global top supplier of original equipment starters. As an original equipment partner to all major car manufacturers, 1 in 3 vehicles worldwide are equipped with an original Valeo electrical system. Valeo premium starters are 100% new, eliminating the risk of premature failure.

Product Features:

• Valeo premium starters are 100% new products (not remanufactured)
• All components are 100% new eliminating premature failure for increased durability over remanufactured units
• Direct replacement ensuring a perfect fit and easy installation
• Extreme condition testing ensuring reliability under the harshest demands: noise, vibration, corrosion, durability
• Speed, temperature, and electrical measurement tests can undergo up to 40,000 cycles to ensure dependable performance
• Part Number 438272 is the original equipment part now available in the aftermarket.

Bosch Premium Starters are designed, built and tested to provide the ultimate in performance and reliability.

Product Features:

• Built for extremes! Our new and reman starters and alternators are 100% factory tested to ensure reliable performance, under extremes of heat, cold and high demand
• Our new and reman starters and alternators are designed to perform equal to or better than the original equipment parts, that they replace
• Our new and reman starters and alternators are designed to be identical in fit and performance to original equipment parts
• Our new and reman starters and alternators utilize the latest manufacturing technologies and highest quality parts to ensure the best performance and longest life

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

The Bosch Premium Alternator, delivering 170 amps and 12 VDC, is engineered for exceptional performance and reliability. Full-load tested to meet Bosch’s rigorous performance standards, this alternator ensures dependable operation under demanding conditions. Unlike rebuilt units, it is 100% factory-tested and remanufactured using high-quality materials and cutting-edge technology, offering superior durability and longevity. Designed with a clockwise rotation direction, it is built to handle the toughest electrical demands while maintaining consistent power output. Whether you’re replacing a worn-out alternator or upgrading for better performance, this premium unit provides outstanding value and peace of mind.

Product Features:

Product Features:
• Full-load tested to guarantee compliance with Bosch’s strict performance specifications
• 100% factory tested, units are remanufactured (not rebuilt)
• Built to last – uses high quality materials and the most technologically advanced developments.
• Engineered for consistent power output, ensuring reliable performance under demanding electrical conditions.
• Designed with a clockwise rotation direction to optimize compatibility and efficiency in applicable systems.

The Bosch Premium Alternator, delivering 150 amps at 12 VDC, is engineered for exceptional performance and reliability. Full-load tested to meet Bosch’s rigorous performance standards, this alternator ensures dependable operation under demanding conditions. Unlike rebuilt units, it is 100% factory-tested and remanufactured using high-quality materials and cutting-edge technology, guaranteeing long-lasting durability. Designed with a clockwise rotation direction, it is built to seamlessly integrate into your vehicle’s electrical system. Whether you’re replacing a worn-out alternator or upgrading for enhanced performance, this Bosch alternator offers unmatched value and peace of mind.

Product Features:

Product Features:
• Full-load tested to guarantee compliance with Bosch’s strict performance specifications
• 100% factory tested, units are remanufactured (not rebuilt)
• Built to last – uses high quality materials and the most technologically advanced developments.
• Seamlessly integrates with your vehicle’s electrical system for reliable and efficient operation.
• Designed with a clockwise rotation direction to ensure compatibility and optimal performance.

The Bosch Premium Alternator delivers exceptional performance and reliability, making it a top choice for demanding automotive needs. With a robust 140-amp output and 12 VDC voltage, this alternator ensures consistent power delivery for your vehicle’s electrical systems. Engineered with precision, it features full-load testing to meet Bosch’s stringent performance standards and is 100% factory tested for quality assurance. Unlike standard rebuilds, this unit is remanufactured using high-quality materials and cutting-edge technology, ensuring long-lasting durability. Its clockwise rotation direction and advanced design make it a dependable replacement part that stands up to rigorous use. Choose this alternator for a reliable, high-performance solution that keeps your vehicle running smoothly.

Product Features:

Product Features:
• Full-load tested to guarantee compliance with Bosch’s strict performance specifications
• 100% factory tested, units are remanufactured (not rebuilt)
• Built to last – uses high quality materials and the most technologically advanced developments.
• Designed for demanding automotive applications, the 140-amp output ensures consistent and reliable power delivery to support your vehicle’s electrical systems.
• Precision-engineered with a clockwise rotation direction for seamless integration and dependable performance in your vehicle.

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading limited warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading limited warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• 100% new OE-quality brushes and bearings are used to ensure long service life
• Rotors and stators are load tested and double insulated for maximum charging performance
• Slip rings are precision polished for maximum brush contact and service life
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading limited warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading limited warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• 100% new OE-quality brushes and bearings are used to ensure long service life
• Rotors and stators are load tested and double insulated for maximum charging performance
• Slip rings are precision polished for maximum brush contact and service life
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Valeo’s premium alternator, boasting a robust 150-amp output and 12 VDC voltage, is engineered for exceptional performance and reliability. Crafted entirely from 100% new components, this alternator eliminates the risk of premature failure often associated with remanufactured units, ensuring long-lasting durability. Designed with application-specific parts for a precise fit, it incorporates premium rare earth magnets to maximize efficiency without increasing size. Rigorous testing under extreme conditions for up to six months guarantees reliability even in the harshest environments, while its high resistance to heat, vibration, and contaminants ensures consistent charge output. With a clockwise rotation direction and original equipment quality, this Valeo alternator is now available in the aftermarket as Part Number 439486, offering unmatched value and innovation. Perfect for demanding electrical systems, it enhances fuel economy and eliminates voltage drops, making it a top choice for those seeking superior performance and dependability.

Product Features:

• Valeo premium alternators are 100% new products (not remanufactured)
• 100% new components and core eliminates premature failure for increased durability over remanufactured units
• All parts are application specific for an exact fit
• Premium rare earth magnets increase the output of the alternator without increasing the size for better efficiency
• All applications go under extreme condition testing up to 6 months to ensure reliability under the harshest conditions and electrical demands
• High resistance to heat, vibration, and contaminating particles helps maintain maximum charge output
• Part Number 439486 is the original equipment part now available in the aftermarket.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• 100% new OE-quality brushes and bearings are used to ensure long service life
• Rotors and stators are load tested and double insulated for maximum charging performance
• Slip rings are precision polished for maximum brush contact and service life
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

The Bosch Premium Alternator, delivering a robust 120-amp output and operating at 14 VDC, is engineered for exceptional performance and reliability. Designed with precision, it ensures consistent power delivery to meet the demands of modern vehicles. Its clockwise rotation direction guarantees compatibility with a wide range of applications, making it a dependable choice for your vehicle’s electrical system. Built to Bosch’s high standards, this alternator is rigorously tested to withstand the toughest conditions, ensuring long-lasting durability and peak efficiency. Whether you’re replacing a worn-out unit or upgrading for better performance, this alternator offers excellent value and peace of mind for your automotive needs.

Product Features:

Product Features:
• Provides a robust 120-amp output to efficiently power modern vehicle electrical systems.
• Operates at 14 VDC for consistent and reliable energy delivery.
• Clockwise rotation direction ensures compatibility with a wide range of vehicle applications.
• Engineered with precision and rigorously tested for durability in tough conditions.
• Built to Bosch’s high standards for long-lasting performance and reliability.