Bentley Continental Performance and Racing Products

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:

• Gold Dichromate Finish For Extreme Off Road Environments
• Single Feed Fuel Inlet For Ease Of Installation
• Optimized Off-Road Calibration That Works Out-Of-The-Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• One Piece Off-Road Vent Tube Eliminates Fuel Spillover
• Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
• Limited Lifetime Warranty Defects In Material/Workmanship

Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,

Product Features:

• Vibratory Polished For Good Looks

Product Features:

• FRD 10BLT 7.5 R/P 4.56 MGP

The ultimate shifter for automatic transmission equipped street vehicles! The Hi-Tek Street bandit has all the same feature as the above Street Bandit line of shifters, with an interchangeable billet knob design.

Product Features:

• Ideal For High-Tech Pro-Street
• Ideal For High-Tech Street Rods
• Narrow Styled Aluminum Housing
• Includes Neutral Safety Switch
• Includes Backup Light Switch
• Includes Billet Aluminum Knob
• Can Be Used w/Reverse Pattern Valve Body

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer
• Washer Between Turbine and Cover

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer