Autocar AT Belts and Hoses
Top Autocar AT Belts and Hoses Categories
We carry over 35 Belts and Hoses in inventory for the Autocar AT. If you’re looking for aftermarket Belts and Hoses for your Autocar AT, check out all these categories:
Essential Autocar AT Belts and Hoses
Gates – Green Stripe Truck & Bus Series V-Belt (Part No.TR22657)
from
$56.99
Specifically designed for heavy-duty truck, bus and off-road equipment applications. Absorbs normal shock loads without damage to the belt.
Product Features:
See More
Product Features:
- Molded grooves reduce bending stress, especially on small diameter pulleys, while also dissipating heat.
- High modulus, high strength tensile cord
- Oil and heat resistant construction
- Meets SAE J636b and SAE J637 specifications
- Meets RMA oil and heat resistant standards and static conductivity requirements
- NOTE: Some sizes are available as Gates PowerBand V-belts.
Dayco – Bottom Cog V-Belt; 58 Inch Long, Exact Fit Premium Quality (Part No.17580)
from
$20.99
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Gates – Automotive XL High Capacity V-Belt (Part No.9447)
from
$40.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- The fiber-reinforced rubber support adds flexibility along the belt and provides greater lateral stability on the pulley.
- Ground to ensure precise dimensional control of the top width and side wall for proper fit to the pulley.
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resistant to oil, heat, ozone, weathering and aging for a longer belt life.
- Meets or exceeds SAE J636C specifications
Dayco – V-Belt, Top Cog, Dayco (Part No.28403)
from
$18.79
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- áDesigned for efficient power transmission to vehicle accessories in today’s trucks and buses
- áProvides greater durability and flexibility ┐ 35% stronger than all previous versions
- áFeatures specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5.25" Long, 2.50" Diameter (Part No.B70923)
from
$18.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – FleetRunner Heavy-Duty Micro-V Serpentine Drive Belt (Part No.K060435HD)
from
$54.99
Gates Fleet Runner Micro-V Belts are designed for the toughest applications. Fleet Runner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures, making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. Fleet Runner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- The patented material provides maximum performance at extreme and prolonged operating temperatures.
- The construction resists cracking and wear, even at extreme temperatures.
- A special compound offers unparalleled flexibility, stability, load capacity, and belt lifespan.
- Problem solver designed for the toughest applications
- It consistently outperforms other heavy-duty serpentine belts on the market
- Engineered to save your fleet money and reduce downtime
- Replacing the tensioner is recommended (if the vehicle is equipped with one).
Dayco – Straight Radiator Hoses; EPDM Rubber, 2 1/4 Inch Inner Diameter (sold by inch) (Part No.76225)
from
$1.79
The Dayco Straight Radiator Hose is designed for a wide range of light and heavy duty truck applications where the radiator hose routing is relatively straight. Note: This hose is NOT suitable for fuel or oil transfer.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-2 requirements
- Features a high strength knitted reinforcement and synthetic EPDM rubber construction
- Resistant to standard coolants, ozone and other detrimental environmental elements
- PLEASE NOTE: Priced and sold by inch. See store for details.
Dayco – Straight Radiator Hoses; EPDM Rubber, 1 1/2 Inch Inner Diameter (sold by inch) (Part No.76150)
from
$1.29
The Dayco Straight Radiator Hose is designed for a wide range of light and heavy duty truck applications where the radiator hose routing is relatively straight. Note: This hose is NOT suitable for fuel or oil transfer.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-2 requirements
- Features a high strength knitted reinforcement and synthetic EPDM rubber construction
- Resistant to standard coolants, ozone and other detrimental environmental elements
- PLEASE NOTE: Priced and sold by inch. See store for details.
Gates – Molded 90 Degree Heater Hose (Part No.28466)
from
$19.99
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
Product Features:
See More
Product Features:
- Resistant to electrochemical degradation and water permeation
- Use with heating pipe connectors and bulk heating hoses to create custom assemblies
- Compatible for coolant, air, and water applications
- EPDM tube and lid, reinforced with synthetic fibers
- SAE 20R3 CE Class D1, SAE 20R4 CE Class D1
- temperature range Deg. F to +275 degrees F (-40 degrees C to +135 degrees C)
- Caution: Do not use for fuel or oil transfer applications
Dayco – Straight Radiator Hoses; EPDM Rubber, 1 1/4 Inch Inner Diameter (sold by inch) (Part No.76125)
from
$0.99
The Dayco Straight Radiator Hose is designed for a wide range of light and heavy-duty truck applications where the radiator hose routing is relatively straight. Note: This hose is NOT suitable for fuel or oil transfer.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-2 requirements.
- Features a high strength knitted reinforcement and synthetic EPDM rubber construction
- Resistant to standard coolants, ozone and other detrimental environmental elements
Gates – Molded 90 Degree Heater Hose (Part No.28474)
from
$15.79
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
Product Features:
See More
Product Features:
- It resists electrochemical degradation and water permeation
- Use with heating pipe connectors and bulk heating hoses to create custom assemblies
- Compatible with cooling, air and water applications
- EPDM tube and cover, synthetic fiber reinforcement
- SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
- temperature range Deg. F to +275 degrees F (-40 degrees C to +135 degrees C)
- Caution: Do not use for fuel or oil transfer applications
Dayco – Straight Radiator Hoses; EPDM Rubber, HD, 3 Inch Inner Dia. (Sold by inch) (Part No.77300GL)
from
$2.99
Designed for a wide range of heavy-duty truck applications where the routing is relatively straight, the Dayco straight radiator hose – H.D. is made with the highest quality woven mesh fabric reinforcement, neoprene cover and nitrile tube compounds to withstand the most corrosive elements in diesel engines. Providing protection from oil, coolants, coolant additives and heat, it has a temperature rating of -40 Deg. F (-40 Deg. C) to +212 Deg. F (+100 Deg. C).
Product Features:
See More
Product Features:
- Capable of withstanding extreme temperatures and high-pressure environments
- Designed to meet SAE requirements J20R1, Class B Tube, Class C Cover, standard wall construction
- Not suitable for fuel or oil transfer
- PLEASE NOTE: Item is sold and priced by the inch. See store for details.
Gates – Green Stripe 2-Ply Straight Coolant Hose (Sold by inch) (Part No.24220)
from
$1.99
Stick hose designed for demanding heavy-duty coolant/air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Cover marked in 1-inch increments to facilitate approximate cut lengths, allows for “custom” installations.
- Designed with compounds that resist electrochemical degradation
- Approved for marine applications
- Exceeds SAE 20R1 Type EC (Class D-1 Tube, and cover, Standard Wall)
- Temperature range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: For a maintenance-free connection, use PowerGrip SB clamps
- Caution: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the inch. See store for details.
Gates – Premium Molded Coolant Hose (Part No.21400)
from
$32.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Materials specifically designed to resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube; synthetic fiber knit reinforcement; heat-, ozone- and chemical coolant-resistant EPDM cover
- Compliant with the requirements of SAE 20R4, class D2 and DIN 73411, class A standards (except with regard to tolerances)
- temperature range Deg. F to +257 degrees F (-40 degrees C to +125 degrees C)
- Note: Gates recommends replacing clamps and connectors every time a new cooling hose is installed.
- Caution: Do not use for fuel or oil transfer applications
Dayco – Straight Radiator Hoses; EPDM Rubber, 2 1/2 Inch Inner Diameter (sold by inch) (Part No.76250)
from
$1.79
Designed for a wide range of light and heavy duty truck applications where the radiator hose routing is relatively straight, Dayco’s Straight Radiator Hose features knitted einforcement and synthetic EPDM rubber construction. It meets SAE J20R4, Class D-2 requirements and provides high strength and resistance to ozone and other detrimental environmental elements, coolants, and temperature variations from -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C). Note: This hose is NOT suitable for fuel or oil transfer.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-2 requirements
- Features a high strength knitted reinforcement and synthetic EPDM rubber construction
- Resistant to standard coolants, ozone and other detrimental environmental elements
- Works well in temperatures ranging from -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C)
- PLEASE NOTE: Priced and sold by inch. See store for details.
Autocar AT Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your Autocar AT
You love your AT. So we’ve made it easier than ever to help you find Autocar AT Belts and Hoses in our online catalog. Our inventory holds 35 aftermarket and OEM Belts and Hoses for your Autocar AT, ranging from $0.99 to $65.99.
We offer parts from 3 brands trusted to make quality Belts and Hoses for your Autocar AT. Before you buy, take some time to read through customer reviews. We currently have 223 reviews of Autocar AT Belts and Hoses from previous customers.
Find your AT Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Autocar AT part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your Autocar AT
Our inventory holds Belts and Hoses for your Autocar AT from 3 trusted brands. You’ll find OEM and aftermarket parts from brands like Driveworks, Dayco, and Gates, all of which can keep that Autocar happy.
We have Dayco parts available for your Autocar AT in categories like Serpentine and V Belts. Some of the top-rated Dayco parts in these categories are:
FAQs for Autocar AT Belts and Hoses
What are the most purchased Belts and Hoses for the Autocar AT?
Out of 35 Belts and Hoses for the Autocar AT, the most popular in our inventory are:
from
$1.29
This product is not rated
Straight Radiator Hoses; EPDM Rubber, 1 1/2 Inch Inner Diameter (sold by inch)
By-Pass Hoses
from
$1.79
This product is not rated
Straight Radiator Hoses; EPDM Rubber, 2 1/4 Inch Inner Diameter (sold by inch)
By-Pass Hoses
