Audi S8 Alternators and Starters

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• 100% remanufactured drive clutch assembly ensures lasting performance
• Armatures and commutators are 100% load tested
• New motor lead terminals and solenoid contacts are used to ensure maximum connectivity
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Product Features:

• Engineered to meet or exceed OEM specifications for a perfect fit and hassle-free installation.
• Premium grade solenoids contains materials specifically selected for best conductivity. High temperature cap ensures that the solenoid works flawlessly in high heat environments. High dielectric strength outer case resists shorting.
• Armatures have precision machined and upgraded steel shaft for improved durability and performance.
• Each unit includes a printed copy of the test results so you know exactly what to expect from our parts right from the first time they power on.

The Bosch Premium Starter is engineered for top-tier performance and reliability, making it a dependable choice for your vehicle’s ignition system. Designed with a clockwise (right) rotation and featuring a 10-tooth configuration, this starter ensures precise engagement and smooth operation. Operating at 12 VDC, it delivers consistent power to get your engine running efficiently every time. Built to Bosch’s high standards, this remanufactured starter undergoes rigorous testing to meet or exceed OEM specifications, ensuring long-lasting durability and optimal functionality. Whether you’re replacing a worn-out starter or upgrading for better performance, this premium component offers excellent value and peace of mind for your vehicle’s starting system.

Product Features:

Product Features:
• Engineered for top-tier performance and reliability, ensuring dependable ignition system operation.
• Designed with a 10-tooth configuration for precise engagement and smooth functionality.
• Operates at 12 VDC to deliver consistent and efficient power for reliable engine starts.
• Remanufactured to meet or exceed OEM specifications, guaranteeing long-lasting durability.
• Undergoes rigorous testing to ensure optimal functionality and adherence to Bosch’s high standards.

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• 100% remanufactured drive clutch assembly ensures lasting performance
• Armatures and commutators are 100% load tested
• New motor lead terminals and solenoid contacts are used to ensure maximum connectivity
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Engineered for top-tier performance and reliability, ensuring dependable ignition system operation.
• Designed with a 9-tooth configuration for precise engagement and smooth functionality.
• Operates at 12 VDC to deliver consistent power, meeting the demands of modern vehicles.
• Remanufactured to Bosch’s high standards, undergoing rigorous testing for durability and long-lasting performance.

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading limited warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading limited warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• 100% new OE-quality brushes and bearings are used to ensure long service life
• Rotors and stators are load tested and double insulated for maximum charging performance
• Slip rings are precision polished for maximum brush contact and service life
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading limited warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading limited warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• 100% new OE-quality brushes and bearings are used to ensure long service life
• Rotors and stators are load tested and double insulated for maximum charging performance
• Slip rings are precision polished for maximum brush contact and service life
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

The Ignition switch is the main power switched distribution point in every vehicle. The ignition switch in some manner will be connected directly to the vehicle battery and then supply power out to every operating system in the vehicle that is required to be connected and disconnected from the vehicle’s battery or power source.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.