Audi A6 Alternators and Starters

Bosch Premium Starters are designed, built and tested to provide the ultimate in performance and reliability.

When your vehicle needs a new starter, you need to treat your car right. Replace it with a Premium Quality remanufactured starter from OE+. All of our starters are completely remanufactured to meet or exceed O.E. specifications. The solenoid is completely remanufactured or replaced with new. The brush plate holder is cleaned and plated for corrosion prevention. The armature is tested and recoated. The commutator is remachined or replaced for proper brush contact. The drive is completely remanufactured or replaced. The gear is chamfer checked. All housings are cleaned and refinished to prevent corrosion.

Product Features:

• OE-Equivalent Direct Fit Application.
• Fully tested to meet OE specifications.
• Provides exceptional reliability.

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

More and more performance, less and less consumption – in order to meet the high demands placed on modern engines, automobile manufacturers demand the absolute highest levels of performance from the engine components used. The oil circuit is of central importance here, as only clean engine oil can permanently ensure consistent engine performance. If the circulating oil is not permanently freed of impurities and combustion residues, protection from wear is no longer guaranteed. In the worst case, this may even damage the engine. If you want to play it safe when choosing an oil filter, choose MANN-FILTER. They are designed for modern high-performance oils and can stand up to even the most demanding technical challenges. As the application areas of oil filters and the demands placed on them vary, MANN-FILTER oil filters are available in different designs.

Product Features:

• Outstanding dirt holding capacity
• Prolongs service intervals and continues to meet the technical requirements of high-performance engines
• Offers even faster and optimized oil supply when starting the engine

The Vemo Relay is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Premium aftermarket replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Voltage Regulator

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

• CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
• CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

Bosch has been a major supplier of new alternators and starters to OE vehicle manufacturers since 1913. Securing OE certification requires strict adherence to stringent precision and performance criteria. These same exacting criteria are also applied in the manufacturing of all Bosch aftermarket alternators and starters. Whether 100% remanufactured or new, Bosch Premium Alternators and Starters are quality built and 100% factory tested to ensure years of reliable performance, even under the most extreme operating conditions. That’s why they are preferred by more professional installers.

Product Features:

• Built to last using the highest quality materials and the most technologically advanced manufacturing processes
• Remanufactured using more new parts than any other unit
• 100% exhaustive multipoint quality and performance testing throughout the remanufacturing process ensures optimum starting and charging performance under all operating conditions
• Every unit is full-load tested to guarantee compliance with Bosch strict performance specifications
• Voltage regulator 100% tested for OE voltage specifications (new on GM and Ford)
• Rectifier 100 % tested (new on Ford)
• Diodes 100% tested (replaced with new as required)
• Rotor 100% performance-tested for maximum electrical output
• 100% new long life sealed bearings with special high load, high temperature grease
• Stator 100% insulation and phase balance tested
• Slip rings 100% new or remachined to +/- .05mm, the tightest tolerance in the industry
• 100% new long life self-lubricating brushes
• 100% new clutch pulleys
• All terminals, insulators and hardware provided

Bosch has been a major supplier of new alternators and starters to OE vehicle manufacturers since 1913. Securing OE certification requires strict adherence to stringent precision and performance criteria. These same exacting criteria are also applied in the manufacturing of all Bosch aftermarket alternators and starters. Whether 100% remanufactured or new, Bosch Premium Alternators and Starters are quality built and 100% factory tested to ensure years of reliable performance, even under the most extreme operating conditions. That’s why they are preferred by more professional installers.

Product Features:

• Built to last using the highest quality materials and the most technologically advanced manufacturing processes
• Remanufactured using more new parts than any other unit
• 100% exhaustive multipoint quality and performance testing throughout the remanufacturing process ensures optimum starting and charging performance under all operating conditions
• Every unit is full-load tested to guarantee compliance with Bosch strict performance specifications
• Voltage regulator 100% tested for OE voltage specifications (new on GM and Ford)
• Rectifier 100 % tested (new on Ford)
• Diodes 100% tested (replaced with new as required)
• Rotor 100% performance-tested for maximum electrical output
• 100% new long life sealed bearings with special high load, high temperature grease
• Stator 100% insulation and phase balance tested
• Slip rings 100% new or remachined to +/- .05mm, the tightest tolerance in the industry
• 100% new long life self-lubricating brushes
• 100% new clutch pulleys
• All terminals, insulators and hardware provided

Bosch Premium Alternators are designed, built and tested to provide the ultimate in performance and reliability.

Product Features:

• Full-load tested to guarantee compliance with Bosch’s strict performance specifications
• 100% factory tested, units are remanufactured (not rebuilt)
• Built to last – uses high quality materials and the most technologically advanced developments.

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Alternator

Dayco OAPs (Overrunning Alternator Pulleys) allow the alternator to ‘freewheel’ when the belt speed drops and they are engineered with one-way clutches that allows the rotational inertia of the alternator to overrun during any belt deceleration event. Dayco OAPs, which are designed for long service life, decrease drive belt vibration and reduce belt slippage during rapid acceleration or deceleration, resulting in reduced stress on the drive belt and other accessories as well as increased alternator and drive belt life. Dayco OAPs are application-specific replacement parts. If a vehicle requires an OAP, the same type of pulley must be installed. Proper tools must be used to remove and install OAPs.

Product Features:

• Designed for long service life
• Decreases drive belt vibration
• Reduces belt slippage during rapid acceleration or deceleration
• Reduces stress on the drive belt and other accessories

Litens Automotive is the original equipment supplier to Audi/VW for this decoupling alternator pulley. This replacement pulley is also designed and produced by Litens and is exact in all form, fit, and performance characteristics as the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). Decoupling pulleys are engine specific and should never be interchanged with other types of pulley technology. The Litens OAD type pulley is designed to free-wheel in one direction and, with an internal spring and damping device, softly engage in the opposite direction. The OAD is designed as a sacrificial part of the front-end accessory drive system, protecting other belt driven component as well as the alternator. The correct decoupler pulley ensures smooth, quiet performance as well as increasing vehicle gas mileage. Under normal driving conditions, the original pulley will require replacement in approx. 60,000 – 70,000 miles. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Product Features:

• Patented Original Equipment Design
• Protects the alternator and other front-end accessory drive components.
• Installation instructions included.
• New plastic cap included with the OAD.
• Tools Required – Litens recommends using a long 10mm 12 point driver bit (also known as a triple square) and a 17×20 spline tool such as a Metal Nerd MNXZ10 and a Miller Special Tools P/N 8823 and a torque wrench.
• Professional mechanics can install this replacement OAD in approximately 2 hour. During alternator replacement, belts, tensioners, and routing pulleys should be inspected.
• 56.2mm O.D.; 17mm I.D; 40.6mm width; ribbed running surface for a 6-rib serpentine belt; high-grade steel construction. 17mm Spline bit driver Included for ease of installation.

Ignition Lock Housin

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

Ignition Lock Cylind

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.