Audi 5000 Belts and Hoses
Top Audi 5000 Belts and Hoses Categories
We carry over 50 Belts and Hoses in inventory for the Audi 5000. If you’re looking for aftermarket Belts and Hoses for your Audi 5000, check out all these categories:
Essential Audi 5000 Belts and Hoses
ContiTech – Drive V-Belt (Part No.W100033147CON)
from
$21.08
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Polyester fiber tensile members and a ribbed belt design.
Dayco – Bottom Cog V-Belt; 31 Inch Long, Exact Fit Premium Quality (Part No.15310)
from
$17.29
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
Gates – Automotive XL« High Capacity V-Belt (Part No.9390)
from
$30.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Dayco – Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia. (Part No.81031)
from
$27.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 6 Inch Length (Part No.80411)
from
$7.79
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 25 Inch Length (Part No.80415)
from
$20.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.5" Inside Diameter (Sold by foot) (Part No.28410)
from
$3.29
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25251)
from
$30.49
Product Features:
See More
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Flex Radiator Hoses; EPDM Rubber, 17.25 Inch Long, 1.25 Inch Inner Dia. (Part No.81051)
from
$21.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12.50" Long, 1.22" Diameter (Part No.D70960)
from
$18.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia. (Part No.81041)
from
$14.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.75" Inside Diameter (Sold by foot) (Part No.28412)
from
$3.99
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
CRP – HOSE – FUEL (Part No.4L30010807CRP)
from
$596.98
HOSE – FUEL
CRP – Fuel Hose (Part No.E5000859948CRP)
from
$110.20
Fuel Hose
CRP – Hose – Fuel (Part No.4L30010817CRP)
from
$486.90
Hose – Fuel
CRP – Hose – Fuel (Part No.4L30010809CRP)
from
$233.30
Hose – Fuel
Audi 5000 Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your Audi 5000
You love your 5000. So we’ve made it easier than ever to help you find Audi 5000 Belts and Hoses in our online catalog. Our inventory holds 50 aftermarket and OEM Belts and Hoses for your Audi 5000, ranging from $3.29 to $596.98.
We offer parts from 6 brands trusted to make quality Belts and Hoses for your Audi 5000. Before you buy, take some time to read through customer reviews. We currently have 1,179 reviews of Audi 5000 Belts and Hoses from previous customers. Some of the top rated parts include Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia. with 2.3 stars and V-Belt, Top Cog with 4.0 stars.
Find your 5000 Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Audi 5000 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your Audi 5000
Our inventory holds Belts and Hoses for your Audi 5000 from 6 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Gates, and CRP, all of which can keep that Audi happy.
We have Driveworks parts available for your Audi 5000 in categories like Serpentine and V Belts. Some of the top-rated Driveworks parts in these categories are:
Top-Rated Dayco Belts and Hoses
Leading Dayco Belts and Hoses
We carry Dayco brand parts for your Audi 5000 across several catalog categories, including Serpentine and V Belts and Radiator Hoses. Some of our most reviewed Dayco parts include:
from
$21.99
(8)
Flex Radiator Hoses; EPDM Rubber, 17.25 Inch Long, 1.25 Inch Inner Dia.
Coolant Hoses
from
$14.99
(8)
Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia.
By-Pass Hoses
FAQs for Audi 5000 Belts and Hoses
What are the most purchased Belts and Hoses for the Audi 5000?
Out of 50 Belts and Hoses for the Audi 5000, the most popular in our inventory are:
What are the top-rated Audi 5000 Belts and Hoses?
Top-rated Belts and Hoses for your Audi 5000 based on customer reviews/ratings are:
from
$27.49
(3)
Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia.
“well satisfied”
from
$19.49
(1)
V-Belt, Top Cog
“USED THIS AS A REPLACEMENT ON MY MERCURY 3.0 OUTBOARD. THESE ARE TOP OF THE LINE BELTS AND SHE PERFORMED PERFECT. NO SLIP AND COULD SEE AND FEEL THE”
