AMC AMX Alternators and Starters

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by a Limited Warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Each unit is triple-tested to ensure quality and performance
• All wear components (brushes, bushings, and bearings) are replaced with all NEW components in the remanufacturing process
• Tech Hotline with trained ASE Certified Technicians: Call Carquest Technical Support at 1-800-228-9672
• Remanufactured to meet or exceed OE specifications, ensuring reliable fit, form, and function for optimal vehicle performance.
• 100% electronic testing of critical components and the entire unit guarantees dependable operation and long-lasting durability.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Our knock sensors are designed to respond to knock frequencies up to 1000 Hz accommodating shifts in engine knock frequency making it a more flexible sensor responding to correct engine knock over a broad range of vehicle conditions
• Manufacturing processes include an automated data acquisition system to continuously monitor the sensor output to ensure that it responds with appropriate voltage output at the specified frequency range
• All units are 100% tested using an accelerometer vibration test to ensure trouble-free operation
• Featuring the broadest sensor coverage in the market, we meet the service professionals needs with the highest quality product every time he opens the box
• BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product

The Starter Solenoid is the relay of the starting circuit that carries the high amperage required when the starter motor is engaged. The solenoid is typically energized by the starter switch when commanded by the vehicle operator. Starter solenoids may also be used in other high amperage circuits, compare solenoid specification to your circuit needs before installing.

Product Features:

• Application matched component to ensure the system can be returned to like new condition.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The Bosch Premium Alternator, delivering 63 amps at 12 VDC, is engineered for exceptional performance and reliability. Full-load tested to meet Bosch’s rigorous performance standards, this alternator ensures dependable operation under demanding conditions. Unlike rebuilt units, it is 100% factory-tested and remanufactured using high-quality materials and cutting-edge technology, guaranteeing long-lasting durability. Designed with a clockwise rotation direction, it is built to seamlessly integrate into your vehicle’s electrical system. Whether you’re replacing a worn-out alternator or upgrading for better performance, this Bosch alternator offers unmatched value and peace of mind.

Product Features:

Product Features:
• Full-load tested to guarantee compliance with Bosch’s strict performance specifications
• 100% factory tested, units are remanufactured (not rebuilt)
• Built to last – uses high quality materials and the most technologically advanced developments.
• Seamlessly integrates with your vehicle’s electrical system, ensuring optimal compatibility and performance.
• Engineered for dependable operation under demanding conditions, providing reliable power delivery when you need it most.

The Bosch Premium Alternator is engineered for top-tier performance and reliability, making it a dependable choice for your vehicle’s electrical system. This remanufactured unit is not just rebuilt but meticulously crafted using high-quality materials and advanced technology to ensure long-lasting durability. With a 55-amp output and 12 VDC voltage rating, it delivers consistent power to meet your vehicle’s demands. Full-load and 100% factory testing guarantee compliance with Bosch’s stringent performance standards, so you can trust its reliability under various conditions. Designed for clockwise rotation, this alternator is a perfect fit for vehicles requiring precision and efficiency. Choose Bosch for a premium solution that combines functionality, durability, and value.

Product Features:

Product Features:
• Full-load tested to guarantee compliance with Bosch’s strict performance specifications
• 100% factory tested, units are remanufactured (not rebuilt)
• Built to last – uses high quality materials and the most technologically advanced developments.
• Designed for precision and efficiency, ensuring optimal performance for vehicles requiring clockwise rotation.
• Delivers consistent 55-amp output to reliably meet the electrical demands of your vehicle.

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Product Features:

• RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
• PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

The Ignition switch is the main power switched distribution point in every vehicle. The ignition switch in some manner will be connected directly to the vehicle battery and then supply power out to every operating system in the vehicle that is required to be connected and disconnected from the vehicle’s battery or power source.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

This ignition lock cylinder is designed to match the fit, function and performance of the original equipment part on specified vehicles. It is engineered to help restore ignition lock function when an original cylinder is broken or worn out.

Product Features:

• Direct replacement – this ignition lock cylinder matches the fit and function of the original equipment assembly on certain vehicle years, makes and models
• Ideal solution – engineered to help restore and ensure the functionality of the lock cylinder
• Durable construction – designed and manufactured to strict specifications for reliable performance
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

• CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
• CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

• CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
• CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.