2017 Subaru WRX STI Belts and Hoses

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Radiator Hose

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:

• Has all the quality features of Gates molded coolant hose and similar to OEM specifications
• Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
• EPDM tube, synthetic fiber knit reinforcement, EPDM cover
• Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
• Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:

• OE-Equivalent.
• Direct fit for easy installation.
• Resistant against wear, oil and heat.
• Strong tensile cords limit stretching.
• Supports higher horsepower loads.
• Made from high strength synthetic rubber.

Dayco ela (elastic) or stretch belts are specifically designed for two, three, and four point drives that are designed to use self-tensioning belts. Although these belts may look like standard poly rib belts, they are very different. These specially designed elastic belts have self-tensioning capabilities required by specific OE drives. Vehicles that are manufactured with stretch belts must replace them with stretch belts. These belts are not interchangeable with standard constructed belts of their same size. Dayco ela belts utilize a proprietary EPDM construction that is designed to elongate over the fixed pulley system, and then maintain the required belt tension over the life of the belt. The backbone behind the Dayco ela belt is its specially developed polyamide tensile member, which allows for high elongation required for installation, yet provides the proper tension maintenance properties to transmit the accessory loads demanded for the drive. This belt construction incorporates a wear resistant EPDM rib material, along with a highly elastic EPDM cushion rubber that surrounds the polyamide tensile cord, thus providing the required adhesion and flexibility to maintain lasting performance. Stretch belts have unique installation instructions depending on the OE application. Installation may require a specialized tool for the application or a simple zip tie. Do not attempt to install by prying the belt on the pulleys. Dayco provides detailed instructions on the reverse side of the sleeve.

Product Features:

• Utilizes a proprietary EPDM construction that is designed to elongate over the fixed pulley system, and then maintain the required belt tension over the life of the belt
• Specially developed polyamide tensile member, which allows for high elongation required for installation, yet provides the proper tension maintenance properties to transmit the accessory loads demanded for the drive
• Incorporates a wear resistant EPDM rib material, along with a highly elastic EPDM cushion rubber that surrounds the polyamide tensile cord, thus providing the required adhesion and flexibility to maintain lasting performance
• These specially designed elastic belts have self-tensioning capabilities required by specific OE drives designed for a stretch belt

Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.

Product Features:

• Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
• EPDM rubber constructions resist cracking on the rib surface
• Meets or exceeds all specifications from the Original Equipment Manufacturer
• Tensioner Replacement is Recommended (if equipped)
• Unique form grinding of each individual belt assures precise dimensional control.
• Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.

The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:

• Constructed with heat and ozone resistant EPDM rubber
• Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
• Made with treated polyester cord to reduce belt stretch

Dayco ela self-tensioning belts incorporate a wear-resistant EPDM rib material, along with a highly elastic EPDM cushion rubber that surrounds the polyamide tensile cord, thus providing the required adhesion & flexibility to maintain lasting performance. The backbone behind the Dayco ela self-tensioning belt is its polyamide tensile member, which allows the high elongation required for installation, yet provides the proper tension maintenance properties to transmit the accessory loads demanded for the drive.

Product Features:

• Designed for two- to four-point drives that do not require automatic or manual tensioning.
• Provides self-tensioning capabilities required by specific OE drives designed for a stretch’ belt
• Elasticity allows for long-lasting performance and proper tension
• Elasticityáallows for long-lasting performance and proper tension

Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:

• Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
• Engineered to help address noise issues caused by the belt drive 
• Capable of handling more extreme temperatures and workloads