Name: Pre-Pressed Rear Axle
Brand: Dorman
SKU: 926-140
Price: 803.99 USD

from

$803.99

Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.

Product Features:

Pre-Pressed Rear Axle
Pre-Pressed Rear Axle
Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.
Easier installation – this loaded axle assembly includes a pre-assembled new axle shaft, wheel bearing, hub and backing plate
Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components

from

$236.99

DiffrlCarrBng

from

$399.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Toyota Tacoma and T100 without factory locking differential
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$136.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. Side shims included.

Product Features:

Fits reverse rotation Toyota Landcruiser
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$428.32

Differential Shift A

from

$404.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits standard rotation Toyota 7.5″
7.500″ ring gear diameter
23 spline pinion
10 ring gear bolts
5.29 ratio

from

$276.99

Yukon small hole yoke for ’82 and older Toyota T100 and Tacoma (with locker) with 27 spline pinion. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Toyota Tacoma and T100 with factory locking differential
27 spline

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$188.99

Bearing race driver for rear Toyota V6, Landcruiser reverse rotation, and Tacoma with locker. (TOY35028). No return.

Product Features:

Bearing race driver
Fits 35028 race
All steel construction

from

$889.99

8″ IFS clamshell carrier, 3.91 and up, 07 & up FJ, 05 & up TAC/T100/TNDRA.

Product Features:

Standard open carrier case
Does not include spider gears
Fits Toyota 8″ clamshell front
3.91 and up ratios only

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$176.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT BRG & SEAL TOYOTA 7.5 IFS FRONT +86-88+ALL REAR 2WD-45MM CARR BRGS

from

$23.99

Toyota 29spl V6 and clamshell front, outer oil slinger.

Product Features:

Outer slinger
Fits Toyota 8″ clamshell front

from

$9.99

Toyota 7.5 pinion nut (M18x1.5).

Product Features:

Pinion nut for Toyota 7.5″
18mm x 1.5 thread

from

$23.99

V6 side gear Thrust washer.

Product Features:

Side gear thrust washer
Fits Toyota V6

from

$461.99

Yukon standard open spider gear kit for Toyota T100 & Tacoma with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Toytoa Tacoma and T100 open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin spider gear thrust washers.

from

$6.99

Ring Gear bolt for Toyota 7.5″, 8″, V6, Landcruiser reverse front & T100/Tacoma w/ factory locker. 11mm x 1.0.

Product Features:

Ring gear bolt for Toyota 7.5″, 8″, 8″ V6, Landrcuiser reverse rotation front and T100 and Tacoma rear with factory locking differential
11mm x 1.0

from

$364.99

Yukon Performance 10 bolt steel spool for V6 Toyota with 30 spline axles. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

Fits Toyota V6 rear
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$42.99

Product Features:

TOYOTA 8″ V6&4CLY TURBO

from

$298.99

Product Features:

Cross pin shaft
Fits Toyota V6

from

$53.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Matched cup and cone components ensures consistent quality and outstanding performance
Industry leading coverage
Professional technicians know they can depend on National

from

$7.99

Oil baffle for Toyota Landcruiser reverse rotation front, 8″ IFS front & TV6/Tacoma rear with factory locker.

Product Features:

Oil baffle
Fits Toyota Landcruiser reverse rotation front

from

$8.99

Product Features:

Roll pin
Fits Toyota Tacoma and T100

from

$27.99

Pinion preload shim for Toyota T100. One single shim. 0.033″ thick. Two needed. Fits against crush sleeve.

Product Features:

Fits Toyota T100 and Tacoma
0.140″ thick

from

$9.99

Product Features:

Brand may vary by location

from

$73.99

Differential Crush S

from

$11.65

Pinion Seal

from

$34.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft