2014 Dodge Challenger Vehicle Hoods

Crown Automotive offers the largest line of replacement parts for Jeep(R), as well as a growing line of parts for Chrysler and Dodge. Our applications comes with Axle, Body, Brake, Clutch, Cooling, Electrical, Engine, Fuel, Lamps, Mirrors, Steering, Suspension, Transmission and Wiper.

Hood release cable broken? This hood release cable is durably built to directly replace a worn-out or broken cable on specific vehicle years, makes and models.

New Standard Replacement Hood Panel, Without Hood Scoop, Made Of Aluminum

Lift supports are pressurized cylinders that are used to support hoods, hatches and rear window glass in automotive applications. Lift supports are also used in many non-automotive applications. Each Strongarm lift support is custom engineered, and manufactured beyond industry standards to provide smoother operating, and longer lasting performance. Lift supports should be replaced in pairs to ensure safe, reliable support of your hood, hatch, or liftgate.

“Atlas Lift Supports are engineered to meet or exceed OE specifications to ensure your replacement will perform the same or better than your original lift supports. Atlas Lift supports are designed to prevent premature failures, with premium features such as a corrosion resistant exterior, OE grade end connectors, and Dynamic Dampening Technology. Dynamic Dampening Technology (DDT) is a precision groove engineered into the tube of the lift support, which allows the hatch to open at the optimum speed to prevent “”bouncing”” or “”Jumping”” at the end of the stroke. Lift Supports’ performance and longevity are affected by consistent usage, temperature changes, contact with weather elements, pulling or hanging on the part, and can cause unsafe conditions if not changed when signs of failure are present. Atlas Lift Supports are easy to replace and can be changed in minutes No Special Tools Required. Atlas Lift Supports also provide easy to read install for a quick and easy installation. Make sure to Always Replace in Pairs!”

These short travel retro-fit XD hydraulic roller lifters feature a billet seat and short travel. These lifters’ short travel allows for light pre-load and reduced oil volume for the highest revving lifter for Chrysler 6.4 HEMI.

Competition Cams 10 Degree Steel Retainer for 26120 Beehive Spring, 795-1.

This non-link bar hydraulic roller lifter features short travel. This lifter’s short travel allows for light pre-load and reduced oil volume for the highest revving lifter for GEN III Chrysler 6.4L HEMI’s.

“Engineered as a premium upgrade, the COMP Cams Non-MDS Lifters for Dodge Gen III HEMI engines, keep all 8 cylinders engaged at all times, allowing the use of performance camshafts without concerns about lifter failure. Designed as a major upgrade over the commonly sourced Dodge “”Hellcat”” lifters, this unique design enhances oil retention around the axle and bearing, helping to reduce wear and increase durability in all applications, stock to high performance. Additionally, extra material is strategically placed at the bottom of the lifter, adding strength and stiffness to the critical roller area. An ideal replacement for factory units, this drop-in lifter is designed to protect against roller bearing wear and lifter body breakage, it’s ideal for any stock, high performance or racing application. COMP Cams Non-MDS Dodge Gen III HEMI Lifters are available with or without lifter yokes. COMP lifter yokes perfectly align the lifters and are manufactured from a premium material to meet all factory/OEM requirements. One lifter yoke holds four non-MDS HEMI lifters, four yokes needed per engine.”

This Flowmaster Outlaw Cat-back exhaust system is designed for the 2015-2023 Dodge Challenger SRT 392 and R/T Scat Pack models with the 6.4L engine, the SRT Hellcat with 6.2L engine and the 2017-2021 R/T with the 5.7L engine. The system is perfect for the person looking for a very aggressive exterior sound level when hard on the gas while maintaining a moderate tone when cruising. System features include dual 3.00-inch mandrel-bent stainless steel tubing flowing into our exclusive Scavenger Series X-pipe for a deep unique sound while making maximum power. The tubing then runs into a pair of race-proven Outlaw Series mufflers and the tailpipes include high-quality active exhaust valves ready for your factory actuators. The system is then finished off with quad 3.50-inch 304 stainless steel embossed tips for a muscular look. The system is covered by our Limited Warranty and includes all necessary parts and hardware for an easy installation you can do at home.

Crown Automotive offers the largest line of replacement parts for Jeep (R), as well as a growing line of parts for Chrysler and Dodge vehicles. Our applications features Axle, Body, Brake, Clutch, Cooling, Electrical, Engine, Fuel, Lamps, Mirrors, Steering, Suspension, Transmission and Wiper.

Auveco products provide OE fit & function.

Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.

New Standard Replacement Passenger Side Hood Hinge

New Standard Replacement Driver Side Hood Hinge

New Goodmark Driver Side Hood Hinge Assembly