from

$329.99

8.5″ van axle, 2WD-30spline, 6 LUG, 34-1/2″ 03 and up. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects.

Product Features:

28 spline
6 lug
34.25″ long
Fits GM 8.5″ in 2003-2012 GM van

from

$10.99

8.2″ & 8.5″ rear cover gasket.

Product Features:

Cover gasket
Fits GM 8.2″, 8.5″ and 8.6″

from

$55.88

Differential Pinion

from

$11.29

SHAFT SEAL

from

$182.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear. .

Product Features:

Fits 2009 and up GM 8.6″
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$8.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$389.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 1997 and down GM 9.5″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$561.99

Yukon spider gear set for GM 9.5″ Gura Drip posi. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.

Product Features:

Spider gear kit
Fits GM 9.5″ with Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$5.99

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$231.99

This Motive Gear Differential Rebuild Kit includes all of the parts required to rebuild your stock open differential. The gears are lapped for quiet operation. Includes spider and side gears, cross shaft, lock pin or bolt and thrust washers.

Product Features:

GM8.6″ INTERNAL KIT (OPEN) 30 SPL. MID 2000-2008

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$9.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$219.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M88010 race
All steel construction

from

$12.52

Differential Drain P

from

$108.39

Differential Cover with Hardware Included

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$16.49

TAPERED ROLLER BEARI

from

$29.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$17.99

Standard open side gear thrust washer for 7.2″ GM.

Product Features:

Side gear thrust washer
Fits GM 7.2″ IFS

from

$263.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set. This kit is used in 8.5″ differentials using a Yukon Dura Grip, Eaton posi, ValueTrac, True Trac, Pro-Series Auburn, Detroit Locker or standard carrier with large bearing journals.

Product Features:

Fits GM 8.5″ rear with aftermarket positraction
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve , marking compound and brush.

from

$7.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$59.99

Product Features:

Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
Interlocking design makes installation much easier

from

$7.99

GM 7.2″ IFS Ring Gear bolt. 7/16″ x 20.

Product Features:

Ring gear bolt
Fits GM 7.2″ IFS
7/16″ x 20

from

$15.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$929.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit has larger bearing journals for added strength & uses heavy-duty carrier bearings & races.

Product Features:

Fits GM 8.5″ and 8.6″ with 30 spline axles
2.73 ratio and up only
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA