from

$243.90

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$14.59

This wheel disc hardware kit includes rubber components used to protect the caliper pins or bolts. Worn or cracked rubber components will allow excessive movement of guide pins or bolts.

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$30.97

Brake Pad Sensor

from

$14.11

Brake Adjuster

from

$9.99

Brake Vacuum Pump Ga

from

$34.99

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

Wearever Brake Shoes come bonded or riveted based on OE design.
Wearever Brake Shoes are coated to prevent rust.
Wearever Brake Shoes are 100% New not remanufactured.
Brand may vary by location

from

$36.99

This automotive brake hydraulic hose was precision-engineered to match the fit, function and performance of the original brake hose on specific vehicles and positions to ensure safe, long-lasting durability as part of a complete brake repair.

Product Features:

Ideal replacement – precision-engineered to match the performance of the original brake hose on specific vehicles
Position-specific – manufactured to precise measurements to provide an exact fit and easy installation
Quality assured – materials tested to exacting government-regulated safety and durability standards
Durable design – made with EPDM rubber and specially coated, corrosion-resistant fittings
Brand may vary by location

from

$4.99

Brakes are designed as a system and all the parts need to work together for best performance. The boot and square cut seals included in our Caliper Repair Kit, ensure that the caliper works as designed during the apply and release cycle.

Product Features:

This part matches Original Equipment (OE) quality specifications
Increases the life span of the brake pads
Restores brakes to like-new performance
Prevents noise and premature wear
Direct replacement for a proper fit

from

$85.99

Carquest Wearever rotors meet or exceed original equipment specifications while delivering superior stopping power. Carquest Wearever rotors are manufactured with proper harmonic design and non-directional finish that eliminate noise and enhance pedal feel. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of your pads and rotors. Carquest Wearever rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to preventing warping
Air gap eliminates brake fade and increases pad life
Non-directional finish decreases break-in time

from

$122.99

Carquest Wearever rotors meet or exceed original equipment specifications while delivering superior stopping power. Carquest Wearever rotors are manufactured with proper harmonic design and non-directional finish that eliminate noise and enhance pedal feel. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of your pads and rotors. Carquest Wearever rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to preventing warping
Air gap eliminates brake fade and increases pad life
Non-directional finish decreases break-in time

from

$20.00

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

Reduced cost
OE Quality
Complete Kit

from

$6.01

Dorman’s Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Replacement restores disc brakes to proper operation
Replacement prevents uneven braking
Direct replacement for a proper fit
Manufactured to strict engineering quality standards

from

$74.99

Carquest Platinum Professional brake pads are a premium alternative to original equipment brake pads that provide superior stopping performance, quieter braking and cleaner wheels. All CQ Platinum Professional brake pads are manufactured by a vertically

Product Features:

Industry-leading number of application specific formulations for maximum performance and extended pad life
On-vehicle testing similar to original equipment tests
Patented 4-Layer HEX Shim Technology provides quiet braking
HEX shim design utilizes aramid fibers, the same fibers used in bulletproof vests, to reduce shim wear
Burnishing compound allows for a faster break-in of pads and rotors
PTFE coated hardware and caliper pin grease included for nearly every application
Wear sensors included on most European applications that require replacement
Powder-coated backing plate prevents corrosion

from

$536.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit comes with everything you need, from pads, rotors and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Brake rotor, pad & hardware engineered to work together to increase stopping power, improve durability & eliminate dust
Rotors are zinc plated for maximum protection against rust.
Includes 1 Front Sensor Wire
Buy with confidence from the originator & industry leader of brake kits

from

$1.85

The ATE Caliper Guide Pin Cover is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$172.91

TRW Automotive supplies master cylinder brake actuation systems featuring quality and performance. TRW’s master cylinder product portfolio covers a wide range of vehicles, from small cars up to truck and SUV platforms. These systems can offer lighter weight, with options such as micro master cylinders and aluminum master cylinders through to heavy-duty master cylinders designed for the durability and variable loading conditions of the light-truck market. These systems function with the help of a series of brake fluid sensors, which are located on the reservoir tank. This series includes vacuum sensors, brake light switches, and travel sensors.

Product Features:

Low volume uptake
High efficiency
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS

from

$7.49

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. Caliper Guide Pins are important to replace because they hold the brake piston in place to create effective stopping performance.

Product Features:

This part matches Original Equipment (OE) quality specifications
Easy and fast replacement
Helps deliver a quieter, more efficient braking system
Corrosion resistant coating for long-lasting durability against harsh roads
Manufactured with quality materials to suppress high stress levels

from

$43.99

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

Dependable stopping power
Single layer shim for quiet braking
OE-designed slots and chamfers to reduce noise and vibration
Powder-coated backing plate prevents corrosion

from

$13.89

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$108.99

Brake Fluid Level Sensor

from

$77.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$62.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$23.99

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

This part matches Original Equipment (OE) quality specifications
Exact fitment and original replacement
New Brake Hardware prevents premature wear and maximizes performance
Helps deliver a quieter, more efficient braking system
Manufactured with quality materials to suppress high stress levels

from

$27.49

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

This part matches Original Equipment (OE) quality specifications
Exact fitment and original replacement
New Brake Hardware prevents premature wear and maximizes performance
Helps deliver a quieter, more efficient braking system
Manufactured with quality materials to suppress high stress levels

from

$222.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit comes with everything you need, from pads, rotors and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Brake rotor, pad & hardware engineered to work together to increase stopping power, improve durability & eliminate dust
Rotors are zinc plated for maximum protection against rust.
Includes 1 Rear Sensor Wire
Buy with confidence from the originator & industry leader of brake kits

from

$759.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Our Z26 Street Warrior Brake Upgrade Kit is recommended for high performance, high horsepower muscle and modified cars. This kit comes with everything you need for easy installation, including pads, rotors and stainless-steel hardware. The Drilled & Slotted rotors and Carbon-Fiber Ceramic pads combine to provide shorter stops under the most demanding conditions. This PowerStop Z26 Street Warrior Brake Upgrade Kit is the affordable bolt-on upgrade that delivers more than just the braking power you need to rein in all those ponies. With our low-dust and low-noise formula, you’ll spend less time cleaning those wheels and more time enjoying what matters most – the drive.

Product Features:

This complete brake kit has been engineered to handle the increased demand of street-driven muscle cars and performance vehicles
Proprietary Carbon-Fiber Ceramic Z26 brake pads enhance heat dissipation versus a typical ceramic brake pad for better stopping power at high speed
Stainless-steel pad shims resist the increased temperatures common on high performance applications
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Drilled & Slotted performance rotors provide maximum cooling
Bolt-on upgrade for stock brakes, no modifications necessary
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Brake rotor, pad & hardware engineered to work together to increase stopping power & enhance heat dissipation for your performance car
Rotors are zinc plated for maximum protection against rust.
Includes 1 Front & 1 Rear Sensor Wire
Buy with confidence from the originator & industry leader of brake kits

from

$362.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit comes with everything you need, from pads, rotors and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Brake rotor, pad & hardware engineered to work together to increase stopping power, improve durability & eliminate dust
Rotors are zinc plated for maximum protection against rust.
Includes 1 Front Sensor Wire
Buy with confidence from the originator & industry leader of brake kits