2013 Toyota Camry Heater Hoses

Essential 2013 Toyota Camry Heater Hoses

Gates – Premium Molded Heater Hose (Part No.18021)

Premium Molded Heater Hose

from

$23.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 15 1/2 Inch Length (Part No.86121)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 15 1/2 Inch Length

from

$29.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 15 1/2 Inch Length (Part No.87883)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 15 1/2 Inch Length

from

$33.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 6 Inch Length (Part No.80400)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 6 Inch Length

from

$18.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Dayco – Dayco, Heater Hose (Part No.R30301221037DAY)

Dayco, Heater Hose

from

$12.27
Designed to replace original equipment manufacturer hose, Dayco Molded Heater Hose are built with knitted reinforcement and EPDM construction which provides high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C) that are required for OEM hose replacements. The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose. The Dayco Molded Radiator and Bypass Hose has a convenient plastic hang strap for quick and easy merchandising. In addition to meeting SAE J20R4, Class D-1 requirements, this hose is now designed to meet Type EC electro- chemical requirements as specified in SAE J1684.

Product Features:
  • Made with synthetic EPDM rubber compounds that provide resistance to deterioration from ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C)
  • The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose
  • Meets SAE J20R4, Class D-1 requirements for improved service hose
  • Meets Type EC electro-chemical requirements as specified in SAE J1684; which eliminates premature deterioration of the inner tube caused by the build up of static electric charges
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 19 1/2 Inch Length (Part No.87819)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 19 1/2 Inch Length

from

$23.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 10 Inch Length (Part No.87977)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 10 Inch Length

from

$32.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 1/2 Inch Diameter, 6 Inch Length (Part No.80393)

Molded Heater Hose; EPDM Rubber, 1/2 Inch Diameter, 6 Inch Length

from

$10.49
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 13 Inch Length (Part No.87850)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 13 Inch Length

from

$56.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length (Part No.80403)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length

from

$11.99
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Gates – Premium Molded Heater Hose (Part No.19161)

Premium Molded Heater Hose

from

$58.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Dayco, Heater Hose (Part No.R3030264337DAY)

Dayco, Heater Hose

from

$9.52
Designed to replace original equipment manufacturer hose, Dayco Molded Radiator and Bypass Hose are built with knitted reinforcement and EPDM construction which provides high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C) that are required for OEM hose replacements. The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose. The Dayco Molded Radiator and Bypass Hose has a convenient plastic hang strap for quick and easy merchandising. In addition to meeting SAE J20R4, Class D-1 requirements, this hose is now designed to meet Type EC electro- chemical requirements as specified in SAE J1684.

Product Features:
  • Made with synthetic EPDM rubber compounds that provide resistance to deterioration from ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C)
  • The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose
  • Meets SAE J20R4, Class D-1 requirements for improved service hose
  • Meets Type EC electro-chemical requirements as specified in SAE J1684; which eliminates premature deterioration of the inner tube caused by the build up of static electric charges
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 12-1/2 Inch Length (Part No.87849)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 12-1/2 Inch Length

from

$16.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 5/16 Inch Length (Part No.87818)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 5/16 Inch Length

from

$21.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 17 Inch Length (Part No.87844)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 17 Inch Length

from

$35.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 24 1/2 Inch Length (Part No.88482)

Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 24 1/2 Inch Length

from

$58.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 5 1/4 Inch Length (Part No.87625)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 5 1/4 Inch Length

from

$15.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 17 Inch Length (Part No.87724)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 17 Inch Length

from

$25.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length (Part No.87821)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length

from

$14.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Molded 90 Degree Heater Hose (Part No.28466)

Molded 90 Degree Heater Hose

from

$19.29
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:
  • Resists electrochemical degradation and water permeation
  • Use with heater hose connectors and bulk heater hose to create custom assemblies
  • Compatible for coolant, air and water applications
  • EPDM tube and cover, synthetic fiber reinforcement
  • SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
  • Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 12 1/2 Inch Length (Part No.86801)

Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 12 1/2 Inch Length

from

$29.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length (Part No.86123)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length

from

$18.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Straight Heater Hose: EPDM Rubber, Universal Fit, 5/16" Inside Diameter (Sold by foot) (Part No.80258)

Straight Heater Hose: EPDM Rubber, Universal Fit, 5/16" Inside Diameter (Sold by foot)

from

$0.83
Specifically designed to carry the heated coolant from the engine block to the heater core under the dashboard and return it to the engine, this Dayco Standard Heater Hose is constructed using all EPDM compounds and spiral reinforcement for high burst strength and excellent heat resistance. Made for general service on light trucks and passenger cars, this hose is similar to SAE 20R3, Class D-2 and has a temperature rating of -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C). This Dayco Standard Heater Hose is compatible with all common coolant and coolant additives. Note: This hose is NOT suitable for fuel or oil transfer.

Product Features:
  • Specifically designed to be compatible with all common coolants and coolant additives
  • Constructed using all EPDM compounds and spiral reinforcements
  • Similar to SAE 20R3, Class D-2
  • Has a high burst strength and excellent heat resistance of -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C)
  • PLEASE NOTE: Item is sold and priced by the foot. See store for details.
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 14 5/16 Inch Length (Part No.87820)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 14 5/16 Inch Length

from

$20.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length (Part No.87935)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length

from

$52.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Molded 90 Degree Heater Hose (Part No.28468)

Molded 90 Degree Heater Hose

from

$16.99
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:
  • Resists electrochemical degradation and water permeation
  • Use with heater hose connectors and bulk heater hose to create custom assemblies
  • Compatible for coolant, air and water applications
  • EPDM tube and cover, synthetic fiber reinforcement
  • SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
  • Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Premium Molded Heater Hose (Part No.18738)

Premium Molded Heater Hose

from

$18.29
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 19 1/4 Inch Length (Part No.87642)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 19 1/4 Inch Length

from

$17.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

2013 Toyota Camry Heater Hoses

Maybe you’re in the middle of a full rebuild of that 2013 Toyota Camry. Maybe you just need a couple of Heater Hoses. Either way, Advance Auto Parts has 2 different Heater Hoses in our inventory ranging from $18.29 to $21.29. That means you can find the exact parts or products you need to keep that 2013 Toyota Camry running smoothly.

Heater Hoses are only as good as their brand. We stock 1 different brands to make sure you have plenty of trusted parts to choose from for your 2013 Toyota Camry. Dayco are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Heater Hoses for your 2013 Toyota Camry, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.

So if you’re in the market for aftermarket Heater Hoses to keep your 2013 Toyota Camry rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Heater Hoses Brands To Make Your 2013 Toyota Camry Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 2013 Toyota Camry demands trusted brand parts and products to keep it running. Many trusted brands of Heater Hoses make up Advance Auto Parts’ inventory, and all are ready to help make your Camry the best it can be. Be sure to browse some of our top Heater Hoses brands and parts.