2012 Dodge Challenger Vehicle Hoods

Crown Automotive offers the largest line of replacement parts for Jeep(R), as well as a growing line of parts for Chrysler and Dodge. Our applications comes with Axle, Body, Brake, Clutch, Cooling, Electrical, Engine, Fuel, Lamps, Mirrors, Steering, Suspension, Transmission and Wiper.

This non-link bar hydraulic roller lifter features short travel. This lifter’s short travel allows for light pre-load and reduced oil volume for the highest revving lifter for GEN III Chrysler 6.4L HEMI’s.

Flowmaster’s American Thunder Cat-back exhaust system for the 2015-2023 Dodge Challenger SXT is perfect for the person looking for a moderate exterior sound level while maintaining a mild interior sound with all of the performance benefits that you would expect from Flowmaster. This bolt-on cat-back 409S stainless steel system for the 3.6L engine features 2.50-inch mandrel-bent tubing and includes a Scavenger X-pipe crossover for a unique deep sound and maximum power. The dual Super 44 Series mufflers flow into dual 2.50-inch mandrel-bent tailpipes which are finished off with tuned resonators and stainless steel tips that exit within the rear bumper valance. The exhaust system is covered by our Limited Warranty, is designed for an easy fit and includes all necessary parts and hardware for installation.

“Engineered as a premium upgrade, the COMP Cams Non-MDS Lifters for Dodge Gen III HEMI engines, keep all 8 cylinders engaged at all times, allowing the use of performance camshafts without concerns about lifter failure. Designed as a major upgrade over the commonly sourced Dodge “”Hellcat”” lifters, this unique design enhances oil retention around the axle and bearing, helping to reduce wear and increase durability in all applications, stock to high performance. Additionally, extra material is strategically placed at the bottom of the lifter, adding strength and stiffness to the critical roller area. An ideal replacement for factory units, this drop-in lifter is designed to protect against roller bearing wear and lifter body breakage, it’s ideal for any stock, high performance or racing application. COMP Cams Non-MDS Dodge Gen III HEMI Lifters are available with or without lifter yokes. COMP lifter yokes perfectly align the lifters and are manufactured from a premium material to meet all factory/OEM requirements. One lifter yoke holds four non-MDS HEMI lifters, four yokes needed per engine.”

Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.

New Standard Replacement Driver Side Hood Hinge

New Standard Replacement Passenger Side Hood Hinge

New Goodmark Driver Side Hood Hinge Assembly

Hood release cable broken? This hood release cable is durably built to directly replace a worn-out or broken cable on specific vehicle years, makes and models.

New Standard Replacement Hood Panel, Without Hood Scoop, Made Of Aluminum

Crown Automotive offers the largest line of replacement parts for Jeep (R), as well as a growing line of parts for Chrysler and Dodge vehicles. Our applications features Axle, Body, Brake, Clutch, Cooling, Electrical, Engine, Fuel, Lamps, Mirrors, Steering, Suspension, Transmission and Wiper.

Auveco products provide OE fit & function.

“Atlas Lift Supports are engineered to meet or exceed OE specifications to ensure your replacement will perform the same or better than your original lift supports. Atlas Lift supports are designed to prevent premature failures, with premium features such as a corrosion resistant exterior, OE grade end connectors, and Dynamic Dampening Technology. Dynamic Dampening Technology (DDT) is a precision groove engineered into the tube of the lift support, which allows the hatch to open at the optimum speed to prevent “”bouncing”” or “”Jumping”” at the end of the stroke. Lift Supports’ performance and longevity are affected by consistent usage, temperature changes, contact with weather elements, pulling or hanging on the part, and can cause unsafe conditions if not changed when signs of failure are present. Atlas Lift Supports are easy to replace and can be changed in minutes No Special Tools Required. Atlas Lift Supports also provide easy to read install for a quick and easy installation. Make sure to Always Replace in Pairs!”

Lift supports are pressurized cylinders that are used to support hoods, hatches and rear window glass in automotive applications. Lift supports are also used in many non-automotive applications. Each Strongarm lift support is custom engineered, and manufactured beyond industry standards to provide smoother operating, and longer lasting performance. Lift supports should be replaced in pairs to ensure safe, reliable support of your hood, hatch, or liftgate.