from

$12.81

Expansion Tank Cap

from

$38.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$2.04

Water Pump Hsng Gask

from

$38.99

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 1 minute

from

$6.79

Cracked or lost the original engine coolant reservoir cap? Replace it seamlessly and effectively with this precisely engineered, direct replacement cap.

Product Features:

Direct replacement – this engine coolant reservoir cap directly replaces a cracked or lost original cap.
Application specific – made to match dimensions of reservoir cap on only certain vehicle years, makes and models
Seamless fit – reverse-engineered from the original equipment to fit perfectly
Excellent value – a quick, easy replacement that’s less expensive than going back to the dealership

from

$11.83

Water Outlet O-Ring

from

$99.99

Product Features:

Motors built and tested to quality specifications
14 in. universal fit reversible fan
1250 CFM
UNIVERSAL fan, NOT a direct OE replacement. Measure core and verify space.

from

$38.49

Controls the operating temperature of Imperial electric fans. Operates up to 2 fans.

Product Features:

Preset thermostatic fan control
185°F preset
For use with Imperial electric fans
Probe installs into radiator fins

from

$47.99

This replacement engine coolant reservoir is manufactured from quality materials to withstand the stresses of underhood heat and engine vibration. It is engineered and manufactured to match the fit and function of the original part.

Product Features:

Direct replacement – this engine coolant reservoir matches the fit and function of the original part.
Ideal solution – engineered for a seamless installation.
Durable construction – manufactured from quality materials to withstand underhood heat and vibration
Trustworthy design – backed by 100 years of automotive aftermarket experience

from

$3.99

GM Genuine Parts Engine Coolant Water Outlet Adapter Gaskets are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
Original equipment parts are designed to work with your GM vehicle safety systems — aftermarket replacement parts may not meet the same OE safety regulations, depending on the part type
GM regularly updates production and service part designs to integrate new materials and technologies

from

$21.99

MAHLE gaskets provide world class sealing products trusted by OEMs & Technicians around the globe.

Product Features:

All MAHLE gaskets meet or exceed the original equipment specifications providing the finest sealing products available
MAHLE gaskets utilizes OE equivalent or better materials in all our gaskets
MAHLE gaskets is the leader in Domestic, Asian and European applications
The contents of MAHLE gaskets are packaged in shrink wrapped tray, giving you the added security of knowing that you have the right parts, prior to opening the package

from

$83.29

Mr. Gasket small block Chevy water pump pulley. Designed for 2 V belts. Chrome plated steel. Stock replacement for long style Chevy water pump. Not designed for under or over driving water pump.

Product Features:

2 Groove Water Pump Pulley
Small Block Chevy Long Style Water Pump
Chrome Plated Steel
Not Designed For Under Or Over Driving Water Pump

from

$17.79

Kit includes thermostat, housing, and all necessary seals/gaskets to do the complete job. These individual parts are manufactured with OEM quality materials and safety standards by an OE Supplier. This thermostat and housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$210.99

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

Thermal tested under real-life temperature simulations
High tensile strength aluminum for maximum crimp strength
Plastic tanks are engineeredáwith integrated ribbingáfor addedástrength to withstand cracks, bowing and distortion during thermal cycles
Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles

from

$65.58

The GMB Water Pump contains no remanufactured components and is designed to combat engine overheating associated with higher RPM, performance and high load applications. All GMB Water Pumps feature a precision ground, heavy duty steel bearing that`s completely sealed and lubricated for life. A specially modified, high performance impeller eliminates cavitation at high RPM`s, maintaining maximum volumetric flow of coolant, thus reducing engine temperature and increasing horsepower.

Product Features:

OE-Equivalent and direct fit application.
100% new with no remanufactured parts.
High flow design
Factory lubricated bearing assembly
Precision ground shaft and hub
OE quality forged housing for maximum coolant flow
Precision built and balanced
Pressed on impeller for increased water flow
Unique no sealed required gasket
Unitized seal protects bearings and provides long life leak free performance.
Factory sealed precision ground one piece bearing assembly

from

$27.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$12.99

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

from

$6.29

GM Genuine Parts Multi Purpose O-Rings are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$272.07

Save time, money and labor with Dorman’s Engine Cooling Fan Assembly. It comes ready to install with the motor, shroud, and blade. Plus, the high fiberglass content offers extra strength and rigidity while improving thermal stability.

Product Features:

Optimal air flow prevents vehicle from overheating
Plug and Play jumper harnesses included (where applicable)
Direct replacement for a proper fit every time
All motors are tested prior to final packaging of fan assembly

from

$117.43

ACDelco GM Original Equipment Engine Cooling Fan Blades are located between the radiator and engine and are GM-recommended replacements for your vehicle’s original components. The fan is a part of the engine cooling system, which moves air across the radiator and A/C condenser to remove heat from the engine cooling system and the AC refrigerant system. The fan may be belt-driven or operated by an electric motor. This cooling fan blade has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$1.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

from

$4.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

from

$211.99

This engine cooling fan assembly is precision-engineered to match the fit and performance of the stock radiator fan on specific vehicle years, makes and models. It has been rigorously tested to ensure it cools as effectively as the original part.

Product Features:

Ideal replacement – this engine cooling fan assembly was precision-engineered to match the fit and performance of the stock radiator fan assembly on specific vehicles.
Complete package – assembly is designed with the same materials and components as the original part.
Quality assured – motors are tested in laboratory settings to ensure performance
Cost effective and reliable – trustworthy manufacturing for far less than same part at the dealership

from

$92.99

Electric fan with 16″ diameter. Imperial electric fans are reversible for push or pull operation and are designed with a thin, aerodynamic profile for applications with limited space.

Product Features:

Rapid-Cool® Thin-Line electric fans
16″ diameter
1,400 CFM
Use as a pusher or puller fan

from

$347.99

Black Magic Electric Fan

from

$34.49

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$29.49

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

Premium quality materials for longer service life
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$17.99

This engine cooling fan motor connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

Direct replacement – this engine cooling fan motor connector matches the appearance and function of the factory hardware on specified applications.
Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience