2011 Chevrolet Express 2500 Drive Shafts and Axles
More 2011 Chevrolet Express 2500 Drive Shafts and Axles
Find your specific 2011 Chevrolet Express 2500 original or aftermarket Drive Shafts and Axles below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 2011 Chevrolet Express 2500 Drive Shafts and Axles
Spicer – Universal Joint (Part No.5-178X)
from
$42.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More
Driveworks – Universal Joint (Part No.DW-331BL)
from
$31.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Spicer – Universal Joint (Part No.5-1350X)
from
$44.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Yukon Gear – R1561Tv Rear Axle Bearing And Seal Kit (Part No.10002)
from
$88.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1561TV axle bearing and seal kit, for Ford and Dodge, TorringtonBrand, 2.985″ OD, 1.700″ ID. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Fits Ford and Dodge applications
- Includes axle bearing and seal
- Torrington Brand
- Services one side
- 2.985″ O.D.
- 1.700″ I.D.
Yukon Gear – GM 9.5" Rear Axle Bearing And Seal Kit (Part No.10003)
from
$108.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1561TV axle bearing and seal kit for semi-floating GM 9.5″, TorringtonBrand, 2.985″ OD, 1.700″ ID. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Fits GM applications
- Includes axle bearing and seal
- Services one side
- 2.985″ O.D.
- 1.700″ I.D.
Yukon Gear – Axle Bearing & Seal Kit For 10.5" GM 14 Bolt Truck (Part No.10036)
from
$178.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit for GM 14T (full-floating). This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Fits GM 10.5″ 14 bolt truck
- Includes inner and outer bearings and races and axle seal
- Services one side
Yukon Gear – Adapter Sleeve Fro GM 11.5" & 10.5" 14 Bolt Truck Yokes To Use Triple Lip Pinion Seal (Part No.41209)
from
$29.99
Product Features:
See More
- Adapter sleeve
- Fits GM 10.5″ 14 bolt truck and GM 11.5″
- Converts to triple lip seal
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1330 U/Joint Size (Part No.41024)
from
$187.99
Yukon replacement yoke for Dana 60 and 70 with a 1330 U/joint size. 3.625″ snap ring span, 1.0625″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects. This is a strap style yoke.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1330 u-joint size
- 3.625″ snap ring span
- 1.062″ cap diameter
- Outside snap ring design
- Strap style
Yukon Gear – Pinion Yoke Dust Shield For Dana 60 & 70 (Part No.33441)
NTN – Wheel Bearing (Part No.K8000345509NTN)
from
$90.54
Wheel Bearing
FAG – Wheel Bearing (Part No.K8000204410FAG)
from
$62.57
Wheel Bearing
Yukon Gear – AxleHubBolt (Part No.33583)
from
$5.99
AxleHubBolt
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6064)
from
$121.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 88-12; GMC 96-12;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1988-2012
- Weight approx: 2 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.60 INCH / 66 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- WITH PLATE
- WITH STUDS
- STYLE: ROUND FRAME
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6071)
from
$92.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CADI 02-06; CHEV 97-12; DODGE 03-06; FORD 11-15; GMC 96-12; NISSAN 04-22;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1996-2022
- Weight approx: 2 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- WITHOUT PLATE
- WITHOUT STUDS
- EXTENDED DUST SHIELD
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)
from
$22.79
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.3780 INCH / 35 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- COMPLETE MOUNT
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6091)
from
$103.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 88-12; GMC 94-12;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1988-2012
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- WITHOUT PLATE
- WITH STUDS
Yukon Gear – 9.5" GM C/Clip (Part No.33081)
Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.946-345)
from
$1421.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.
Product Features:
See More
Product Features:
- Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
- 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
- Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
- Serviceable construction – non-staked universal joints are designed for future serviceability
Dorman – Rear Drive Shaft (Part No.976-040)
from
$1336.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.
Product Features:
See More
Product Features:
- Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
- 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
- Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
- Serviceable construction – non-staked universal joints are designed for future serviceability
Dorman – Rear Drive Shaft: Adjustable (Part No.946-180)
from
$369.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.
Product Features:
See More
Product Features:
- Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
- 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
- Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
- Serviceable construction – non-staked universal joints are designed for future serviceability
Dorman – Rear Drive Shaft (Part No.946-008)
from
$788.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.
Product Features:
See More
Product Features:
- Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
- 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
- Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
- Serviceable construction – non-staked universal joints are designed for future serviceability
Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-637)
from
$1137.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.
Product Features:
See More
Product Features:
- Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
- 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
- Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
- Serviceable construction – non-staked universal joints are designed for future serviceability
National – Bearings (Part No.HM88610)
from
$15.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
National – Bearings (Part No.M88010)
from
$10.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
National – Bearings (Part No.208-SL)
from
$48.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Popular 2011 Chevrolet Express 2500 Drive Shafts and Axles Categories
2011 Chevrolet Express 2500 Drive Shafts and Axles
Maybe you’re in the middle of a full rebuild of that 2011 Chevrolet Express 2500. Maybe you just need a couple of Drive Shafts and Axles. Either way, Advance Auto Parts has 17 different Drive Shafts and Axles in our inventory ranging from $5.29 to $1,421.99. That means you can find the exact parts or products you need to keep that 2011 Chevrolet Express 2500 running smoothly.
Drive Shafts and Axles are only as good as their brand. We stock 6 different brands to make sure you have plenty of trusted parts to choose from for your 2011 Chevrolet Express 2500. Spicer, Anchor, and National are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Drive Shafts and Axles for your 2011 Chevrolet Express 2500, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.
So if you’re in the market for aftermarket Drive Shafts and Axles to keep your 2011 Chevrolet Express 2500 rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Drive Shafts and Axles Brands To Make Your 2011 Chevrolet Express 2500 Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 2011 Chevrolet Express 2500 demands trusted brand parts and products to keep it running. Many trusted brands of Drive Shafts and Axles make up Advance Auto Parts’ inventory, and all are ready to help make your Express 2500 the best it can be. Be sure to browse some of our top Drive Shafts and Axles brands and parts.
Popular Spicer Drive Shafts and Axles
We carry Spicer parts in our stock across Axle Shaft Universal Joints categories, plus more. For a 2011 Chevrolet Express 2500, our most popular Spicer Drive Shafts and Axles include:
Top 2011 Chevrolet Express 2500 Drive Shafts and Axles from Anchor
Anchor products are another trusted brand when it comes to Drive Shafts and Axles for your 2011 Chevrolet Express 2500. Popular Anchor parts include:
FAQs for 2011 Chevrolet Express 2500 Drive Shafts and Axles
What are the most purchased Drive Shafts and Axles for the 2011 Chevrolet Express 2500?
Out of 17 Drive Shafts and Axles for the 2011 Chevrolet Express 2500, the most popular in our inventory are:
from
$103.99
This product is not rated
Center Support Bearing Motor Mount: Center, 1 Piece
Center Support Bearings
from
$29.99
This product is not rated
Adapter Sleeve Fro GM 11.5" & 10.5" 14 Bolt Truck Yokes To Use Triple Lip Pinion Seal
Drive Shaft Slip Yoke Sleeves
