from

$26.99

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Tensile minimum load holds up to 1800 N
All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
Brand may vary by location

from

$2.08

Brake Pad Sensor Cli

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$86.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$885.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit comes with everything you need, from pads, rotors and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Brake rotor, pad & hardware engineered to work together to increase stopping power, improve durability & eliminate dust
Rotors are zinc plated for maximum protection against rust.
Includes 1 Front & 1 Rear Sensor Wire
Buy with confidence from the originator & industry leader of brake kits

from

$22.51

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$14.11

Brake Adjuster

from

$1.35

Nut

from

$482.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit with Powder Coated Calipers comes with everything you need, from pads, rotors, calipers and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. The Powder Coated Calipers not only protect against corrosion, but also really stand out behind your wheels! Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit with Calipers.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
All calipers are powder coated, assembled, and tested in our Chicago, IL facility
Low dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Rotors are zinc plated for maximum protection against rust.
Includes 1 Rear Sensor Wire
Buy with confidence from the originator & industry leader of brake kits

from

$546.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Our Z26 Street Warrior Brake Upgrade Kit is recommended for high performance, high horsepower muscle and modified cars. This kit comes with everything you need for easy installation, including pads, rotors and stainless-steel hardware. The Drilled & Slotted rotors and Carbon-Fiber Ceramic pads combine to provide shorter stops under the most demanding conditions. This PowerStop Z26 Street Warrior Brake Upgrade Kit is the affordable bolt-on upgrade that delivers more than just the braking power you need to rein in all those ponies. With our low-dust and low-noise formula, you’ll spend less time cleaning those wheels and more time enjoying what matters most – the drive.

Product Features:

This complete brake kit has been engineered to handle the increased demand of street-driven muscle cars and performance vehicles
Proprietary Carbon-Fiber Ceramic Z26 brake pads enhance heat dissipation versus a typical ceramic brake pad for better stopping power at high speed
Stainless-steel pad shims resist the increased temperatures common on high performance applications
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Drilled & Slotted performance rotors provide maximum cooling
Bolt-on upgrade for stock brakes, no modifications necessary
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Brake rotor, pad & hardware engineered to work together to increase stopping power & enhance heat dissipation for your performance car
Rotors are zinc plated for maximum protection against rust.
Includes 1 Front & 1 Rear Sensor Wire
Buy with confidence from the originator & industry leader of brake kits

from

$25.99

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

Dependable stopping power
Single layer shim for quiet braking
OE-designed slots and chamfers to reduce noise and vibration
Powder-coated backing plate prevents corrosion

from

$155.99

Using advanced re-engineering materials and processes, our master cylinders match O.E. performance and fitment. New O.E.-quality seals and cups are installed on each unit, ensuring leak-free, long-lasting performance. Cast-iron master cylinders are treate

Product Features:

Only new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Bleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Bores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Cast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Piston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Plastic reservoirs are vacuum-tested to ensure they are leak free.

from

$9.99

Brake Vacuum Pump Ga

from

$15.49

Brakes are designed as a system and all the parts need to work together for best performance. The boot and square cut seals included in our Caliper Repair Kit, ensure that the caliper works as designed during the apply and release cycle.

Product Features:

This part matches Original Equipment (OE) quality specifications
Increases the life span of the brake pads
Restores brakes to like-new performance
Prevents noise and premature wear
Direct replacement for a proper fit

from

$319.99

Rein OE Manufactured Brake Vacuum Pumps are produced in an OE factory to the specifications of the auto maker’s engineers! These brake vacuum pumps come complete with a mounting gasket or seal, depending on the application. Vacuum pumps are used in vehicles with engines that do not produce sufficient vacuum to provide power to the braking system, EGR valves, intake manifold switches, as well as turbocharger actuators and others. A failed or improperly working brake vacuum pump can lead to a reduction in braking power, a reduction in part and/or full load performance, a triggering of check engine light or limp mode, or engine misfires. All Rein brake vacuum pumps are manufactured by an OE manufacturer and are the exact same units that originally came on the vehicle!

Product Features:

Ensures the proper operation of vehicle’s braking as well as all other vacuum dependent systems
Engineered and manufactured by an OE manufacturer
Plug and play replacement for original vacuum pump
Applicable gasket included

from

$284.99

PowerStop Performance Brake Calipers are made specifically with the enthusiast in mind. These calipers bolt directly in place of the stock calipers, and they look and perform great behind stock or custom wheels. PowerStop calipers and the brackets are remanufactured in our Chicago, IL facility and treated with a electrostatic high-temperature red powder-coating. The easy to clean powder coating helps to resist rust and corrosion thus extending the life of your calipers. PowerStop calipers are 100% pressure tested to verify piston operation and prevent any possible leaks from occurring. This insures that every caliper is inspected for quality and safety. PowerStop caliper pairs are expertly assembled using new seals, caliper guide pins, dust boots, bleeder screws, stainless steel brake pad abutment clips and mounting brackets. High temperature EPDM rubber dust boots and premium silicone lubricant is used for a smoother operation and an extended life in extreme conditions. The performance color is a nice touch that really stands out behind your wheels!

Product Features:

All calipers are thoroughly inspected for quality and safety. Pressure tested to prevent leaks.
New seals, caliper guide pins, dust boots, bleeder screws, stainless steel brake pad abutment clips and mounting brackets
High temperature EPDM rubber for extended life.
Premium silicone lubrication provides smoother operation.
The easy to clean powder coating helps to resist rust and corrosion and extends the life of calipers.

from

$95.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$55.99

Carquest Platinum Professional brake pads are a premium alternative to original equipment brake pads that provide superior stopping performance, quieter braking and cleaner wheels. All CQ Platinum Professional brake pads are manufactured by a vertically

Product Features:

Industry-leading number of application specific formulations for maximum performance and extended pad life
On-vehicle testing similar to original equipment tests
Patented 4-Layer HEX Shim Technology provides quiet braking
HEX shim design utilizes aramid fibers, the same fibers used in bulletproof vests, to reduce shim wear
Burnishing compound allows for a faster break-in of pads and rotors
PTFE coated hardware and caliper pin grease included for nearly every application
Wear sensors included on most European applications that require replacement
Powder-coated backing plate prevents corrosion

from

$11.07

The ATE Caliper Guide Pin is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$184.63

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$18.79

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

This part matches Original Equipment (OE) quality specifications
Exact fitment and original replacement
Helps deliver a quieter, more efficient braking system
Low-friction PTFE coating to reduce drag
Manufactured with quality materials to suppress high stress levels

from

$39.99

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

Wearever Brake Shoes come bonded or riveted based on OE design.
Wearever Brake Shoes are coated to prevent rust.
Wearever Brake Shoes are 100% New not remanufactured.
Brand may vary by location

from

$1.85

The ATE Caliper Guide Pin Cover is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$47.99

Disc Brake Pad Wear Sensor

from

$165.99

Carquest Platinum painted brake rotors meet or exceed original equipment (O.E.) specifications, delivering superior stopping power with proper harmonic design and non-directional finish that eliminate noise. Carquest Platinum painted rotors feature RotorShield, a rust-inhibiting barrier that provides up to 5 times more protection than non-painted rotors. The RotorShield barrier is applied to the rotor hat to protect from unsightly rust and help maintain a like-new appearance. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of the pads and rotors. Carquest Platinum painted brake rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Engineered to withstand 120 hours of salt spray testing
Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to preventing warping
Air gap eliminates brake fade and increases pad life
Non-directional finish decreases break-in time

from

$155.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$20.00

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features: