2009 Toyota Corolla Alternators and Starters

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• 100% remanufactured drive clutch assembly ensures lasting performance
• Armatures and commutators are 100% load tested
• New motor lead terminals and solenoid contacts are used to ensure maximum connectivity
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

DENSO remanufactured starters are subjected to rigorous testing; Armatures and field coils are high-voltage tested; commutators are refinished and performance-validated; terminals and fasteners are replaced with high-quality copper components. Every starter is exactingly bench-tested to ensure factory-original performance.

Product Features:

• High-voltage tested armature and field coils to ensure reliable performance
• Premium copper terminals to ensure a clean source of electrical current
• All-new bearings, brushes, and seals
• Maximum cranking torque under all conditions
• Class leaders in size and weight
• Environmentally designed to start in cold and hot weather conditions

DENSO remanufactured starters are subjected to rigorous testing; Armatures and field coils are high-voltage tested; commutators are refinished and performance-validated; terminals and fasteners are replaced with high-quality copper components. Every starter is exactingly bench-tested to ensure factory-original performance.

Product Features:

• High-voltage tested armature and field coils to ensure reliable performance
• Premium copper terminals to ensure a clean source of electrical current
• All-new bearings, brushes, and seals
• Maximum cranking torque under all conditions
• Class leaders in size and weight
• Environmentally designed to start in cold and hot weather conditions

Carquest Professional starters are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new starters are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional starters are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new starters are built with all new components and are 100% triple-tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• All new components are utilized to ensure long service life
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Armatures and commutators are 100% load tested
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-10235
• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• All new components are utilized to ensure long service life
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Armatures and commutators are 100% load tested
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Bosch Premium Starters are designed, built and tested to provide the ultimate in performance and reliability

Product Features:

• Built for extremes! Our new and reman starters and alternators are 100% factory tested to ensure reliable performance, under extremes of heat, cold and high demand
• Our new and reman starters and alternators are designed to perform equal to or better than the original equipment parts, that they replace
• Our new and reman starters and alternators are designed to be identical in fit and performance to original equipment parts
• Our new and reman starters and alternators utilize the latest manufacturing technologies and highest quality parts to ensure the best performance and longest life

Litens Automotive is the original equipment supplier for the 2014-2019 Toyota Corolla with 1.8L Gas (ZR Engine). This replacement pulley is also designed and produced by Litens and is exact in all form, fit, and performance characteristics as the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). Decoupling pulleys are engine specific and should never be interchanged with other types of pulley technology. The Litens OAD type pulley is designed to free-wheel in one direction and, with an internal spring and damping device, softly engage in the opposite direction. The OAD is designed as a sacrificial part of the front-end accessory drive system, protecting other belt driven component as well as the alternator. The correct decoupler pulley ensures smooth, quiet performance as well as increasing vehicle gas mileage. Under normal driving conditions, the original pulley will require replacement in approx. 70,000 – 90,000 miles. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Litens Automotive is the original equipment (O.E.) supplier for this application. This replacement alternator pulley is also designed and produced by Litens and is exact in all form, fit, and performance characteristics as the original equipment part. Decoupling pulleys are engine specific and should never be interchanged with other types of pulley technology. The Litens OAD type pulley is designed to free-wheel in one direction and, with an internal spring and damping device, softly engage in the opposite direction. The OAD is designed as a sacrificial part of the front-end accessory drive system, protecting other belt driven component as well as the alternator. The correct decoupler pulley ensures smooth, quiet performance as well as increasing vehicle gas mileage. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Litens Automotive is the original equipment supplier to Toyota for this decoupling alternator pulley. This replacement pulley is also designed and produced by Litens and is exact in all form, fit, and performance characteristics as the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). Decoupling pulleys are engine specific and should never be interchanged with other types of pulley technology. The Litens OAD type pulley is designed to free-wheel in one direction and, with an internal spring and damping device, softly engage in the opposite direction. The OAD is designed as a sacrificial part of the front-end accessory drive system, protecting other belt driven component as well as the alternator. The correct decoupler pulley ensures smooth, quiet performance as well as increasing vehicle gas mileage. Under normal driving conditions, the original pulley will require replacement in approx. 60,000 – 70,000 miles. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._

Product Features:

• Patented Original Equipment Design.
• Protects the alternator and other front-end accessory drive components.
• Installation instructions included.
• New plastic cap included with the OAD.
• Tools Required – Litens recommends using Miller Special Tools P/N 8433A and a torque wrench.
• Professional mechanics can install this replacement OAD in approximately 1 hour. During alternator replacement, belts, tensioners, and routing pulleys should be inspected.
• 55mm O.D.; 17mm I.D; 50mm width; ribbed running surface for a 7-rib serpentine belt; high-grade steel construction. 17mm Hex bit driver Included for ease of installation.

Litens Automotive is the original equipment supplier for this Ford application. This replacement alternator pulley is also designed and produced by Litens and is exact in all form, fit, and performance characteristics as the original equipment part. Decoupling pulleys are engine specific and should never be interchanged with other types of pulley technology. The Litens OAD type pulley is designed to free-wheel in one direction and, with an internal spring and damping device, softly engage in the opposite direction. The OAD is designed as a sacrificial part of the front-end accessory drive system, protecting other belt driven component as well as the alternator. The correct decoupler pulley ensures smooth, quiet performance as well as increasing vehicle gas mileage. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Litens Automotive is the original equipment supplier for this decoupling alternator pulley to both Chrysler and Toyota. The Litens aftermarket replacement part uses the latest design technology used in the Toyota part, so while maintaining the exact Toyota form, may look different than the Chrysler part being replaced. Therefore the Chrysler part performance is improved versus the original equipment part. The Toyota part maintains the exact form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). Decoupling pulleys are engine specific and can not be interchanged with other types of pulley technology. The Litens OAD type pulley is designed to free-wheel in one direction and, with an internal spring and damping device, softly engage in the opposite direction. The OAD is designed as a sacrificial part of the front-end accessory drive system, protecting other belt driven component as well as the alternator. The correct decoupler pulley ensures smooth, quiet performance as well as increasing vehicle gas mileage. Under normal driving conditions, the original Chrysler pulley will require replacement in approximately 50,000 – 60,000 miles. The original Toyota pulley will require replacement in approximately 100,000 -120,000 miles. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._

Product Features:

• Patented Original Equipment Design.
• Protects the alternator and other front-end accessory drive components.
• Installation instructions included.
• New cap included with the OAD (Always ensure the cap is installed after installation)
• Tools Required – Litens recommends using a Miller Special Tools P/N 8433A for pulley removal and installation.
• Professional mechanics can install this replacement OAD in approximately 1/2 hours. During alternator pulley replacement, belts, tensioners, and routing pulleys should be inspected.
• 55mm O.D.; 17mm I.D.; 42.65mm width; 6-Grooved running surface; High-grade steel construction. 17mm Hex bit driver Included for ease of installation.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Bosch has been a major supplier of new alternators to Original Equipment vehicle manufacturers since 1913. Securing OE certification requires strict adherence to stringent precision and performance criteria. These same exacting criteria are also applied in the manufacturing of all Bosch aftermarket alternators. Bosch Premium Alternators are quality built and 100% factory tested to ensure years of reliable performance, even under the most extreme operating conditions.

Product Features:

• Full-load tested to guarantee compliance with Bosch’s strict performance specifications
• 100% factory tested, units are remanufactured (not rebuilt)
• Built to last – uses high quality materials and the most technologically advanced developments.

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• 100% new OE-quality brushes and bearings are used to ensure long service life
• Rotors and stators are load tested and double insulated for maximum charging performance
• Slip rings are precision polished for maximum brush contact and service life
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Bosch has been a major supplier of new alternators to Original Equipment vehicle manufacturers since 1913. Securing OE certification requires strict adherence to stringent precision and performance criteria. These same exacting criteria are also applied in the manufacturing of all Bosch aftermarket alternators. Bosch Premium Alternators are quality built and 100% factory tested to ensure years of reliable performance, even under the most extreme operating conditions.

Product Features:

• Full-load tested to guarantee compliance with Bosch’s strict performance specifications
• 100% factory tested, units are remanufactured (not rebuilt)
• Built to last – uses high quality materials and the most technologically advanced developments.

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Carquest Professional alternators are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new alternators are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional alternators are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new alternators are built with all new components and are 100% triple tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• All new components are utilized to ensure long service life
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672
• Rotors and stators are load tested and double insulated for maximum charging performance

WAI is a leading parts manufacturer for the aftermarket. You’ll find superior quality and performance on all WAI 100% new alternators and starters as well as generators, motors, voltage regulators, rectifiers and other components.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

This ignition lock cylinder is designed to match the fit, function and performance of the original equipment part on specified vehicles. It is engineered to help restore ignition lock function when an original cylinder is broken or worn out.

Product Features:

• Direct replacement – this ignition lock cylinder matches the fit and function of the original equipment assembly on certain vehicle years, makes and models
• Ideal solution – engineered to help restore and ensure the functionality of the lock cylinder
• Durable construction – designed and manufactured to strict specifications for reliable performance
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.
• 100% end-of-line tested to ensure confidence and product reliability, every time.