2009 GMC Sierra 2500 HD Air Suspension and Kits

The Air Command Standard Duty Dual Electric Air Compressor System Kit Allows You To Adjust Your Air Springs With The Touch Of A Button. It Offers A Built in Air Source For Your Suspension System, Making It Easy To Alter Your Springs To Align With The Load Type And Environment. When Shopping For Air Accessories, You will Find That Firestone Air Command Standard Duty Dual Electric Air Compressor System Kit Is Designed To Have A Couple Of Special Benefits. First, The Air Command Standard Duty Dual Electric Air Compressor System Kit Comes Ready To Install, So You Can Set It Up And Get Back To The Road where You Want To Be. Just Connect A Few Wires To The Compressor And A Few To Your Vehicle. The Air Lines And Wiring Harness Can Be Plugged Into The Same Side Of The Unit For Smoother Routing Of Lines And Power Supply. After The Air Command Standard Duty Dual Electric Air Compressor System Kit Is Properly Installed, You Can Make Pressure Adjustments By Pressing A Single Button. This Air Command Standard Duty Dual Electric Air Compressor System Kit Component Allows For Side To Side Or Front to rear Leveling, Real time Pressure Readout, And Dual Left And Right PSI And Pressure Control Readouts. The Air Command Standard Duty Dual Electric Air Compressor System Kit Easy to read Needle Gauge Can Be Viewed Day Or Night, Without Straining Or Squinting Your Eyes. Prior To Installing The Air Command Standard Duty Dual Electric Air Compressor System Kit, Review The Instructions And Identify All Of The Components To Help Make Sure You Get Maximum Performance From Both Your Air Springs And Air Command Standard Duty Dual Electric Air Compressor System Kit. The Installation Steps Are Different Depending On Whether You are Enhancing An Existing Air Helper Spring System With The Air Command Standard Duty Dual Electric Air Compressor System Kit Or Installing It With A New Air Spring System.

Product Features:

• Individual Air Accessory Components Are Also Available, Including Compressors, Air Tanks, And Mounting Solutions, Providing A Wide Variety Of Air Control Assist Solutions
• Adjust The Ride For Various Load And Road Conditions With A Switch, Remote Or Mobile App
• Provides An Instant Air Source For The Air Helper Springs Or Accessories
• Dual Point Fill (Both Air Springs Fill Independently Of Each Other)
• Light Duty Compressor Specs (120 PSI Max Air Pressure, 9 Percent Duty Cycle, 0.32 CFM)

KYB Strut Mounts eliminate the vibration and noise caused by old, hardened vibration insulators. They optimize suspension performance by offering OE quality replacement components designed for each application. KYB Strut Mounts cushion the impacts from road bumps to reduce the jarring effect, noise and vibration that old mounts transmit into the vehicle. Front bearing plates are the steering pivots and support vehicle weight. They are critical to steering performance and wheel alignment. KYB Strut Mounts and bearing plates have a reputation for providing the highest quality in the industry.

Product Features:

• The highest quality replacement strut mount available
• Optimizes suspension performance by offering Original Equipment quality replacement components designed for each application
• Superior rubber reduces noise, vibration and harshness
• Mount bearings provide smoother steering and help retain front end alignment
• Matched grade studs and nuts

Valvoline MaxLife Multi-Vehicle Automatic Transmission Fluid (ATF) is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life.  Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Long life friction modifiers help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
• High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
• Developed with anti-wear technology to help improve transmission durability
• Advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
• Suitable for 95% of traditional ATFs including Dex/Merc, Mercon LV & Mercon V

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Our units are all pre-aligned & pre-adjusted to save installation time and ensure proper switching.
• A lubricated felt pad that lubricates the cam lobes on the vehicles distributor. This reduces wear on the point set rubbing block, extending the usable life of the part.
• Ventilated where available, tungsten contacts, which run cooler and exhibit less erosion.
• The copper-alloy shunt provides superior resistance to breakage, due to the flexing of the moving arm on the point set. It also significantly increases current conductivity over typical steel, shunts.

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Computer-Aided Design (CAD), laser scanning and 3D printing ¿ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ¿ in the part design process ensures speed-to-market and a precise fit guaranteed.
• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the part design process ensures speed-to-market and a precise fit guaranteed.
• Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
• Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Driveworks® offers a line of aftermarket parts and accessories that are commercially acceptable and competitively priced, which provides professional technicians and DIYers with an affordable alternative for repairs.

Product Features:

• Direct-fit OE replacement ensures ease of installation
• Designed to meet OE performance
• As the leader in commercially acceptable parts, we provide professional technicians with the quality parts they need
• As the leader in commercially acceptable parts, we provide professional technicians with the quality parts they need

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Computer-Aided Design (CAD), laser scanning and 3D printing ¿ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ¿ in the part design process ensures speed-to-market and a precise fit guaranteed.
• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the part design process ensures speed-to-market and a precise fit guaranteed.
• Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
• Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.