2009 Chevrolet Tahoe Performance Engines

The COMP Cams 08-500-8 Xtreme Energy Hydraulic Roller Camshaft is marketed as a street/strip performance upgrade for small block Chevy engines, delivering aggressive mid-range power, crisp throttle response, and reliable drivability.

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Thumpr : High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

“This COMP Cams® HV NSR cam is designed for GM cathedral port 4.8L/5.3L/6.0L powered vehicles. It provides amazing drivability and throttle response while also requiring minimal tuning. Torque is increased across the entire operating range while still producing +69 horsepower at peak. Get the most out of your daily driver truck, SUV or 4×4 without sacrificing street manners. The NSR HV cam will provide a deep rumble with a mild, yet noticeable lope. At .541″” lift, this cam is designed to allow drop-in performance with stock valve springs. Also compatible with stock converters.”

HYDRAULIC – Magnum: Street/strip special, 3000 stall, headers, gears, 9.5:1+ compression. Very rough idle. OR Drag Race: 3000+ stall in heavy car with 10:1+ compression.

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.

This Holeshot 3000 is for all 1998-02 GM Camaro/Firebirds, 1999-06 GM1500 trucks/SUV’s with LS1, 4.8L, 5.3L, or 6.0L engine and 4L60E or 4L65E transmission. This converter retains the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 3000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Will Not fit 1997-05 Corvette. Has both 10.75 and 11.08-inch bolt circles

This Holeshot 2400 fits all 1998-02 GM Camaro/Firebirds w/LS1 engine, 1999-up GM1500 trucks and SUV’s with 4.8L, 5.3L, or 6.0L engine and 4L60E or 4L65E transmission. This converter retains the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2400 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Will Not fit 1997-05 Corvette. Has both 10.75 and 11.08-inch bolt circles.

The Tork Master 2400 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1996 4L60E w/30 spline input transmissions. This converter retains the lock-up feature. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75 in. bolt circle

This Holeshot 2000 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1997 4L60E w/30 spline input, and 1997-04 Corvettes. This converter retains the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace-brazed impeller fins and turbine, a new precision alloy impeller hub, and new heavy-duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate-type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, and less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide, or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

Edelbrock part No: 97384 high performance hydraulic roller lifters for 1987 and later small-block Chevys are the perfect match for Edelbrock Rollin’ Thunder hydraulic roller cams. The Edelbrock Part No: 97384 are a drop-in replacement for 1987 and later blocks that accept factory roller camshafts. These precision hydraulic roller lifters feature tight ID tolerances that allow for better control at higher RPM and a micro finish OD for reduced friction.

COMP Cams Hydraulic Roller Lifters are a performance upgrade for stock hydraulic roller lifters or retro-fit hydraulic roller lifters for non-roller blocks. The roller wheel decreases friction and increases longevity when compared to flat tappet lifters. Hydraulic roller lifters can handle much more aggressive cam profiles than flat tappets unlocking performance potential.

Designed to take advantage of the GM LS engine’s larger camshaft journal diameter, the XFI RPM camshaft line takes Xtreme Energy technology to deliver excellent power.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing drivability and creature comforts, the Xtreme Energy grind family offers gains in torque and horsepower while still delivering adequate vacuum for power brakes and other vacuum dependent accessories. Xtreme Energy camshafts work great in carbureted applications, but offer the best performance with aftermarket intake manifolds, lower gear ratios, headers and free flowing exhaust.

Strong torque, good mileage, for stock to mildly modified engines.

Strong mid-range and top end. Will require headers, gears and stall. Strong Idle. Requires custom tuning.

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

HYDRAULIC – Magnum: Pro Street/bracket, limited street driving. Intake, gears, 3500+ stall. Racy idle. 10.5:1 compression. OR Drag Race: 3500-4000 stall or 4 speed with 11:1+ compression.

“Competition Cams Valve Spring Kit, For Ls 1.310″” Beehive 1 Kt, 26915CS-KIT. ”

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

“With a .625″” maximum lift, these Beehive Valve Springs were designed for hydraulic roller cams in LS1, LS2 and LS6 engines. COMP Cams Beehive Valve Springs deliver increased valve train stability and a much lighter valve train. This is achieved with less spring pressure for better valve control and reduced weight of both the spring and retainer. The unique Beehive shape handles valve train stress more efficiently to eliminate damaging harmonics and increases high RPM horsepower and durability. The oval/multi-arc wire shape places the maximum area of the wire at the point of highest stress to handle valve train stress more efficiently and allow better heat dissipation for longer life. Because of the unique Beehive design, the valve train can handle more RPM and more aggressive cam profiles.”

“This Beehive Valve Spring Kit for LS engines is designed for hydraulic roller cams and includes carefully matched Beehive Springs, steel retainers, locks, seals and spring seats. With a .625″” maximum lift, these Beehive Valve Springs deliver increased valve train stability and a much lighter valve train. This is achieved with less spring pressure for better valve control and reduced weight of both the spring and retainer. The unique Beehive shape handles valve train stress more efficiently to eliminate damaging harmonics and increases high RPM horsepower and durability. The oval/multi-arc wire shape places the maximum area of the wire at the point of highest stress to handle valve train stress more efficiently and allow better heat dissipation for longer life.Kit Includes:26918-16 Beehive Valve Springs774-16 Steel Retainers623-16 7° Steel Valve Locks511-16 Valve Seals4705-16 Spring Seats”