2009 BMW M5 Brake Parts

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

• Each unit is 100% new, providing consistent performance when servicing your brake system
• Easy to transfer for on-the-spot master cylinder bleeding
• Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
• Easy to clean to ensure no cross contamination
• Durability for long lasting performance

This wheel disc hardware kit includes rubber components used to protect the caliper pins or bolts. Worn or cracked rubber components will allow excessive movement of guide pins or bolts.

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

• OE-Equivalent and Direct fit Application
• made of special cast iron with high carbon content
• Provides a higher friction coefficient.
• Resistant to vibrations and noise.
• Contains the same high quality craftsmanship as the original equipment manufacturer.
• Guarantees OE quality performance, durability and fitment.

ATE Original brake pads provide quality friction just like the OE pads they replace, providing customer-pleasing brake performance. With the best mixture of materials on the market and a production process which emphasizes quality all the way through, original ATE brake pads represent the state-of-the-art. In order to prevent noise during braking, highly effective primary and secondary measures are both used on brake pads. Primary measures act directly on the point of friction. Here, the main issue is optimization of the materials used for the relevant parts. In many cases, ATE uses the most effective variant and the best primary measure for noise suppression in the industry: the intermediate layer or underlayer! On the other hand, secondary measures are intended to prevent the structure-borne sound which is produced from reaching the ear of the driver and pedestrians. Secondary measures can generally be divided into four groups: damping plates, damping foils, paints and greases. ATE works with over 150 different mixtures of friction material to ensure that the optimal result is always achieved for any particular application. The friction materials are always being refined and developed for this purpose. The pad material consists of various components which each fulfill different functions during braking

Product Features:

• OE engineered brake system technology assures optimum fit and performance
• Advanced friction vehicle specific formulations
• Reduced dusting and extend pad life
• Application matched premium quality friction grade
• Underlayer design helps reduce noise, vibration and harshness
• Shims, chamfers, slots, wear sensors and other premium features included Original ATE Brake pads – Presentation

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

This disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles
• Ideal solution – this kit provides is a reliable replacement for original hardware that has stripped
• Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

• Meets or exceeds original equipment specifications for performance and durability
• OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
• Application-specific caliper bodies for easy installation
• Brackets included where required, for complete system restoration
• Meets or exceeds original equipment specifications for performance and durability
• OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
• Application-specific caliper bodies for easy installation
• Brackets included where required, for complete system restoration
• OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
• 100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
• New bleeder screws, banjo bolts, and crush washers included for a complete repair
• OE Style, stainless steel pad abutment hardware included
• 100% end-of-line inspection and pressure testing ensures quality and performance
• Caliper finish or coating may vary

Schaeffler has played a crucial role in the development from mechanical to hydraulic clutch release systems. Over many years, Schaeffler has gained extensive expertise in the complete clutch release systems.

Nut

Brake Boosters are a vital part of our TRW Drum Brake and Actuation product range, helping you deliver outstanding quality for your customers. We test our Brake Boosters to every extreme, which means you can deliver a more reliable and consistent performance on the road for the drivers you serve. All motorists now demand durability and resilience from their vehicles, which is why we invest in developing Drum Brake and Actuation products like Brake Boosters that are designed to last for longer. Choosing TRW Brake Boosters is a sure way of improving reliability and safety for your customer. As an OE manufacturer of Brake Boosters we can supply you with exactly the same product quality that we deliver to vehicle manufacturers. Whether you’re dealing with a single or tandem Brake Booster, the instructions we provide are easy to follow, which means fitting is straightforward and simple. You can also be safe in the knowledge that TRW Brake Boosters are as environmentally friendly as possible, because we always use as little heavy metal as possible and recyclable materials whenever we can.

Product Features:

• Original equipment (OE) quality
• Wide range of single and tandem Brake Boosters
• Unique tie-rod design meaning lighter and thinner parts for more efficient performance
• Great coverage, with almost 340 part numbers in the range, so you can serve more customers

The Zimmermann Formula Z brake disc was designed with the aim of teaming simple installation with optimum braking effect under high mechanical and thermal load. The compound brake disc developed by Zimmermann accommodates the increased demands incurred by engine tuning and optimized chassis structures. COAT-Z – Coat-Z is a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Formula Z – Bake Disc – The composite or compound brake disc named Formula Z is suitable for motorsport applications due to its special design. In contrast to the fully cast-iron brake disc, the friction ring (cast iron) and hub (aluminum alloy) are connected by steel pins. The resulting, floating construction reduces the thermal buffering of the friction ring in the operating temperature state substantially, because the friction ring can freely expand under thermal stress (e.g. when braking from high speeds or several consecutive brake applications). The use of aluminium alloy also considerably reduces the unsprung masses on the vehicle. Material quality / high carbon – Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

• Excellent deceleration action and no distortion of friction ring at high temperatures
• Substantial weight saving and therefore less unsprung mass
• Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
• Hot spots prevented by optimized design of ventilation channels
• 1:1 exchange of original disc possible
• Not subject to registration: general ABE certification supplied with disc
• No conversion required for brake tuning

The Zimmermann Formula Z brake disc was designed with the aim of teaming simple installation with optimum braking effect under high mechanical and thermal load. The compound brake disc developed by Zimmermann accommodates the increased demands incurred by engine tuning and optimized chassis structures. COAT-Z – Coat-Z is a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Formula Z – Bake Disc – The composite or compound brake disc named Formula Z is suitable for motorsport applications due to its special design. In contrast to the fully cast-iron brake disc, the friction ring (cast iron) and hub (aluminum alloy) are connected by steel pins. The resulting, floating construction reduces the thermal buffering of the friction ring in the operating temperature state substantially, because the friction ring can freely expand under thermal stress (e.g. when braking from high speeds or several consecutive brake applications). The use of aluminium alloy also considerably reduces the unsprung masses on the vehicle. Material quality / high carbon – Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

• Excellent deceleration action and no distortion of friction ring at high temperatures
• Substantial weight saving and therefore less unsprung mass
• Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
• Hot spots prevented by optimized design of ventilation channels
• 1:1 exchange of original disc possible
• Not subject to registration: general ABE certification supplied with disc
• No conversion required for brake tuning

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

• Reduced cost
• OE Quality
• Complete Kit

Brake Adjuster

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

• Wearever Brake Shoes come bonded or riveted based on OE design.
• Wearever Brake Shoes are coated to prevent rust.
• Wearever Brake Shoes are 100% New not remanufactured.
• Brand may vary by location

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

• Wearever Brake Shoes come bonded or riveted based on OE design.
• Wearever Brake Shoes are coated to prevent rust.
• Wearever Brake Shoes are 100% New not remanufactured.
• Brand may vary by location

The ATE Caliper Guide Pin Cover is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Bowa electronic brake pad wear sensors are engineered and manufactured to original equipment specifications and are designed to withstand the extreme heat generated by the brake pads. The engineers at Bowa make certain that all materials, parts and tolerances meet the same high standards as the OE brake sensors they supply to brake manufacturers and auto makers worldwide.

Product Features:

• Exact Replacement with OE Fittings and Connectors
• Highly Durable and Resistant to Temperatures
• Supplied with OE style electrical connectors
• Bowa is an OE supplier to Brake and Vehicle Manufacturers

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

• Triggers a warning light on the dashboard
• Should be replaced each time the brake pad is replaced
• Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

Highest mechanical stability under load, highest compressive strength and resistance ATE/Continental has been contributing hydraulic brake hose assemblies for the automotive industry since the 1920’s. With an annual production of approximately 40 million brake hose assemblies, ATE/Continental is one of the world leaders in this sector today. As a full brake system supplier, ATE/Continental distinctively places its direct knowledge of overall hydraulic brake design into this product. The complete OEM experience, coupled with the specialized technology of an OE world market leader, uniquely places ATE/Continental near the top for brake hose assemblies with their ATE brand. ATE brake hoses are suitable for all brake fluids (DOT 3, DOT 4, DOT 4 LV, DOT 5.1)

Product Features:

• More than 70 braiding machines for braid production.
• Autoclaves or vulcanizing presses, and automatic surface control for the production of the inner and outer rubber layers.
• Primary use of extruded connectors.
• Test stands and laboratories are abundantly available for assured accuracy in satisfying the rigid criteria of all customer specifications.
• Outstanding quality standards with compliance certifications for FMVSS106 on our ATE brake hose assemblies, as well as ISO 14001 certification for production.
• In-house ATE N standards that exceed the legal requirements. Original ATE Brake hoses – Presentation

Highest mechanical stability under load, highest compressive strength and resistance ATE/Continental has been contributing hydraulic brake hose assemblies for the automotive industry since the 1920’s. With an annual production of approximately 40 million brake hose assemblies, ATE/Continental is one of the world leaders in this sector today. As a full brake system supplier, ATE/Continental distinctively places its direct knowledge of overall hydraulic brake design into this product. The complete OEM experience, coupled with the specialized technology of an OE world market leader, uniquely places ATE/Continental near the top for brake hose assemblies with their ATE brand. ATE brake hoses are suitable for all brake fluids (DOT 3, DOT 4, DOT 4 LV, DOT 5.1)

Product Features:

• More than 70 braiding machines for braid production.
• Autoclaves or vulcanizing presses, and automatic surface control for the production of the inner and outer rubber layers.
• Primary use of extruded connectors.
• Test stands and laboratories are abundantly available for assured accuracy in satisfying the rigid criteria of all customer specifications.
• Outstanding quality standards with compliance certifications for FMVSS106 on our ATE brake hose assemblies, as well as ISO 14001 certification for production.
• In-house ATE N standards that exceed the legal requirements. Original ATE Brake hoses – Presentation

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

• Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
• Tensile minimum load holds up to 1800 N
• All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
• Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
• Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
• Brand may vary by location

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Carquest Platinum Professional brake pads are a premium alternative to original equipment brake pads that provide superior stopping performance, quieter braking and cleaner wheels. All CQ Platinum Professional brake pads are manufactured by a vertically

Product Features:

• Industry-leading number of application specific formulations for maximum performance and extended pad life
• On-vehicle testing similar to original equipment tests
• Patented 4-Layer HEX Shim Technology provides quiet braking
• HEX shim design utilizes aramid fibers, the same fibers used in bulletproof vests, to reduce shim wear
• Burnishing compound allows for a faster break-in of pads and rotors
• PTFE coated hardware and caliper pin grease included for nearly every application
• Wear sensors included on most European applications that require replacement
• Powder-coated backing plate prevents corrosion

Carquest Premium Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

• Application-specific friction formulations provide shorter stopping distances and extended pad life
• Hardware included for most applications, provides better value and
• OE-designed slots and chamfers to reduce noise and vibration
• Multi-layer shim provides near silent braking
• Powder-coated backing plate prevents corrosion

The TRW Premium brake pads are designed and manufacturing to original equipment specifications, assuring superior quality and fit. TRW has introduced Cotec – an innovative coating for its brake pads. Independent tests have proven that Cotec achieves significantly shorter stopping distances than the brake pads of major competitors or even OE, for the first stops after leaving a garage following a brake pad change. In the normal bedding in process there is a period, known as the green behavior of the pad, which occurs at the start of the bedding in process where the friction co-efficient is lower than usual. Drivers can find it difficult to adjust to the difference in performance during these first stops. TRW Cotec brake pads address this issue by improving the contact between the brake disc and pad. The friction material is the most important part of a brake pad. All TRW’s brake pads contain the optimum mix of raw materials from rubber to graphite. TRW has made a significant investment over the years to ensure that we have the perfect mix – and we make it in-house. The ingredients ensure a stable friction coefficient and the safest braking performance in all temperatures, at all speeds and under all conditions. The backing plates used by TRW are designed, patented and produced in-house to OE specification. They are fitted to the friction material with a unique adhesive compound which can withstand high temperatures and resists extremely high shear strengths. TRW places great emphasis on noise reduction and its brake pads are fitted with high quality shims which act as a damper between the friction material and the brake caliper. TRW friction components are not only tested in our NVH (noise vibration harshness) laboratories and also on the road.

Product Features:

• OE-Equivalent and Direct Fit application.
• Include the OE specified shims.
• Low noise and reduced vibrations.
• Formulated to OE Specifications.
• Superior friction qualities.
• Organic blended compound.