from

$1.07

Fuel Injector O-Ring

from

$48.99

CARQUEST MAP sensors are manufactured with critical OEM components to ensure that your engine runs efficiently to reach the best gas mileage on your vehicle.

Product Features:

CARQUEST MAP sensors connectors are exact OE fit to ensure the proper vacuum is maintained to prevent power loss and to minimize internal contamination.
CARQUEST MAP sensors utilize high temperature resistant seals. Damaged seals can directly impact the vehicles fuel-to-air ratio, making it less fuel efficient.
CARQUEST MAP sensors are 100% individually tested for all product functionalities including proper vacuum seal and electrical output.

from

$75.99

The Bosch Fuel Tank Sending Unit is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications for fit, form, and function

from

$12.49

To perform a complete fuel pump replacement, clean the tank every time. Order the Delphi Fuel Tank Cleaning Kit (Part FC01). Remember, the original pump went into a clean fuel tank, to ensure the same level of performance, the new pump should too. 100 ye

Product Features:

Helps avoid premature fuel pump failure
Lint free towel included
Low suds formulation
Removes harmful contaminants from the fuel tank

from

$340.18

The VDO Electric Fuel Pump Assembly meets or exceeds the OE specifications for fit, durability and performance.

Product Features:

OE-Equivalent electric fuel pump
Direct fit for easy installation
OE connections and fittings
Highly efficient turbine design
Designed for quieter operation

from

$16.49

Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.

Product Features:

Passes all state and federal emissions tests
Manufactured from durable, long-life materials
Reduces air pollution with proper sealing and venting
Independently tested for emission control

from

$49.99

The Secondary Air Injection system is an emission control device designed to pump fresh air into the engine exhaust system to reduce harmful emissions and convert the emission into harmless water vapor via a chemical reaction. These systems were used heavily in the pre-catalytic converter emission control period but found some application in vehicles with catalytic converter systems.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$372.99

100 years of OE experience, supplier to the world’s top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.

Product Features:

Capable of delivering fuel at high pressures that can range from 2,000-2,800 PSI
Mechanically driven high fuel flow pump enables rail pressure build up quickly for fast start times
Fuel delivered directly into the engine combustion chamber for increased horsepower and fuel economy
Meets OE specifications

from

$9.99

This relay connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

Direct replacement – this relay connector matches the appearance and function of the factory hardware on specified applications
Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$229.17

Hitachi fuel injectors are manufactured to OE requirements that meet federal emissions and fuel economy standards, and provide exact OE fit for ease of installation. Hitachi injectors are manufactured using internal components that are compatible with alternative fuels or fuel blends, including ethanol mixtures.

Product Features:

Original Equipment Manufacturer
Premium internal components
OE Calibrated impedance
Fine atomized spray reduces emissions

from

$242.10

Intake Manifold Actuator

from

$3.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$5.85

Throttle Body Gasket

from

$65.80

Air hoses and lines for diesel and gasoline engines with additional blow-by for crankcase ventilation. Prefabricated modules in raw and clean air duct using injection-molded elastomer and plastic items, and blow-molded items.

Product Features:

Mount for temperature sensors
Noise damping
Folds and ribs for flexibility and vacuum stability
Molded-on mounts for wires or cables
Integrated flow divider
Integrated positioning and attachment of prefabricated hose clamps
Radial reinforcement for high vacuum stress in tight installation spaces

from

$52.99

Engineered for a perfect fit and plug-and-play installation, this vapor canister purge valve is a direct replacement for the original equipment purge valve. It is critical to the evaporative emissions system and fulfills government requirements.

Product Features:

Direct replacement – this vapor canister purge valve fits and functions like original equipment to ensure proper function of your vehicle’s evaporative emissions system
Quality construction – manufactured from premium materials for a long service life
Excellent value – original equipment quality at a lower price
Quality tested – has undergone testing to ensure proper fit and performance

from

$7.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$32.99

The temperature of various systems must be reported to the engine control module (ECM) as well as other operating system controllers in the vehicle. Coolant temperature, cabin temperature, exhaust temperature and ambient temperature are just a few systems reported by a temperature sensor. The temperature sensor is fed 5 volts by the systems computer, within the sensor housing will be a thermistor, or dropping resistor whose resistance value will change as the temperature surrounding it changes. Changing resistance in the circuit will change the volt signal at the processor indicating the current operating value.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
Application matched components ensures system operation in like new condition.

from

$146.08

Vapor Canister Purge

from

$148.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$37.58

Fuel Pump Tappet

from

$172.99

100 years of OE experience, supplier to the world’s top automakers, OE Heritage and knowledge built into every aftermarket part.

Product Features:

Precisely manufactured internal valves, diaphragms and springs means excellent performance under all engine operating conditions
Quiet operation, no audible regulator noise
Robust diaphragm materials means longer life, improved durability and compatibility with a wide range of fuels
Consistent and predictable fuel pressure throughout system range of control provides great drivability

from

$193.99

100% new; Delphi OE Technology Validated to match the vehicle applications; Manufactured to meet or exceed OE requirements.

Product Features:

Delphi mass air flow sensors are the global benchmark for accuracy and signal noise
Delphi mass air flow sensors feature high quality sensing elements for outstanding performance over a wide range of ambient temperatures
Delphi is a manufacturer of OE mass air flow sensors since their first use over 30 years ago
All parts are calibrated and tested to match the OE part
Probe solution offered wherever possible to reduce repair time by eliminating the need to replace the flow tube.
Delphi OE technology validated to match the vehicle applications

from

$234.99

DENSO Air/Fuel Ratio Sensors are manufactured and tested to the strictest OE standards for unparalleled peformance.; Each component is precision-built for exact replacement+ and a first time fit.; DENSO gives you the right part and the right fit+ the first time.

Product Features:

Specifically designed to meet the increasing demands of today’s engines
100% checked for high temperature signal output, air tightness, continuity, and heat resistance for optimal efficiency and performance
Coated with aluminum oxide to prevent silicone and lead from contacting the ceramic element and damaging the platinum electrode
Double protection cover helps maintain proper unit temperature for quicker response times, which is critical to your vehicle’s fuel efficiency
Manufactured with a rugged stainless steel housing and porous PTFE filter to resist corrosion and contamination

from

$16.05

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

Designed to OE standards for ease of installation
High-quality materials withstand extreme conditions
Undergoes extensive testing to ensure reliability
As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process

from

$384.99

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$247.07

Fuel Pump Control Mo

from

$556.04

Bosch Manifold Absolute Pressure (MAP) Sensors provide accurate air pressure measurement to very fine tolerances for efficient engine performance.

Product Features:

Extremely sturdy design with a special coating for resistance of harmful chemicals inside the intake manifold.
Bosch continually improves its MAP sensor designs with the latest chip technology.
Designed to meet or exceed your vehicle’s original equipment specifications (performance, driveability, economy, emissions)

from

$179.99

Innovative engineering, manufacturing technology and quality control ensure that Spectra Premium fuel tank straps meet or exceed the performance of the original equipment they replace.

Product Features:

Unit is designed to OE fit, form and function requirements accomplished by leveraging our expertise
Direct fit ensures safe, secure fuel tank installation
Product individually packaged and labeled to help reduce product damage prior to installation
Industry leading coverage on straps for plastic tanks
Manufactured with double-layered steel on the mounting brackets for a more robust solution