2007 Chevrolet Monte Carlo Belts and Hoses
More 2007 Chevrolet Monte Carlo Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2007 Chevrolet Monte Carlo, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2007 Chevrolet Monte Carlo Belts and Hoses
Dayco – Acc. Belt Tensioner (Part No.G6001373666DAY)
from
$92.63
Acc. Belt Tensioner
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 25 Inch Length (Part No.87606)
from
$24.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dorman – OE Fix Stainless Steel Fuel Line Kit: 3/8"; 5/16" ID, 1/8"; 1/8" Long (Part No.819-905)
from
$492.99
This replacement fuel line is made to safely transfer fuel and endure in tough underhood and undercar conditions.
Product Features:
See More
Product Features:
- Ready to install – these braided stainless steel over PTFE flexible fuel lines are already cut to specific length for select Chevrolet cars, and include new brackets and factory connectors
- Full length – these lines are made to the correct length for the specified vehicle, but flexible so they’re easier to route than rigid lines, saving replacement time
- Upgraded materials – high-strength, corrosion-resistant braided stainless steel protects PTFE hoses for reliable longevity under all conditions
- Trustworthy quality – engineered and assembled in the United States and backed by decades of aftermarket experience
Dorman – Help – Emissions Tube (Part No.46056)
from
$6.99
Proper crankcase ventilation is key to smooth performance and engine longevity. Made from quality materials to resist cracking and brittleness, this PCV hose replaces a worn or leaking original equipment hose.
Product Features:
See More
Product Features:
- Ideal replacement – this PCV tubing replaces the original tubing on specified vehicle years, makes and models
- Durable materials – this PCV tubing is designed to withstand exposure to extreme temperatures and oil vapors to resist cracking and leaking
- Cost-effective solution – offers original equipment quality at a competitive price
- Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 76 mm Diameter (Part No.900029A)
from
$28.99
This pulley is manufactured by Litens Automotive the original equipment part supplier and the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Heavy duty thermoplastic construction for long life and trouble-free performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by Litens, the largest original equipment tensioner and pulley supplier in the world, to ensure proper form, fit, and performance
- Heavy Duty Glass Reinforced Polymer Pulley for optimized dimensional control and running surface durability
- Installation instructions included.
Dayco – Serpentine Idler/Tensioner Pulley; Polymer, 76mm Dia., 28.7mm Width, 6 Grooves (Part No.89009)
from
$24.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25535)
from
$60.99
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 23.75" Long, 1.50" Diameter (Part No.E70636)
from
$17.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dorman – Fuel Filler Neck Hose (Part No.573-055)
from
$27.49
Fuel filler neck leaking? This replacement fuel filler neck hose is engineered and thoroughly tested to match the original filler neck for specific vehicle years, makes and models for a reliable repair.
Product Features:
See More
Product Features:
- Direct replacement – this fuel filler neck hose is made to match the original equipment part on specific vehicles
- Durable construction – made of fuel-resistant materials to reduce future failure potential
- Regulatory compliant – built to meet emission and inspection standards
- Trustworthy value – backed by team of engineers and quality control experts in the United States
Dorman – Fuel Filler Neck Hose (Part No.573-161)
from
$50.99
Fuel filler neck leaking? This replacement fuel filler neck hose is engineered and thoroughly tested to match the original filler neck for specific vehicle years, makes and models for a reliable repair..
Product Features:
See More
Product Features:
- Direct replacement – this fuel filler neck hose is made to match the original equipment part on specific vehicles.
- Durable construction – made of fuel-resistant materials to reduce future failure potential
- Regulatory compliant – built to meet emission and inspection standards
- Trustworthy value – backed by team of engineers and quality control experts in the United States
Dorman – Idler Pulley (Part No.G6011833488DOR)
from
$16.12
(Pulley Only) Dorman’s Belt Tensioner Pulley is engineered to maintain tension on the serpentine belt for the life of the belt–thereby keeping the alternator charging, the water pump running, and the power steering pump and A/C compressor operating properly. They feature a high-quality double-sealed bearing to resist damage from contaminants. Replacement prevents belt slip and eliminates squeak, squeal or groaning noise associated with a worn belt tensioner pulley.
Product Features:
See More
Product Features:
- Steel or plastic construction for long-lasting durability against heat, shock and corrosion
- Replacement stops squeak, squeal or groaning noise associated with a worn Belt Tensioner Pulley
- Direct replacement for a proper fit every time
- Vehicle try-on testing and rigorous materials testing to ensure high-quality performance
Dayco – Poly Rib Belt Serpentine Belt; 99.02 Long, 6 Rib Count (Part No.5060990)
from
$66.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Poly Rib Belt Serpentine Belt; 69.5 Long, 6 Rib Count (Part No.5060695)
from
$49.49
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Gates – Premium Molded Heater Hose (Part No.19025)
from
$16.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.25" Inside Diameter (Sold by foot) (Part No.28407)
from
$0.99
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Dorman – AT Oil Cooler Hose A (Part No.J2068720024DOR)
from
$53.46
AT Oil Cooler Hose A
Dayco – Bottom Cog V-Belt; 43.5 Inch Long, Exact Fit Premium Quality (Part No.15435)
from
$16.79
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
Driveworks – Poly Rib Belt Serpentine Belt; 27.24 Long, 6 Rib Count (Part No.41013)
from
$5.49
Dayco engineered to conform to high mileage, worn or misaligned drives without a sacrifice in quiet, long-lasting performance. Constructed with Aramid reinforced EPDM compounds, it delivers more than OE required quality… it delivers the solution to troublesome drive problems. Dayco Poly-Rib Belts meet or exceed SAE J1459 and SAE J2432 specifications.
Product Features:
See More
Product Features:
- Aramid noise resistant fibers embedded in the rubber make this belt run quieter in worn or misaligned pulleys
- No-Noise Advanced Design EPDM rubber compound for quiet extended life
Dorman – AT Oil Cooler Hose A (Part No.J2068754499DOR)
from
$26.08
AT Oil Cooler Hose A
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13" Long, 1.31" Diameter (Part No.C71134)
from
$15.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16.50" Long, 1.50" Diameter (Part No.D70649)
from
$30.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 76 mm Diameter (Part No.900722A)
from
$56.99
Litens Automotive is the original equipment (O.E.) supplier of this pulley assembly for General Motors high end vehicle applications. The Litens replacement part meets all form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). This part is manufactured in Canada by Litens to the same exacting specifications as the O.E. part. Heavy duty steel construction for long trouble-free performance. This is a complete pulley ASSEMBLY including the pulley and proper mounting bolt. Designed specifically for Cadillac, Corvette, and Camaro. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the original equipment part supplier to ensure proper form, fit and performance
- Heavy Duty Steel Pulley. Note: Assemblies save time and ensure “like new” performance
- Precision steel stamping with close tolerance ball bearing pocket.
- Electro-deposited coating (e-coat) for superior corrosion resistance.
- Running surface designed and engineered for proper belt tracking.
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter (Part No.900052A)
from
$33.49
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the largest original equipment part suppliers in the world to ensure proper form, fit, and performance
- Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance
- Installation instructions included.
Dorman – Idler/Tensioner Pulley: Specific Fit, Steel, 76 mm Diameter (Part No.419-628)
from
$36.49
This replacement accessory drive belt idler pulley has been engineered to match the function and performance of the original pulley on select vehicle years, makes and models, properly restoring critical vehicle operations.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt idler pulley matches the fit and function of the original equipment pulley on specified vehicles
- Restores performance – fixes a failed, squealing or groaning noise from a worn idler pulley
- Application specific – reverse engineered from the original design on certain vehicle years, makes and models
- Trustworthy quality – backed by team of engineers and quality specialists in the United States
Gates – Premium Molded Coolant Hose (Part No.20687)
from
$31.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 22" Long, 1.50" Diameter (Part No.E70730)
from
$14.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
ACDelco – Professional Molded Coolant Hose (Part No.G2000576631ACD)
from
$30.49
ACDelco Professional, premium aftermarket Molded Coolant Hoses are composed of specially blended materials to help resist electrochemical degradation (ECD), the leading cause of hose failure. They are specially designed, GM OE style factory-molded hoses to fit today’s smaller, tighter-fitting engine compartments. ACDelco Professional Molded Coolant Hoses are temperature rated from -40 degrees Fahrenheit to 275 degrees Fahrenheit (-40 degrees Celsius to 135 degrees Celsius) and are approved for Marine applications. Do not use for fuel or oil transfer applications. These premium aftermarket replacement molded coolant hoses are manufactured to meet or exceed your expectations for fit, form, and function.
Product Features:
See More
Product Features:
- Has a heat and ozone resistant cover to increase the life of the hose
- Comes with a protective sleeve to help duplicate GM OE designs for proper fit and function
- Made of re-engineered materials to resist vacuum collapse and also reduce the need for internal springs in many applications
- Installs without buckling, bending out of shape, or straining at the connection for easy installation
- Inside diameters ranges from 1?4 in to 1 in to fit different types of vehicles
Popular 2007 Chevrolet Monte Carlo Belts and Hoses Categories
2007 Chevrolet Monte Carlo Belts and Hoses
You count on your 2007 Chevrolet Monte Carlo to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 57 Belts and Hoses ranging in price from $0.99 to $492.99, you’re sure to find everything you need for your 2007 Chevrolet Monte Carlo.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 8 different brands like Dayco, Litens, and Gates. 2007 Chevrolet Monte Carlo Belts and Hoses start as low as $0.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 3,266 extensive product reviews on 2007 Chevrolet Monte Carlo Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length with 4.3 stars and Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 7 Inch Length with 4.3 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2007 Chevrolet Monte Carlo below to get started!
Top-Rated Belts and Hoses Brands For Your 2007 Chevrolet Monte Carlo
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2007 Chevrolet Monte Carlo running right for years to come. In our inventory you’ll find brands like Dayco, Litens, Gates, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 2007 Chevrolet Monte Carlo back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2007 Chevrolet Monte Carlo, and some of our most reviewed Dayco parts include:
from
$29.99
(454)
Serpentine Idler/Tensioner Pulley; Steel, 76mm Dia., 31mm Width, Smooth
Belt Tensioner Pulleys
from
$31.99
(88)
Serpentine Idler/Tensioner Pulley; Polymer, 70mm Dia., 28.3mm Width, 6 Grooves
Idler Pulleys
FAQs for 2007 Chevrolet Monte Carlo Belts and Hoses
What are the most purchased Belts and Hoses for the 2007 Chevrolet Monte Carlo?
Out of 57 Belts and Hoses for the 2007 Chevrolet Monte Carlo, the most popular in our inventory are:
from
$28.99
(49)
O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 76 mm Diameter
Idler Pulleys
from
$32.49
(16)
O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 76 mm Diameter
Belt Tensioner Pulleys
from
$25.99
(44)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5" Long, .63" Diameter
Heater Hoses
What are the top-rated 2007 Chevrolet Monte Carlo Belts and Hoses?
Top-rated Belts and Hoses for your 2007 Chevrolet Monte Carlo based on customer reviews/ratings are:
from
$23.49
(14)
Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length
“Hose fit perfectly.”
from
$18.29
(12)
Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 7 Inch Length
“worked great and was in stock!”
from
$15.99
(5)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13" Long, 1.31" Diameter
“Great service”
