2007 Chevrolet C4500 Kodiak Differentials

Product Features:

• Carrier shim kit for Dana Spicer 30 with 30 spline axles

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
• Included are a pinion seal, complete shim kit, marking compound and brush.

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Product Features:

• DANA-80 R/P 4.88 STD MG

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:

• Bearing race driver set
• 21 pieces
• All steel construction

Differential

Yukon Performance steel spool for 8Dana 80 with 37 spline axles, 4.10 & up. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler Dana Spicer 80 with 37 spline axles
• 4.10 and up ratio only
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

NO RETURN HM807046 SET-UP Bearing (1 SINGLE Bearing) for Dana 80 , 11.5AAM , 4.125″ OD .

Product Features:

• Set up bearing
• Fits HM807046 pinion bearing
• Easily slips on and off pinion journal to allow for pinion depth adjustment

Product Features:

• Fits Dana Spicer 80
• Steel

Differential Carrier

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• CARRIER BEARING KIT FRD 10.5″ W/TIM

Product Features:

• Pinion nut washer
• Fits Dana Spicer 80

Ring/Pinion Sets

Dana 70 & Dana 80 standard Open cross pin shaft, one piece case.

Product Features:

• Cross pin shaft
• Fits Dana Spicer 70 and 80

Product Features:

• MINI INSTALL KIT DANA 80

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Yukon replacement yoke for Dana 80 with a 1480 U/joint size. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 80
• 37 spline
• 1480 u-joint size
• 4.188″ snap ring span
• 1.375″ cap diameter
• Outside snap ring design
• Strap style

Product Features:

• Oil baffle
• Fits Dana Spicer 80

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Differential Pinion

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Product Features:

• Outer slinger
• Fits Dana Spicer 80

Replacement pinion nut for Dana 80, 1 7/8″ socket.

Product Features:

• Pinion nut for Dana Spicer 80
• 1 7/8″ socket

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• DANA-80 MASTER BEARING KIT

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

S135 ring gear bolt & nut kit (set of 16 bolts).

Product Features:

• Ring gear bolt and nut kit
• Fits Dana Spicer S135
• Includes 12 bolts and nuts