2006 Toyota Sienna Radiator Hoses

Designed to transfer glycol-based coolants to and from the radiator as well as through other components in the vehicle’s coolant system.

Product Features:

• EpdM tube and cover with synthetic knit reinforcement.
• Meets or exceeds SAE 20R4Ec class d1 specifications as well as many original equipment specifications.
• Resistant to Electrochemical degradation (EcR).
• compatible with most coolants including ethylene glycol and propylene glycol-based coolants, as well as organic acid modified, long life coolants.
• Id Range of 1 to 3 inches and includes intersect hose configurations.
• Temperature range of -40F to +275F (-40c to +135c)

MacKay utilizes leading edge rubber technology and compounds, supported by in-house processes from rubber mixing to final product. This ensures hoses are made to the strict specifications required for the advanced motor vehicles of the 21st century. In vehicles of today, a hose has to be designed to withstand the stresses of modern, more compact but powerful engines that run hotter and at a higher pressure. Other factors include smaller engine compartments with poor heat dissipation, aggressive coolant additives, and stray (electrochemical) current that may be conducting through the cooling system. In short, the smaller but more powerful engines of today work a lot harder than the larger engines that were standard before. More heat is generated, higher burst pressures are required in cooling system components, and hoses have to be made tougher to withstand these demands. MacKay’s research and development chemists have developed new rubber formulations and manufacturing processes that ensure MacKay hoses meet the greater wear and heat demands created by modern engines. Rubber compounds used in automotive hoses today are predominantly synthetic rubber formulation. All MacKay coolant hoses are made from EPDM compounds that are highly resistant to ozone attack. Hoses made from some other rubber compounds may be subject to ozone deterioration.

Product Features:

• Excellent resistance to high temperatures
• Resists chemical attack (oils, fuels etc.)
• Excellent Ozone resistance
• Good resistance to abrasion
• High resistance to vibration

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Radiator Hose

MacKay utilizes leading edge rubber technology and compounds, supported by in-house processes from rubber mixing to final product. This ensures hoses are made to the strict specifications required for the advanced motor vehicles of the 21st century. In vehicles of today, a hose has to be designed to withstand the stresses of modern, more compact but powerful engines that run hotter and at a higher pressure. Other factors include smaller engine compartments with poor heat dissipation, aggressive coolant additives, and stray (electrochemical) current that may be conducting through the cooling system. In short, the smaller but more powerful engines of today work a lot harder than the larger engines that were standard before. More heat is generated, higher burst pressures are required in cooling system components, and hoses have to be made tougher to withstand these demands. MacKay’s research and development chemists have developed new rubber formulations and manufacturing processes that ensure MacKay hoses meet the greater wear and heat demands created by modern engines. Rubber compounds used in automotive hoses today are predominantly synthetic rubber formulation. All MacKay coolant hoses are made from EPDM compounds that are highly resistant to ozone attack. Hoses made from some other rubber compounds may be subject to ozone deterioration.

Product Features:

• Excellent resistance to high temperatures
• Resists chemical attack (oils, fuels etc.)
• Excellent Ozone resistance
• Good resistance to abrasion
• High resistance to vibration

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:

• Has all the quality features of Gates molded coolant hose and similar to OEM specifications
• Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
• EPDM tube, synthetic fiber knit reinforcement, EPDM cover
• Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
• Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• Meets Type EC electro-chemical requirements as specified in SAE J1684

Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• Meets Type EC electro-chemical requirements as specified in SAE J1684

Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• Meets Type EC electro-chemical requirements as specified in SAE J1684

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Premium hose constructed for long service life.

Product Features:

• Good resistance to high temperatures for extended periods of time, which prolongs service life
• Meets SAE 20R3 Standard Wall Class D-2 requirements
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• CAUTION: Do not use for fuel or oil transfer applications
• CAUTION: Do not use for fuel or oil transfer applications
• PLEASE NOTE: Item is priced and sold by the foot. See store for details.

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

This premium Dayco Insulone Heater Hose delivers heated coolant to the heater core with minimal heat loss. The synthetic EPDM rubber compounds and spiral reinforcement gives this hose excellent burst strength, heat resistance, and compatibility with all common coolants and coolant additives. A special compound used in the insulating layer provides an added measure of protection against heat loss. Built with a black cover, this hose is similar to SAE 20R3, Class D-2 with a temperature range of -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C). Note: NOT suitable for fuel or oil transfer.

Product Features:

• Synthetic EPDM rubber compounds and spiral reinforcement provides excellent burst strength and heat resistance
• Compatible with all common coolants and coolant additives
• Insulating layer provides an added measure of protection against heat loss
• Performs well in temperature ranges of -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C)
• PLEASE NOTE: Item is sold and priced by the foot. See store for details.

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture