2006 Mitsubishi Raider Drivetrains

Below you will find various in-demand Mitsubishi Drivetrains, components and accessories for your 2006 Raider. Advance Auto Parts has popular Raider parts like 4WD Components, Drive Shafts and Axles, Universal Joints and more. You’ll also find aftermarket and OEM Drivetrains for other Raider model years including 2007, 2008, 2009 and more. Select a category of 2006 Mitsubishi Raider Drivetrains below and start saving instantly.

Popular 2006 Mitsubishi Raider Drivetrains Categories

Differential Oil

Propeller Shaft Joint Kits

Axle Shaft Universal Joints

U-Joints

Drive Shaft and Axles

Transfer Case Assemblies

Transmission Transfer Case Motors

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Pinion Flanges

Differential Axle Shafts

Bearing Pullers

Axle Shaft Seals

Differential Pinion Pilot Bearings

4WD Switches

U-Joint Centering Yokes

Front Housing Cover Gaskets

Input Shaft Pilot Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Cover Plugs

Rear Axle Shaft Bearings

Differential Ring and Pinions

Differential End Yokes

Drive Shaft Repair Kits

Rear Differential Pinion Bearings

Differential Carrier Bearings

Differential Carrier Bearing Adjusters

Rear Housing Cover Gaskets

Transfer Case Output Shaft Bearings

CV Intermediate Shafts

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Differential Seals

Complete Differentials

Bearing and Seal Overhaul Kits

Differential Drain Plugs

Differential Ring Gear Bolts

Bearing Race Drivers

Input Shaft Seals

Differential Crush Sleeves

Pinion Shaft Seals

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Oil Pump Housing Seals

Axle Shaft Studs

Transfer Case Shift Fork Inserts

Differential Pinion Gear Washers

Output Shaft Pilot Bearings

Differential Clutch Pack Clips

Universal Joint Strap Bolts

Power Take Off Input Shaft Bearings

Essential Drivetrains for 2006 Mitsubishi Raiders

from

$19.99

Snap Ring

from

$632.35

CARDONE Remanufactured Transfer Case Motors are engineered and remanufactured to meet or exceed OEM performance. Built with quality and durability, our Transfer Case Motors are tested to ensure that the torque power needed for this vital product is restored. Original design weaknesses are corrected to make a longer lasting part. A1 CARDONE engineers use the latest in technology and innovation to create high value at a low cost, providing a quality product that both you and your vehicle can rely on.

Product Features:

Each unit is 100% computer tested at 3 points in the manufacturing process to gaurantee performance every time.
Every motor is assembled with the precise amount of lubricant which ensures quiet operation and long life.
Motor magnets are 100% recharged for OE performance and reliability.

from

$511.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$6.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$14.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$173.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Chrysler 9.25″ rear differential. This kit contains carrier bearings and races.

Product Features:

Fits Chrysler 9.25″ rear
Includes carrier bearings and races

from

$239.96

Rugged SKF drive shaft support bearings are built to meet or exceed OE specifications. They are also built on the years of experience that SKF has earned designing and supplying bearings to the world’s largest OE manufacturers. Engineered and manufactured to specific application requirements that deliver precise drive shaft alignment and support. Center support bearings are pre-lubricated and sealed with metal reinforced seals to prevent contamination. Rubber support cushions are manufactured from durable rubber compounds that provide maximum support while isolating the driveline shaft from damaging vibration. Drive shaft support frames are constructed from high quality steel or aluminum that provides additional strength and long life in harsh environments.

Product Features:

OE Quality, fit and performance
Precise driveshaft alignment and support
Pre-lubricated and sealed
Metal reinforced seals to prevent contamination
Manufactured from durable rubber compounds

from

$28.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$50.99

This drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle.
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$57.99

Product Features:

Crush sleeve eliminator kit for GM 8.5″, 8.6″ and Chrysler 9.25″ rear

from

$13.49

Product Features:

Brand may vary by location

from

$158.99

Axle Shaft

from

$185.99

This drive shaft constant velocity (CV) joint is designed to match the fit, appearance and function of the original CV joint on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this drive shaft constant velocity (CV) joint is designed to match the fit, appearance and function of the original CV joint on specified vehicles.
Restores functionality – reliable replacement for an original part that has failed due to collision damage, water infiltration or road debris contamination.
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$263.99

Yukon flange yoke for Chrysler 9.25″. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 9.25″ rear
29 spline
Round companion flange

from

$102.99

Axle shaft damaged or bearings worn out? This axle shaft assembly directly replaces the original equipment on certain vehicles, ready for install right out of the box.

Product Features:

Direct replacement – this axle shaft assembly replaces the original equipment on specific vehicle years, makes and models.
Ready to install – comes pre-assembled for simple installation with no further assembly required.
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$10.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$64.99

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

Side adjuster for Chrysler 9.25″ rear

from

$84.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$10.99

7290 U-joint strap bolt (one bolt only) for Chrysler 7.25″, 8.25″, 8.75″, 9.25″.

Product Features:

U-Joint strap bolt
Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″
7290 u-joint size

from

$9.49

Product Features:

KIT SHIM PINION

from

$23.71

Trans Case Input Sft

from

$10.99

This differential cover plug is designed to match the fit & function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential cover plug matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$15.99

Product Features:

Carrier shim kit for Dana Spicer 30 with 30 spline axles

from

$1566.99

21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:

Bearing race driver set
21 pieces
All steel construction

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$15.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$5.99

AXLE STUD , 2 5/16″ X 9/16-18 .

from

$209.99

Product Features:

Fits Chrysler 9.25″ rear with open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Upgrade your 2006 Mitsubishi Raider with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 2006 Mitsubishi Raider, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Mitsubishi or enhancing its overall performance, Drivetrains are key to keeping your Raider functioning at its best. At Advance Auto Parts, we offer a wide selection of 253 Drivetrains for the 2006 Mitsubishi Raider, designed to meet your needs without breaking the bank. From 4WD Component replacements to Drive Shafts and Axles upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 2006 Mitsubishi Raider at great prices. Our Drivetrains inventory for this model ranges from just $2.29 to $1,582.99, with an average price of $173.21. Our 253 Drivetrains in stock come from 27 trusted brands, so you’re sure to find the right part for your 2006 Mitsubishi Raider without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2006 Mitsubishi Raider, we stock popular OEM and aftermarket Drivetrains from top names like Royal Purple, Moog, Driveworks, and more. Royal Purple Drivetrains start at just $12.99 and boast an impressive 5 stars average rating from customers. Moog and Driveworks also bring quality to the table, with Drivetrains available starting at $4.79, and at an average 4 stars rating. With 3,806 customer reviews and counting, our 2006 Mitsubishi Raider Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2006 Mitsubishi Raider is always ready to roll. We’re committed to providing you with everything you need to keep your Raider in top shape, all in one place. Start shopping confidently below for your 2006 Mitsubishi Raider!

Best-Selling 4WD Components for 2006 Mitsubishi Raiders

Enhance the driving experience in your Mitsubishi with 2 quality 4WD Component components, starting at $84.99.

show more show less

from

$107.99

from

$84.99

Most Popular 2006 Mitsubishi Raider Drive Shafts and Axles

Customize your Mitsubishi with 41 Drive Shafts and Axles products like Drive Shaft and Axles, Axle Shaft Seals, and Axle Shaft Universal Joints, all priced under $1,167.99.

show more show less

from

$35.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$9.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$121.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$389.99

Prop Shaft Drive Shaft

from

$22.79

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
COMPLETE MOUNT

from

$185.99

Direct replacement – this drive shaft constant velocity (CV) joint is designed to match the fit, appearance and function of the original CV joint on specified vehicles.
Restores functionality – reliable replacement for an original part that has failed due to collision damage, water infiltration or road debris contamination.
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$19.99

Snap Ring

from

$14.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$5.79

Product Features:

Brand may vary by location

from

$438.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation.
Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance.
All-new manufacturing – made 100% new, not remanufactured, so there’s no core charge or return hassle
Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience

from

$51.99

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle.
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$17.99

9.25″ Chrysler C/clip, 0.205″ wide for 4137429 axle.

Product Features:

c-clip for Chrysler 9.25″ rear
0.205″ thick

from

$414.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$122.99

Manufactured to be an OE replacement with the addition of eXtreme Duty outer boots designed to withstand extreme low temperatures and resist impact tears. CV axles use 100% new materials and are engineered for ease of installation and long service.

Product Features:

Thermoplastic Outboard Boots
All New Materials
Boots Performance Tested to -50F
Moly-Blend Grease in inner and outer joints

from

$144.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$883.99

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$529.99

Driveshaft – Front

from

$239.96

OE Quality, fit and performance
Precise driveshaft alignment and support
Pre-lubricated and sealed
Metal reinforced seals to prevent contamination
Manufactured from durable rubber compounds

from

$83.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$22.00

SKF’s advanced PTFE oil seal offers optimum performance in extreme temperature and fluid environments. Other benefits of this seal include; reduced friction, longer service life, easier assembly, reduced weight and compact design.

Product Features:

Machined rubber sealing edge provides greater accuracy and consistency, as well as a better sealing surface.
The flanged design allows for easier and proper installation and helps avoid cocking.
The latex bore coat seals the outer diameter leak path and helps compensate for minor bore imperfections.
Extra dust lip helps keep harmful contaminants, such as dirt, out of the bearing and protects against rust and corrosion.

from

$50.99

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle.
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$1167.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1069.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$806.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$774.99

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$763.99

Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation.
Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance.
All-new manufacturing – made 100% new, not remanufactured, so there’s no core charge or return hassle
Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience

from

$727.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$725.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$649.99

Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation.
Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance.
All-new manufacturing – made 100% new, not remanufactured, so there’s no core charge or return hassle
Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience

from

$649.99

Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation.
Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance.
All-new manufacturing – made 100% new, not remanufactured, so there’s no core charge or return hassle
Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience

from

$531.42

Driveshaft

from

$472.03

Driveshaft

from

$446.99

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$339.99

Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation.
Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance.
All-new manufacturing – made 100% new, not remanufactured, so there’s no core charge or return hassle
Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience

from

$281.16

The FEQ Driveshaft is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$219.46

DRIVESHAFT

from

$64.99

BEARING – CRB

from

$44.99

SPICER U-JOINT

from

$13.29

SHAFT SEAL

from

$8.28

Wheel Seal

from

$5.99

AXLE STUD , 2 5/16″ X 9/16-18 .

Top Picks for 2006 Mitsubishi Raider Universal Joints

Upgrade Mitsubishi Raiders with top-quality Universal Joints parts, including 23 OEM and aftermarket selections for your 2006 model.

show more show less

from

$28.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.

from

$39.99

from

$25.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$19.99

Backed by superior materials and rigorous testing, MOOG Heavy Duty universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$15.99

DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$32.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$36.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$7.89

Universal Joint

from

$6.49

Universal Joint

from

$4.59

Universal Joint

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$5.49

Universal Joint – Brute Force

from

$4.49

Universal Joint

from

$37.99

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$263.99

Yukon flange yoke for Chrysler 9.25″. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 9.25″ rear
29 spline
Round companion flange

from

$49.99

7260 U/joint strap, Small Chrysler w/ bolts, 7.25, 8.25, 8.75, 9.25.

Product Features:

u-joint strap kit
Fits Chrysler 7.25″, 8.25″ 8.75″ and 9.25″ rear
7260 u-joint size
Includes two straps and four bolts

from

$36.99

Universal Joint

from

$10.99

7290 U-joint strap bolt (one bolt only) for Chrysler 7.25″, 8.25″, 8.75″, 9.25″.

Product Features:

U-Joint strap bolt
Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″
7290 u-joint size

In-Demand Differentials for 2006 Mitsubishi Raiders

Select from 151 premium Differentials parts for your 2006 Mitsubishi Raider, with prices ranging from $2.29 to $1,566.99.

show more show less

from

$12.99

High Performance Motor Oil API LICENSED MOTOR OIL Royal Purple High Performance Motor Oil combines premium base oils with proprietary additive technologies to create a high performance synthetic engine oil that optimizes performance and protection. Royal Purple High Performance Motor Oils carry the current API and ILSAC engine oil licenses, as well as the GM dexos1 gasoline engine oil approval. ILSAC GF-6 AND GM DEXOS1 Modern gasoline direct injection (GDI) engines have achieved levels of power and fuel economy never before possible in passenger car engines. As a result, smaller engines operate at much higher loads across all engine speeds. This has caused increased wear in critical areas of the engine, and created a destructive phenomenon called low-speed pre-ignition (LSPI). The unique, state-of-the-art additive technology in Royal Purple High Performance engine oils is designed specifically to address these issues, and help engines maintain performance and reliability.

Product Features:

Better Wear Protection
Increased Protection against Low Speed Pre-Ignition
Increased Fuel Efficiency
Better Protection for Vehicle Exhaust Emissions Equipment
Improved Compatibility with Fuels Containing Ethanol
Superior Corrosion Protection
Made in USA

from

$25.99

Max Gear is recommended for truck and automotive differentials, outboard motor lower units or in rear axles or manual transmissions requiring an API fluid. Max Gear is a high performance automotive gear oil designed to provide maximum protection to heavily loaded gears while increasing power throughput through the drive train. Max Gear virtually eliminates both gear and bearing wear-even under severe squeeze film conditions caused by extremely high loads, sudden shock loads or low RPMs. Slippery, synthetic molecules not only reduce wear and friction but significantly increase Max Gear’s cold weather fluidity and lubricity, making it the ideal choice for vehicles operating in cold climates. Gears run smoother, quieter, cooler and longer without overhauls. It is noncorrosive to both ferrous and nonferrous metals.

Product Features:

Maximizes horsepower
Extends gear and bearing life
Reduces operating temperature
Lower coefficient of friction
Superior corrosion protection
Separates rapidly from water
For use with open, limited-slip and locking differential
Contains limited-slip friction modifier
Made in USA

from

$69.99

Valvoline SAE 75W-140 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our formulation provides exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity and wear resistance, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. It’s recommended for conventional rear axles and transmissions requiring EP gear lubes under high speed, high load, high torque and high horsepower conditions.

Product Features:

EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -22F to 390F degrees
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$16.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$5.99

Direct replacement – this differential cover plug matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$8.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$39.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$7.49

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$2.49

Product Features:

CRUSH SLEEVE 7.25 & 8.25 MIN ORDER 5000

from

$202.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

CHRYSLER 9.25 ’01 & UP REAR

from

$67.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles.
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid.
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$384.99

This differential ring and pinion directly replaces the original equipment on specific vehicle years, makes and models.

Product Features:

Direct replacement – this ring and pinion set matches the fit and function of the original components on certain vehicle applications.
Effective fix – eliminates grinding and whining from failed original bearings.
Thoroughly tested – vehicle try-on testing and rigorous quality control measures ensure longevity
Trustworthy quality – backed by team of designers and engineers in the United States

from

$46.99

Cross pin shaft for standard open Chrysler 9.25″, .860″ diameter. Will not fit posi!

Product Features:

Cross pin shaft for Chrysler 9.25″
Fits standard open differentials only
0.860″ diameter

from

$10.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$9.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$6.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$12.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$23.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$5.99

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$65.99

Axle shaft damaged or bearings worn out? This axle shaft assembly directly replaces the original equipment on certain vehicles, ready for install right out of the box.

Product Features:

Direct replacement – this axle shaft assembly replaces the original equipment on specific vehicle years, makes and models.
Ready to install – comes pre-assembled for simple installation with no further assembly required.
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$219.99

Product Features:

C9.25 OPEN INTERNAL KIT, 1984-UP

from

$165.99

Product Features:

CHRYS 9 1/4″ OPEN EMPTY CASE CAN USE ABS RING.

from

$419.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits 2010 and down Chrysler 9.25″ rear
9.25″ ring gear diameter
29 spline pinion
12 ring gear bolts
4.11 ratio

from

$8.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$32.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$19.99

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$2.49

Product Features:

RING GEAR BOLT 8.5″ 7.5″ 7/16 X 20 LEFT HAND

from

$8.99

This differential cover plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential cover plug matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$9.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$12.99

Royal Purple HMX SAE 5W-30 High-Mileage Synthetic Motor Oil, 1 quart is specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles. Formulated with robust zinc/phosphorus anti-wear compounds combined with Royal Purple’s proprietary additive technology Synerlec, HMX is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines. In addition, HMX is fortified with stout detergents to remove engine build-up and deposits, maintain cleanliness and promote engine longevity.

Product Features:

Specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles
Formulated with robust zinc/phosphorus anti-wear compounds combined with royal purple’s proprietary additive technology
Hmx is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines
Reduces friction and metal-to-metal contact for peak engine performance
Also provides outstanding oxidation resistance to safely extend oil drain intervals, and an ionic attraction to metal surfaces, providing protection and minimizing wear at start-up
High-Mileage Formula: Specifically designed for engines with more than 75,000 miles, this full synthetic engine oil helps minimize wear and restore lost performance.

from

$9.99

Ring gear bolt for Chrysler 9.25″ rear, 7/16″ x 18.

Product Features:

Ring gear bolt for Chrysler 9.25″ rear

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$7.49

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles.
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$16.99

Product Features:

Brand may vary by location

from

$159.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Spindle bearing and seal kit
Includes all components required to complete the repair
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$38.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$102.99

Axle shaft damaged or bearings worn out? This axle shaft assembly directly replaces the original equipment on certain vehicles, ready for install right out of the box.

Product Features:

Direct replacement – this axle shaft assembly replaces the original equipment on specific vehicle years, makes and models.
Ready to install – comes pre-assembled for simple installation with no further assembly required.
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$309.99

from

$51.99

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles.
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid.
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$16.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$15.99

Product Features:

Carrier shim kit for Dana Spicer 30 with 30 spline axles

from

$7.99

Product Features:

CHRY 8 3/4″ RING GEAR BOLTS C 8.25″

from

$215.99

CHRYSLER 9.25 ’01 & UP

from

$8.99

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
3/8″ x 24 thread
.866″ long

from

$24.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

Most Sold 2006 Mitsubishi Raider Transfer Cases

Explore our best-selling Mitsubishi parts for the 2006 Raider among 35 OEM and aftermarket options starting from $4.79.

show more show less

from

$15.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$17.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$10.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$25.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$394.99

Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:

Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications.
Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion.
100% new – this transfer case motor is entirely new, not remanufactured like competitors
Quality assured – vehicle-specific application has been validation tested to ensure quality

from

$7.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$4.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$275.99

CARDONE Remanufactured Transfer Case Motors are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. Each unit is 100% computer tested at three points during the remanufacturing process to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance with our direct-replacement transfer case motors.

Product Features:

All motors are 100% torque tested to ensure strength for proper gear engagement.
Each unit is 100% computer tested at 3 points during the remanufacturing process for guaranteed performance.
Every motor is assembled with the precise amount of lubricant to ensure quiet operation and long life.
Motor magnets are 100% recharged for superior performance and reliability.
Transfer case motor sensors are 100% replaced with new, O.E.-quality sensors for superior performance and long product life.
As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.

from

$56.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$25.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$8.49

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$25.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$297.99

TCasePlanetaryCrrier

from

$53.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$26.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$1582.99

Evolution Driveline products, are remanufactured to meet or exceed OEM specifications for quality, fit, and performance. Every transfer case we sell passes a comprehensive battery of tests on our computerized test center. We recreate actual driving conditions and analyze performance before the product even leaves the factory, so you can buy with confidence.

Product Features:

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$1494.99

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$1408.99

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$1292.99

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$1273.99

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$1266.99

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$632.35

Each unit is 100% computer tested at 3 points in the manufacturing process to gaurantee performance every time.
Every motor is assembled with the precise amount of lubricant which ensures quiet operation and long life.
Motor magnets are 100% recharged for OE performance and reliability.

from

$263.99

Transfer Case Motor

from

$189.99

TCaseBrg-SealKit

from

$151.99

TCaseBrg-SealKit

from

$49.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$45.49

SHAFT SEAL

from

$24.29

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$23.71

Trans Case Input Sft

from

$21.29

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$19.29

Multi Purpose Sel Rg

from

$15.49

BEARING

from

$13.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$11.99

TCaseShiftForkInsert

from

$11.29

CUP

Top-Rated Drivetrains Brands For Your 2006 Mitsubishi Raider

Shop for the best-rated brands offering Drivetrains and other products for your 2006 Mitsubishi Raiders. Below you’ll find some of our best rated Drivetrains from Royal Purple, Moog, and Driveworks, and more. Drivetrains from these brands that fit a 2006 Raider start at just $4.79 and are rated as high as 5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Royal Purple 2006 Mitsubishi Raider Drivetrains

When it comes to maintaining or upgrading your 2006 Mitsubishi Raider, using quality Drivetrains is essential to ensure durability and a perfect fit. Royal Purple ticks all of those boxes. We offer a wide selection of Royal Purple Drivetrains, specifically designed for the 2006 Mitsubishi Raider. With over 3 Royal Purple brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $12.99, with an average price of just $17.32. Plus, with over 139 customer reviews and an average rating of 5 stars, you can trust that our Royal Purple Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$25.99

(57)

MaxGear SAE 75W140 High Performance Gear Oil w/Friction Modifier Additive, 1 QT

“Good Quality and OK price!”

from
$12.99

(82)

High Performance SAE 5W30 Synthetic Motor Oil, API Certified, 1 QT

“best oil”

from
$12.99

This product is not rated

HMX SAE 5W-30 High-Mileage Synthetic Engine Oil (1 Quart)

“”

Popular Moog 2006 Mitsubishi Raider Drivetrains

Moog auto parts is one of the highest quality Drivetrain brands in the market. Any 2006 Mitsubishi Raider owner should feel confident when installing genuine Moog parts in their vehicle. To ensure the best fit and performance for your 2006 Raider, Advance Auto Parts carries a full inventory of 6 Moog Drivetrains. Plus you will be keeping your Mitsubishi in peak condition while saving money because prices on these Moog Drivetrains range from $19.99 to $36.99, plus, with more than 355 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from
$32.99

(30)

Non-Greaseable Super Strength Universal Joint

“Working great.”

from
$19.99

(82)

Greaseable Premium Universal Joint

“Great product”

from
$25.99

(143)

Greaseable Premium Universal Joint

“Good product”

FAQs for 2006 Mitsubishi Raider Drivetrains

Which Drivetrains are best-sellers for 2006 Mitsubishi Raiders?

Out of 253 Drivetrains that fit 2006 Mitsubishi Raiders, the following parts are the top sellers:

Greaseable Premium Universal Joint (10086740) – $25.99
Greaseable Premium Universal Joint (10086900) – $19.99
Universal Joint (10265714) – $15.99

What’s the price range for 2006 Mitsubishi Raider Drivetrains?

Drivetrain prices for the 2006 Mitsubishi Raider start at $2.29 and go up to $1,582.99 for the most premium parts.

What’s the average price of a Drivetrain for a 2006 Mitsubishi Raider?

The average price for Drivetrains for the 2006 Mitsubishi Raider is $173.21. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Mitsubishi Raider model years?

Yes, we currently carry Drivetrains for 3 model years of Mitsubishi Raiders between 2007 and 2009. Drivetrains are bought most frequently for the following model years: 2009, 2008, and 2007.

What are the cheapest Drivetrains for my 2006 Mitsubishi Raider?

The cheapest 2006 Mitsubishi Raider Drivetrains we carry in stock are:

Differential Crush Sleeve (20520218) – $2.29
Ring Gear Bolt (20520168) – $2.49
Differential Crush Sleeve (20520219) – $2.49
Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (11643194) – $3.99
Differential Plug 3/4 Inch Rubber (22145314) – $3.99

What are the top-rated Drivetrains that fit the 2006 Mitsubishi Raider?

Out of 3,806 reviews by customers, our 2006 Mitsubishi Raider Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 2006 Mitsubishi Raider and their top-rated products:

Differentials
- Differential Plug, Rubber (17190157) – $5.99
- Differential Cover Assembly (11340637) – $67.99
- Differential Crush Sleeve (20520219) – $2.49
Universal Joints
- Differential Plug, Rubber (17190157) – $5.99
- Differential Cover Assembly (11340637) – $67.99
- Differential Crush Sleeve (20520219) – $2.49

What types of Drivetrains do you sell for my 2006 Mitsubishi Raider?

As of 2/5/25, these are some of the most in-demand types of Drivetrains for a 2006 Mitsubishi Raider:

Can I get help with 2006 Mitsubishi Raider Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Mitsubishi Drivetrains and more.

What is your return policy for Mitsubishi Raider Drivetrains?

Advance Auto Parts keeps returns simple. For new Mitsubishi Raider Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

2006 Mitsubishi Raider Drivetrains

Yukon Gear – Snap Ring (Part No.33578)

A1 Cardone – Remanufactured Transfer Case Motor (Part No.J7100895317CAR)

Powertrax – Grip LS Traction System (Part No.LS309231)

Felpro – DIFFERENTIAL GASKET (Part No.RDS 55047)

National – Bearings (Part No.B-228)

Yukon Gear – Carrier Installation Kit For Chrysler 9.25" Rear Differential (Part No.57001)

SKF – Driveshaft Support with Bearing (Part No.K1030285149SKF)

National – Shaft Repair Sleeve (Part No.99225)

Dorman – Drive Shaft Repair Kit – Only Fits Dorman Driveshafts (Part No.932-984)

Yukon Gear – Crush Sleeve Eliminator Kit For GM 8.5" & Chrysler 9.25" (Part No.55048)

Driveworks – Tapered Roller Bearing (Part No.S-LM-102911)

Yukon Gear – Axle Shaft (Part No.21847)

Dorman – Propeller Shaft CV Joint Kit (Part No.932-303)

Yukon Gear – Flange Yoke For Chrysler 9.25" (Part No.41012)

Dorman – Front Axle Shaft (Part No.630-415)

Motive Gear – Differential Pinion Seal (Part No.8516N)

Yukon Gear – Differential Side Bearing Screw Adjuster For 9.25" Chrysler (Part No.33256)

Carquest Premium – 4WD Switch (Part No.FWC1024)

Yukon Gear – 7290 U-Joint Strap Bolt (One Bolt Only) For Chrysler 7.25", 8.25", 8.75", 9.25" (Part No.33246)

Motive Gear – Differential Pinion Shim Kit (Part No.1102)

SKF – Trans Case Input Sft (Part No.J7120366723SKF)

Needa Parts – Rubber Differential Plug Chrysler 2008-2000 (sold by each) (Part No.090-062)

Yukon Gear – Replacement Carrier Shim Kit For Dana Spicer 44, 30 Spline Axles (Part No.55010)

Yukon Gear – Bearing Race Driver Set, 21 Piece (Part No.56030)

Yukon Gear – The Carrier Bearing Puller (Part No.56072)

National – Bearings (Part No.M88048)

Yukon Gear – Axle Stud , 2 5/16" X 9/16-18 (Part No.33556)

USA Standard Gear – Open Spider Gear Set For Chrysler 9.25", 31 Spline (Part No.39004)

Carquest Premium – 4WD Switch (Part No.FWC1047)

Carquest Premium – 4WD Switch (Part No.FWC1024)

Spicer – Universal Joint (Part No.5-1310X)

National – Multi Purpose Seal (Part No.710489)

Carquest Premium – CV Axle Shaft Assembly (Part No.NCV12187)

CRS – Prop Shaft Drive Shaft (Part No.N91519)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

Dorman – Propeller Shaft CV Joint Kit (Part No.932-303)

Yukon Gear – Snap Ring (Part No.33578)

National – Bearings (Part No.B-228)

Driveworks – Axle Shaft Seal (Part No.S-710489)

Dorman – Front Drive Shaft: Greaseable, Adjustable, OE Fix (Part No.938-014)

Dorman – Drive Shaft Repair Kit – Only Fits Dorman Driveshafts (Part No.932-988)

Yukon Gear – 9.25" Chrysler C/Clip (Part No.33075)

Cardone – Drive Shaft: Not Greasable, Direct Replacement (Part No.65-9151)

Carquest Premium – Extreme Duty CV Axle (Part No.NCV12187XD)

National – Multi Purpose Bearing (Part No.HB-88530)

Yukon Gear – The Carrier Bearing Puller (Part No.56072)

USA Standard Gear – Driveshaft – Front (Part No.44068)

SKF – Driveshaft Support with Bearing (Part No.K1030285149SKF)

National – Bearings (Part No.110-L)

SKF – Axle Seal (Part No.K4021286879SKF)

Dorman – Drive Shaft Repair Kit – Only Fits Dorman Driveshafts (Part No.932-984)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.936-011)

Dorman – Rear Drive Shaft: Greaseable, Adjustable (Part No.976-631)

Dorman – Rear Drive Shaft (Part No.936-010)

Cardone – Drive Shaft: Not Greasable, Direct Replacement (Part No.65-3020)

Dorman – Front Drive Shaft: Greaseable, Adjustable, OE Fix (Part No.938-013)

Dorman – Rear Drive Shaft (Part No.936-180)

Dorman – Rear Drive Shaft: Adjustable (Part No.976-776)

Dorman – Front Drive Shaft: Greaseable, Adjustable, OE Fix (Part No.938-011)

Dorman – Front Drive Shaft: Greaseable, Adjustable, OE Fix (Part No.938-010)

Autopart International Inc – Driveshaft (Part No.K10001929657API)

Autopart International Inc – Driveshaft (Part No.K10001932746API)

Cardone – Drive Shaft: Not Greasable, Direct Replacement (Part No.65-9514)

Dorman – Front Drive Shaft: Greaseable, Adjustable, OE Fix (Part No.938-012)

FEQ – New Driveshaft (Part No.K1000466752FEQ)

Worldpac – DRIVESHAFT (Part No.K1000895432CAR)

FAG US – BEARING – CRB (Part No.102549)

Spicer – SPICER U-JOINT (Part No.5-1310-1X)

FAG US – SHAFT SEAL (Part No.SS2425)

Autopart International Inc – Wheel Seal (Part No.K80102008285API)

Yukon Gear – Axle Stud , 2 5/16" X 9/16-18 (Part No.33556)

Spicer – Universal Joint (Part No.5-153X)

Spicer – Universal Joint (Part No.5-213X)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)

Driveworks – Universal Joint (Part No.DW-354)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)