2006 Kia Sorento Belts and Hoses
More 2006 Kia Sorento Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2006 Kia Sorento, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2006 Kia Sorento Belts and Hoses
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 12 1/2 Inch Length (Part No.88491)
from
$15.79
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.18873)
from
$25.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 9.50" Long, .63" Diameter (Part No.B70873)
from
$10.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999668A)
from
$138.99
This genuine Litens belt tensioner is supplied by the original equipment tensioner supplier and meets all form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). As with the original equipment part, this tensioner is manufactured in Korea for these Hyundai/Kia applications. Manufactured with an O.E. specified heavy duty steel pulley. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the original equipment part supplier to ensure proper form, fit and performance
- Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
- Durable Steel/Smooth Pulley for long service life and performance.
- Installation instructions included
Original Equipment – Accessory Belt Tensioner Assembly (Part No.G6001304906OEA)
from
$374.87
The Original Equipment Accessory Belt Tensioner Assembly is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application
- High quality precision spring tension assembly
- OE specified bearing and pulley assembly
- Durable long life performance
Dorman – Automatic Belt Tensioner (Tensioner Only) (Part No.419-004)
from
$217.99
This accessory drive belt tensioner assembly is designed to match the fit of an original equipment assembly on specified vehicles. It is engineered to help ensure proper belt tension when an original belt is slipping, broken, or worn from fatigue.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt tensioner assembly is designed to match the fit of an original equipment assembly on specified vehicles
- Ideal solution – engineered to help ensure proper belt tension when an original belt is slipping, broken, or worn from fatigue
- Durable construction – designed and manufactured to strict specifications for reliable performance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 22.5" Long, 1.38" Diameter (Part No.E72533)
from
$25.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10.25" Long, 1.31" Diameter (Part No.B71149)
from
$16.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Radiator Hose (Part No.G2000927813DAY)
from
$12.59
Radiator Hose
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 62 mm Diameter (Part No.900540A)
from
$67.99
This Litens pulley is manufactured by the original equipment part supplier to Hyundai. This pulley is produced for serpentine belt routing applications on the 2.4L Hyundai (power steering). The Litens replacement part meets all form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). As with the O.E. part, the replace part is made in Korea using the O.E. specified materials and design and meets all performance and durability requirements. Applications include both Hyundai and Kia vehicles. This is the complete assembly including the pulley, mounting bolt, and washer. Crosses to OE# 25288 25001 and others Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the original equipment part supplier to ensure proper form, fit and performance
- Heavy Duty Plastic Pulley with close tolerance ball bearing pocket and precision surface control.
- Includes all mounting hardware – Bolt and large metal dust shield.
- Pulley Assemblies save time and ensure “like new” performance
- Running surface designed and engineered for proper belt tracking.
- 62.0mm O.D.; 17.0mm I.D.; 29.0mm width, grooved 6 rib running surface, high grade polymer construction. Includes Bolt, Dust Shield, and Retainer.
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter (Part No.900501A)
from
$62.99
INA is the original equipment (O.E.) supplier of this idler pulley used on a wide variety of Kia/Hyundai gas engine applications. The Litens replacement part (supplied by INA) meets all form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). This part is manufactured in Korea to the same exacting specifications as the O.E. part using a heavy duty steel construction for long trouble-free performance. A new bearing duct-cap is included. Most common O.E. part number: 25286-3C100 Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the original equipment part supplier to ensure proper form, fit and performance
- Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance.
- Precision steel stamping with close tolerance ball bearing pocket.
- Electro-deposited coating (e-coat) for superior corrosion resistance.
- Running surface designed and engineered for proper belt tracking.
- 70mm O.D.; 10.1mm I.D.; 27mm width. Smooth running surface, Heavy Duty Steel construction
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter (Part No.900243A)
from
$94.99
This pulley is supplied by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This heavy duty steel pulley conforms to original equipment material and tolerances specifications and meets performance and durability requirements. Fits tensioner and idler applications including Kia/Mitsubishi/Dodge. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the world’s largest Original Equipment suppliers of accessory drive tensioners and pulleys
- Heavy Duty Steel Pulley
- Precision steel stamping with close tolerance ball bearing pocket.
- Electro-deposited coating (e-coat) for superior corrosion resistance.
- Running surface designed and engineered for proper belt tracking.
Bando – Precision Engineered V-Belt (Part No.W10001342404BAN)
from
$23.82
Bando has been manufacturing rubber products for over 100 years. Bando is the OEM supplier to over 80 percent of the top 10 cars sold in the U.S. (by volume). Bando belts are made with EPDM rubber which adheres to OEM specification that is more heat resistant and long lasting. With 19 plants worldwide, Bando are the 3rd largest manufacturer of automotive drive belts in the world. Bando’s automotive belts, serpentine, timing and V-belts are engineered to meet the unique requirements of today’s high performance engines for applications that run the gamut from international racing teams to light duty trucks. Bando manufactures belts for the world’s leading automakers, supplying both OEM and aftermarket applications, all to the same exacting standards of quality.
Product Features:
See More
Product Features:
- Designed to provide the positive no-slip drive requirements needed on demanding overhead cam applications
- Precision molded teeth are protected by durable fabric facing for long life
- Tensile cord is engineered and tested for maximum load carrying capabilities
- Rubber backing resists abrasion, oil and heat
Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100094011MBL)
from
$22.60
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
Bando – Multi Rib (Serpentine) Belt (Part No.W100087561BAN)
from
$24.91
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Strong tensile cords limit stretching.
- Supports higher horsepower loads.
- Made from high strength synthetic rubber.
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Gates – DriveAlign½ Belt Drive Idler/Tensioner Pulley (Part No.38018)
from
$25.99
Product Features:
See More
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
Dayco – Serpentine Idler/Tensioner Pulley; Polymer, 65mm Dia., 24.5mm Width, Smooth (Part No.89161)
from
$20.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear & tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today.
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter (Part No.900239A)
from
$102.99
This Litens belt-tensioning pulley is supplied by one of the largest automotive pulley suppliers in the world and meets all form, fit, and performance characteristics of the original equipment part . Like the Original Equipment (O.E.) pulley, the Litens replacement part is constructed of heavy duty steel for long life and trouble free performance. This pulley is manufactured in Korea for both O.E. and aftermarket Kia applications. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the world’s largest Original Equipment suppliers of accessory drive tensioners and pulleys
- Heavy Duty Steel Pulley
- Precision steel stamping with close tolerance ball bearing pocket.
- Electro-deposited coating (e-coat) for superior corrosion resistance.
- Running surface designed and engineered for proper belt tracking.
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length (Part No.80402)
from
$23.49
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Dayco – Poly Rib Belt Serpentine Belt; 42.52 Long, 6 Rib Count (Part No.5060425)
from
$25.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Gates – V-Ribbed Serpentine Belt: 67.801" Long, 6 Rib Count, Exact Fit (Part No.K060672)
from
$42.99
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.
Product Features:
See More
Product Features:
- Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
- EPDM rubber constructions resist cracking on the rib surface
- Meets or exceeds all specifications from the Original Equipment Manufacturer
- Tensioner Replacement is Recommended (if equipped)
- Unique form grinding of each individual belt assures precise dimensional control.
- Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
Dayco – Poly Rib Belt Serpentine Belt; 37.01 Long, 4 Rib Count (Part No.5040370)
from
$32.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Poly Rib Belt Serpentine Belt; 101.58 Long, 6 Rib Count (Part No.5061015)
from
$43.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Stretch Serpentine Belt; 31.26 Long, 3 Rib Count, Zip Tie Required (Part No.3PK794EE)
from
$42.99
Dayco ela self-tensioning belts incorporate a wear-resistant EPDM rib material, along with a highly elastic EPDM cushion rubber that surrounds the polyamide tensile cord, thus providing the required adhesion & flexibility to maintain lasting performance. The backbone behind the Dayco ela self-tensioning belt is its polyamide tensile member, which allows the high elongation required for installation, yet provides the proper tension maintenance properties to transmit the accessory loads demanded for the drive.
Product Features:
See More
Product Features:
- Designed for two- to four-point drives that do not require automatic or manual tensioning.
- Provides self-tensioning capabilities required by specific OE drives designed for a stretch’ belt
- Elasticity allows for long-lasting performance and proper tension
- Elasticityáallows for long-lasting performance and proper tension
Gates – V-Ribbed Serpentine Belt: 75.346" Long, 6 Rib Count, Exact Fit (Part No.K060747)
from
$50.99
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.
Product Features:
See More
Product Features:
- Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
- EPDM rubber constructions resist cracking on the rib surface
- Meets or exceeds all specifications from the Original Equipment Manufacturer
- Tensioner Replacement is Recommended (if equipped)
- Unique form grinding of each individual belt assures precise dimensional control.
- Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
Driveworks – Poly Rib Belt Serpentine Belt; 97.5 Long, 6 Rib Count (Part No.975K6)
from
$31.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Popular 2006 Kia Sorento Belts and Hoses Categories
2006 Kia Sorento Belts and Hoses
You count on your 2006 Kia Sorento to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 28 Belts and Hoses ranging in price from $10.79 to $229.99, you’re sure to find everything you need for your 2006 Kia Sorento.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 10 different brands like Dayco, Driveworks, and Imperial. 2006 Kia Sorento Belts and Hoses start as low as $10.79!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 122 extensive product reviews on 2006 Kia Sorento Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Curved Radiator Hoses: EPDM Rubber, Standard Duty, 24.5" Long, 1.34" Diameter with 5.0 stars and O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter with 2.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2006 Kia Sorento below to get started!
Top-Rated Belts and Hoses Brands For Your 2006 Kia Sorento
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2006 Kia Sorento running right for years to come. In our inventory you’ll find brands like Dayco, Driveworks, Imperial, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 2006 Kia Sorento back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2006 Kia Sorento, and some of our most reviewed Dayco parts include:
FAQs for 2006 Kia Sorento Belts and Hoses
What are the most purchased Belts and Hoses for the 2006 Kia Sorento?
Out of 28 Belts and Hoses for the 2006 Kia Sorento, the most popular in our inventory are:
from
$16.79
(1)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10.25" Long, 1.31" Diameter
Lower Radiator Hoses
from
$33.49
This product is not rated
Molded Heater Hose: Aluminum/Rubber, OE Fix, Upgraded Material
Heater Hoses
What are the top-rated 2006 Kia Sorento Belts and Hoses?
Top-rated Belts and Hoses for your 2006 Kia Sorento based on customer reviews/ratings are:
from
$38.99
(4)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 24.5" Long, 1.34" Diameter
“good”
from
$94.99
(1)
O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 90 mm Diameter
“Seemed out of balance or wobble really slight”
