2005 Subaru Impreza Belts and Hoses

Essential 2005 Subaru Impreza Belts and Hoses

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 14 1/2 Inch Length (Part No.87966)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 14 1/2 Inch Length

from

$28.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Premium Molded Heater Hose (Part No.18453)

Premium Molded Heater Hose

from

$21.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dorman – Drive Belt Idler Pul (Part No.W1002751291DOR)

Drive Belt Idler Pul

from

$40.10
Drive Belt Idler Pul

Gates – Premium Molded Coolant Hose (Part No.22494)

Premium Molded Coolant Hose

from

$29.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25474)

Vulco-Flex½ II Flexible Coolant Hose

from

$26.99
Product Features:
  • Improved sealing surface for greater leak resistance
  • High flexibility for easy installation
  • Maximum vehicle coverage with minimum inventory
  • Resistant to heat, oil and ozone
  • Rated for SAE 20R5 Class D-2 performance
  • Temperature Range: up to +257 Deg. F (+125 Deg. C)
  • Note: Gates recommends replacing clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Straight Heater Hose: EPDM, Direct Fit, 0.625" Inside Diameter (Sold by foot) (Part No.28411)

Straight Heater Hose: EPDM, Direct Fit, 0.625" Inside Diameter (Sold by foot)

from

$1.49
Premium hose constructed for long service life.

Product Features:
  • Good resistance to high temperatures for extended periods of time, which prolongs service life
  • Meets SAE 20R3 Standard Wall Class D-2 requirements
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • CAUTION: Do not use for fuel or oil transfer applications
  • CAUTION: Do not use for fuel or oil transfer applications
  • PLEASE NOTE: Item is priced and sold by the foot. See store for details.
See More

MacKay – MacKay Radiator Hose (Part No.G200031445MKY)

MacKay Radiator Hose

from

$16.15
MacKay utilizes leading edge rubber technology and compounds, supported by in-house processes from rubber mixing to final product. This ensures hoses are made to the strict specifications required for the advanced motor vehicles of the 21st century. In vehicles of today, a hose has to be designed to withstand the stresses of modern, more compact but powerful engines that run hotter and at a higher pressure. Other factors include smaller engine compartments with poor heat dissipation, aggressive coolant additives, and stray (electrochemical) current that may be conducting through the cooling system. In short, the smaller but more powerful engines of today work a lot harder than the larger engines that were standard before. More heat is generated, higher burst pressures are required in cooling system components, and hoses have to be made tougher to withstand these demands. MacKay’s research and development chemists have developed new rubber formulations and manufacturing processes that ensure MacKay hoses meet the greater wear and heat demands created by modern engines. Rubber compounds used in automotive hoses today are predominantly synthetic rubber formulation. All MacKay coolant hoses are made from EPDM compounds that are highly resistant to ozone attack. Hoses made from some other rubber compounds may be subject to ozone deterioration.

Product Features:
  • Excellent resistance to high temperatures
  • Resists chemical attack (oils, fuels etc.)
  • Excellent Ozone resistance
  • Good resistance to abrasion
  • High resistance to vibration
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13.5" Long, 1.47" Diameter (Part No.E72304)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13.5" Long, 1.47" Diameter

from

$19.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Dayco – Flex Radiator Hoses; EPDM Rubber, 10.75 Inch Long, 1.5 Inch Inner Dia. (Part No.81131)

Flex Radiator Hoses; EPDM Rubber, 10.75 Inch Long, 1.5 Inch Inner Dia.

from

$18.29
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:
  • Designed to meet OE specifications
  • Not suitable for oil or heat transfer
  • Meets SAE J20R4, Class D-2 requirements for improved service hoses
  • This hose is designed to prevent splitting, ballooning, and elongation
See More

Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter (Part No.900423A)

O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter

from

$102.99
This pulley assembly is Supplied by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley assembly is produced for serpentine belt routing and tensioning applications. This pulley assembly conforms to original equipment material and tolerances, specifications and meets performance and durability requirements. Made for Subaru applications as a belt tensioning device. Kit is comprised of bracket, pulley, attachment bolt, tensioning bolt, washer and nuts. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More

Dayco – Serpentine Idler/Tensioner Pulley; Steel, 70mm Dia., 20.4mm Width, 4 Grooves (Part No.89029)

Serpentine Idler/Tensioner Pulley; Steel, 70mm Dia., 20.4mm Width, 4 Grooves

from

$57.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl

Product Features:
  • Designed for the majority of automotive vehicle applications on the road today
  • High-quality materials help resist wear and improve belt life
  • Features premium lubricated bearings to extend service life
  • Meets or exceeds OE quality
See More

Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter (Part No.900043A)

O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter

from

$55.99
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._

Product Features:
  • Manufactured by one of the largest original equipment part suppliers in the world to ensure proper form, fit, and performance
  • Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance
  • Installation instructions included.
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W1000139494BAN)

Multi Rib (Serpentine) Belt

from

$25.79
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

ACDelco – Professional V-Ribbed Serpentine Belt (Part No.W1000578651ACD)

Professional V-Ribbed Serpentine Belt

from

$52.24
ACDelco Professional, premium aftermarket V-Ribbed Advanced Technology Belts serve as replacement belts for accessory belt drive systems (ABDS) and other serpentine belt applications. They are designed using advanced manufacturing technology and premium EPDM rubber construction to provide customers with superior accessory belt drive systems (ABDS) and new-vehicle-type performance. These premium aftermarket replacement v-ribbed advanced technology belts are manufactured to meet or exceed your expectations for fit, form, and function.

Product Features:
  • Made with temperature and crack resistant EPDM rubber for a long life and quiet, dependable performance
  • Is the belt of choice by professional technicians, lasting 50% to 60% longer than retail belts (low priced belts sold at car part stores)
  • Its precision dimension control of rib profile transmits load efficiently throughout the accessory belt drive systems (ABDS) allowing components to operate at optimum levels
  • Able to operate and accept misalignment in the accessory belt drive systems (ABDS) far greater than other serpentine belts
  • Its flexible construction allows the belt to withstand billions of topside and backside bends resulting in a long belt life
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W100027670BAN)

Multi Rib (Serpentine) Belt

from

$15.10
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

Dorman – Idler Pulley Adjuster Bolt Kit (Part No.917-124)

Idler Pulley Adjuster Bolt Kit

from

$33.49
This idler pulley adjustment bolt kit is designed to match the original hardware required to repair the idler pulley on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:
  • Direct replacement – this accessory drive belt idler pulley adjustment bolt kit is designed to match the original hardware required to repair the idler pulley on specified vehicles
  • Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to wear
  • Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Gates – Premium Molded Coolant Hose (Part No.22885)

Premium Molded Coolant Hose

from

$32.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 8.25" Long, 1.44" Diameter (Part No.B71526)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 8.25" Long, 1.44" Diameter

from

$18.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Driveworks – Poly Rib Belt Serpentine Belt; 77.1 Long, 6 Rib Count (Part No.770K6)

Poly Rib Belt Serpentine Belt; 77.1 Long, 6 Rib Count

from

$20.49
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
See More

Dayco – Ela Poly Rib Belt (Part No.E040318)

Ela Poly Rib Belt

from

$23.99
Dayco ela (elastic) or stretch belts are specifically designed for two, three, and four point drives that are designed to use self-tensioning belts. Although these belts may look like standard poly rib belts, they are very different. These specially designed elastic belts have self-tensioning capabilities required by specific OE drives. Vehicles that are manufactured with stretch belts must replace them with stretch belts. These belts are not interchangeable with standard constructed belts of their same size. Dayco ela belts utilize a proprietary EPDM construction that is designed to elongate over the fixed pulley system, and then maintain the required belt tension over the life of the belt. The backbone behind the Dayco ela belt is its specially developed polyamide tensile member, which allows for high elongation required for installation, yet provides the proper tension maintenance properties to transmit the accessory loads demanded for the drive. This belt construction incorporates a wear resistant EPDM rib material, along with a highly elastic EPDM cushion rubber that surrounds the polyamide tensile cord, thus providing the required adhesion and flexibility to maintain lasting performance. Stretch belts have unique installation instructions depending on the OE application. Installation may require a specialized tool for the application or a simple zip tie. Do not attempt to install by prying the belt on the pulleys. Dayco provides detailed instructions on the reverse side of the sleeve.

Product Features:
  • Utilizes a proprietary EPDM construction that is designed to elongate over the fixed pulley system, and then maintain the required belt tension over the life of the belt
  • Specially developed polyamide tensile member, which allows for high elongation required for installation, yet provides the proper tension maintenance properties to transmit the accessory loads demanded for the drive
  • Incorporates a wear resistant EPDM rib material, along with a highly elastic EPDM cushion rubber that surrounds the polyamide tensile cord, thus providing the required adhesion and flexibility to maintain lasting performance
  • These specially designed elastic belts have self-tensioning capabilities required by specific OE drives designed for a stretch belt
See More

Dayco – Poly Rib Belt Serpentine Belt; 85.04 Long, 6 Rib Count (Part No.5060850)

Poly Rib Belt Serpentine Belt; 85.04 Long, 6 Rib Count

from

$59.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Gates – Micro-V« Serpentine Drive Belt (Part No.K050345)

Micro-V« Serpentine Drive Belt

from

$26.99
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.

Product Features:
  • Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
  • EPDM rubber constructions resist cracking on the rib surface
  • Meets or exceeds all specifications from the Original Equipment Manufacturer
  • Tensioner Replacement is Recommended (if equipped)
  • Unique form grinding of each individual belt assures precise dimensional control.
  • Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
See More

Dayco – Poly Rib Belt Serpentine Belt; 35.25 Long, 4 Rib Count (Part No.5040353)

Poly Rib Belt Serpentine Belt; 35.25 Long, 4 Rib Count

from

$24.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)

Metal Line Kit for Engine Oil Coolers

from

$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:
  • Metal line kit
  • For use in engine oil cooler applications
  • Routes oil lines past exhaust manifolds
  • Provides protection where standard hoses can fail
See More

Dorman – Coolant Pipe For Oil Cooler (Part No.626-594)

Coolant Pipe For Oil Cooler

from

$38.99
This engine oil cooler hose assembly matches the fit and function of the original equipment components for reliable repair and restoration of proper oil circulation between the oil cooler and engine.

Product Features:
  • Ideal replacement – this engine oil cooler hose assembly is a direct replacement for the original hose assembly
  • Quality materials – this engine oil cooler hose assembly is made from corrosion-resistant materials to ensure the smooth transfer of oil from the engine to the cooler
  • Easy to install – no special tools required
  • Quality tested – rigorous quality control ensure this hose assembly conforms to product standards
See More

Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)

1/2" x 12' Engine Oil Cooler Hose

from

$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:
  • Engine oil cooler hose
  • Size: 1/2″ x 12′
  • Designed for engine oil applications
  • 12′ hose length accommodates most applications
See More

2005 Subaru Impreza Belts and Hoses

You count on your 2005 Subaru Impreza to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 25 Belts and Hoses ranging in price from $8.29 to $79.99, you’re sure to find everything you need for your 2005 Subaru Impreza.

Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 7 different brands like Dayco, Driveworks, and Dorman. 2005 Subaru Impreza Belts and Hoses start as low as $8.29!

One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 472 extensive product reviews on 2005 Subaru Impreza Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 21 1/4 Inch Length with 4.9 stars and Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13" Long, 1.50" Diameter with 4.7 stars.

Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2005 Subaru Impreza below to get started!

Top-Rated Belts and Hoses Brands For Your 2005 Subaru Impreza

Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2005 Subaru Impreza running right for years to come. In our inventory you’ll find brands like Dayco, Driveworks, Dorman, and even more.

Popular Dorman Belts and Hoses

You’ll find popular Dorman brand products across Pulleys. All are waiting to get your 2005 Subaru Impreza back on the road. Some of the top-rated Dorman products in these categories are:
Idler Pulley Adjuster Bolt Kit
from $33.49
(5)
Idler Pulley Adjuster Bolt Kit
Idler Pulley Bolts

Top-Rated Dayco Belts and Hoses


If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2005 Subaru Impreza, and some of our most reviewed Dayco parts include:
Poly Rib Belt Serpentine Belt; 35.25 Long, 4 Rib Count
from $24.99
(20)
Poly Rib Belt Serpentine Belt; 35.25 Long, 4 Rib Count
Serpentine Belts
Poly Rib Belt Serpentine Belt; 35.04 Long, 5 Rib Count
from $24.99
(18)
Poly Rib Belt Serpentine Belt; 35.04 Long, 5 Rib Count
Serpentine Belts

FAQs for 2005 Subaru Impreza Belts and Hoses

What are the most purchased Belts and Hoses for the 2005 Subaru Impreza?

Out of 25 Belts and Hoses for the 2005 Subaru Impreza, the most popular in our inventory are:
Poly Rib Belt Serpentine Belt; 35.25 Long, 4 Rib Count
from $10.99
(25)
Poly Rib Belt Serpentine Belt; 35.25 Long, 4 Rib Count
Serpentine Belts

What are the top-rated 2005 Subaru Impreza Belts and Hoses?

Top-rated Belts and Hoses for your 2005 Subaru Impreza based on customer reviews/ratings are:
Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 21 1/4 Inch Length
from $33.49
(8)
Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 21 1/4 Inch Length
“High quality, replacement”