2005 Nissan Titan Tools

Yoke holder tool, fits most yokes. 1310/1330/1350/1410/7260/7290/MR3/Toyota. No return.

Product Features:

• Yoke holder tool
• Firmly holds pinion yoke in place allowing for easier pinion preload setting

Hypertech’s In-line Speedometer Calibrator Module is an in-line module to correct the speedometer and odometer for non-stock tire sizes and/or rear gear ratios. This module is perfect for vehicles with computers that don’t allow for tire size and/or rear gear ratio correction or re-calibrate for tire sizes and/or rear gear ratios outside the range of programmers. If you’ve installed tires that are larger or smaller than original equipment tires, or if you have installed a ring and pinion gear set with a different rear gear ratio, the Speedometer Calibrator allows you to correct speedometer and odometer readings. The vehicle’s computer calculates your vehicle’s speed based on the diameter of the stock tires. If you’ve installed taller or shorter tires, or changed the rear gear ratio, the vehicle’s computer doesn’t know how fast your vehicle is going. As a result, the speedometer readings will not be accurate (as required by law). Using the USB cable connect, the In-line Speedometer Calibrator Module to your PC and enter the new tire height and/or rear gear ratio. There are no limitations for increasing tire height or rear gear ratios. Next, disconnect the factory connector to the instrument cluster (behind the dash), snap in the Speedometer Calibrator Module, reconnect the cluster, and you’re done! In a matter of minutes, you can accurately correct your speedometer and odometer readings (as required by law).

Product Features:

• Perfect for vehicles with computers that don’t allow for tire size and/or rear gear ratio correction or re-calibrate for tire sizes and/or rear gear ratios outside the range of programmers.
• Inline speedometer correction device installs easily to the factory wiring harness
• Use to recalibrate after tire/gear change
• Return back to factory settings
• Reads/Displays/Clears Diagnostic Trouble Codes (DTC’s)
• Internet updateable

Hypertech’s In-line Speedometer Calibrator Module is an in-line module to correct the speedometer and odometer for non-stock tire sizes and/or rear gear ratios. This module is perfect for vehicles with computers that don’t allow for tire size and/or rear gear ratio correction or re-calibrate for tire sizes and/or rear gear ratios outside the range of programmers. If you’ve installed tires that are larger or smaller than original equipment tires, or if you have installed a ring and pinion gear set with a different rear gear ratio, the Speedometer Calibrator allows you to correct speedometer and odometer readings. The vehicle’s computer calculates your vehicle’s speed based on the diameter of the stock tires. If you’ve installed taller or shorter tires, or changed the rear gear ratio, the vehicle’s computer doesn’t know how fast your vehicle is going. As a result, the speedometer readings will not be accurate (as required by law). Using the USB cable connect, the In-line Speedometer Calibrator Module to your PC and enter the new tire height and/or rear gear ratio. There are no limitations for increasing tire height or rear gear ratios. Next, disconnect the factory connector to the instrument cluster (behind the dash), snap in the Speedometer Calibrator Module, reconnect the cluster, and you’re done! In a matter of minutes, you can accurately correct your speedometer and odometer readings (as required by law).

Product Features:

• Perfect for vehicles with computers that don’t allow for tire size and/or rear gear ratio correction or re-calibrate for tire sizes and/or rear gear ratios outside the range of programmers.
• Inline speedometer correction device installs easily to the factory wiring harness
• Use to recalibrate after tire/gear change
• Return back to factory settings
• Reads/Displays/Clears Diagnostic Trouble Codes (DTC’s)
• Internet updateable

Tester adapter for the MT-300 cooling system pressure testers. Professional grade test equipment to ensure an automotive cooling system is operating at the correct pressure. Made from high quality materials to ensure durability. Designed to test automotive coolant caps.

Product Features:

• Machined metal construction
• Works with MT-300 pressure tester
• Tests coolant caps
• Professional quality

The REACT offers fully customizable control over your vehicle’s throttle response. The simple control knob allows you to switch between multiple modes and control the throttle intensity of each mode on-the-fly. The REACT installs easily and is completely plug-and-play, has an automatic setup sequence so no disassembly is required, comes with a magnetic A/C vent mount (Pedestal swivel mount also available – Sold separately at hypertech.com/REACT.aspx), and doesn’t void your factory warranty. Plus the REACT is internet updateable. Three (3) versions of the REACT throttle optimizer are available to fit your particular driving needs… Performance, Off-Road, and Tow.

Product Features:

• On-The-Fly Adjustments
• LED Setting Indicators
• Multiple Levels Of Safety Protection
• Magnetic A/C Vent Mount Incl. [No Screw Or Tape]
• Pedestal Swivel Mount Available [Sold Separately]
• Custom Tuning Software
• Internet Updateable
• Easy Plug-N-Play Install
• Automatic Setup Sequence [No Disassembly Required]
• Doesnt Void Factory Warranty
• Product might not be available in all states due to local laws.

The REACT offers fully customizable control over your vehicle’s throttle response. The simple control knob allows you to switch between multiple modes and control the throttle intensity of each mode on-the-fly. The REACT installs easily and is completely plug-and-play, has an automatic setup sequence so no disassembly is required, comes with a magnetic A/C vent mount (Pedestal swivel mount also available – Sold separately at hypertech.com/REACT.aspx), and doesn’t void your factory warranty. Plus the REACT is internet updateable. Three (3) versions of the REACT throttle optimizer are available to fit your particular driving needs… Performance, Off-Road, and Tow.

Product Features:

• On-The-Fly Adjustments
• LED Setting Indicators
• Multiple Levels Of Safety Protection
• Magnetic A/C Vent Mount Incl. [No Screw Or Tape]
• Pedestal Swivel Mount Available [Sold Separately]
• Custom Tuning Software
• Internet Updateable
• Easy Plug-N-Play Install
• Automatic Setup Sequence [No Disassembly Required]
• Doesnt Void Factory Warranty
• Product might not be available in all states due to local laws.

This Bully Dog GT Platinum tuner is four products in one: a vehicle engine tuner, monitor, gauge, and diagnostic device.ÿ

Product Features:

• Dramatically improves the utility of your vehicle by increasing horsepower, improving fuel economy, and providing a comprehensive set of monitoring features and diagnostic functions.
• Bully Dog GT Platinum tuners are incomparable to other tuning products because they have the largest feature set and the widest range of vehicle applications available.
• Product might not be available in all states due to local laws.

Brakes are designed as a system and all the parts need to work together for best performance. The Bleeder Screw clears the air out of the brake line, normally placed at the highest point of the caliper or cylinder.

Product Features:

• Manufactured with quality materials to suppress high stress levels
• Direct replacement for a proper fit
• Corrosion resistant coating for long-lasting durability against harsh roads
• Provides smoother braking
• This part matches Original Equipment (OE) quality specifications

Brakes are designed as a system and all the parts need to work together for best performance. The Bleeder Screw clears the air out of the brake line, normally placed at the highest point of the caliper or cylinder.

Product Features:

• Manufactured with quality materials to suppress high stress levels
• Direct replacement for a proper fit
• Corrosion resistant coating for long-lasting durability against harsh roads
• Provides smoother braking
• This part matches Original Equipment (OE) quality specifications

Russell’s wide variety of lightweight aluminum adapter fittings allow for the connection of Russell hose ends to almost any component. Adapters are offered in standard thread, metric thread and pipe thread to fit most popular oil pumps, fuel pumps, fuel f

Brakes are designed as a system and all the parts need to work together for best performance. The Bleeder Screw clears the air out of the brake line, normally placed at the highest point of the caliper or cylinder.

Product Features:

• Manufactured with quality materials to suppress high stress levels
• Direct replacement for a proper fit
• Corrosion resistant coating for long-lasting durability against harsh roads
• Provides smoother braking
• This part matches Original Equipment (OE) quality specifications