2005 GMC Envoy Ignition Boots

NGK ultra-low resistance mag core wire sets provide outstanding performance and durability. High-temp premium silicone outer jacket and inner EPDM/silicone insulation contain high voltage currents for excellent dielectric strength. Stainless steel winding

Product Features:

• PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
• BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
• STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
• CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

NGK Coil on Plug Boots are built to stringent OEM tolerances, combining original equipment fit, design and outstanding durability. NGK Coil on Plug Boots are manufactured using only premium silicone and always include any required internal springs and ferrite resistors for superior performance and RFI noise suppression. Bridging the important link between ignition coil and spark plug, COP boots should always be replaced with NGK Coil on Plug Boots at the time as changing spark plugs to prevent ignition problems such as flashover.

Product Features:

• PREMIUM GRADE SILICONE: Designed to withstand harsh environments
• OEM MATCHED: Includes all required internal springs and ferrite resistors for superior performance and RFI noise suppression

NGK ultra-low resistance mag core wire sets provide outstanding performance and durability. High-temp premium silicone outer jacket and inner EPDM/silicone insulation contain high voltage currents for excellent dielectric strength. Stainless steel winding

Product Features:

• PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
• BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
• STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
• CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

Prenco Coil on Plug Boots provide the best protection possible for your ignition system versus the harsh environment created by the modem day engine. Prenco Coil on Plug Boots are constructed using the finest quality materials and compounds, and produced with superior quality tooling that exactly matches the Original Equipment Boot.

Product Features:

• Prenco Coil on Plug Boots are produced using precise computer designed tooling and premium quality materials/compounds that are formulated to perform in extreme temperatures.
• Prenco Coil on Plug Boots are designed as a direct replacement for the OE Boot. Springs, grommets and ferrite resistors are provided for all applications where applicable.
• Inspect and replace Coil on Plug Boots every 50,000 miles and/or with every spark plug change to ensure optimum engine efficiency and performance.
• Replacing Coil and Plug Boots at regular intervals will prevent/correct misfires and will help to minimize further costly damage to Ignition Coils, Sensors, Catalytic Convertors, and ECUs.

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications