2005 Chevrolet Trailblazer Ext Ignition Wires

ACDelco GM Original Equipment Spark Plug Wire Sets consist of a set of wires, encased in an insulating material, connectors, and insulating boots, and are GM-recommended replacements for your vehicle’s original components. The wires transfer high voltage pulses between the voltage source, the distributor, and the spark plug. These original equipment wires have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Durable to help transfer high voltage pulses without damage
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

NGK ultra-low resistance mag core wire sets provide outstanding performance and durability. High-temp premium silicone outer jacket and inner EPDM/silicone insulation contain high voltage currents for excellent dielectric strength. Stainless steel winding

Product Features:

• PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
• BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
• STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
• CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications
• Conductor core features DuPont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

Built to match the Original Equipment in length and fit, ACDelco Professional Ignition Wire Sets also offer a performance advantage over many aftermarket products.

Product Features:

• Designed to match Original Equipment wire sets in critical areas such as cable length and diameter, terminal design and insulator position.
• Have broad coverage available for most vehicles on the road today from 1980 to present.
• Provide a high degree of Radio Frequency Interference (RFI) suppression.
• Are designed to offer fit, form and function for optimum performance.
• Kevlar®-reinforced fiberglass core in select sets for increased strength.
• Core sheathed in radio-static-absorbent material for increased RFI suppression.
• Wire-wound, stainless-steel alloy conductor for maximum spark delivery and RFI suppression on most applications.
• A layer of conductive heat-resistant latex for added durability.
• Insulating rubber-based compound inner jacket helps minimize voltage drop and enhance durability.
• Thick silicone outer jacket for excellent heat resistance.

Prenco Coil on Plug Boots provide the best protection possible for your ignition system versus the harsh environment created by the modem day engine. Prenco Coil on Plug Boots are constructed using the finest quality materials and compounds, and produced with superior quality tooling that exactly matches the Original Equipment Boot.

Product Features:

• Prenco Coil on Plug Boots are produced using precise computer designed tooling and premium quality materials/compounds that are formulated to perform in extreme temperatures.
• Prenco Coil on Plug Boots are designed as a direct replacement for the OE Boot. Springs, grommets and ferrite resistors are provided for all applications where applicable.
• Inspect and replace Coil on Plug Boots every 50,000 miles and/or with every spark plug change to ensure optimum engine efficiency and performance.
• Replacing Coil and Plug Boots at regular intervals will prevent/correct misfires and will help to minimize further costly damage to Ignition Coils, Sensors, Catalytic Convertors, and ECUs.

NGK Coil on Plug Boots are built to stringent OEM tolerances, combining original equipment fit, design and outstanding durability. NGK Coil on Plug Boots are manufactured using only premium silicone and always include any required internal springs and ferrite resistors for superior performance and RFI noise suppression. Bridging the important link between ignition coil and spark plug, COP boots should always be replaced with NGK Coil on Plug Boots at the time as changing spark plugs to prevent ignition problems such as flashover.

Product Features:

• PREMIUM GRADE SILICONE: Designed to withstand harsh environments
• OEM MATCHED: Includes all required internal springs and ferrite resistors for superior performance and RFI noise suppression

Product Features:

• SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
• Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
• 100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
• EPDM inner insulation stops power-robbing voltage leaks.
• With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
• Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
• Excellent interference suppression and consistent performance
• Easy lock terminals for more convenient installation.
• Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
• Broad coverage available for most vehicles on the road today
• Include grease pack to ensure easy installation and removal

CARQUEST Premium coil on plug boots are engineered to restore ignition boot reliability and performance. We have OE design providing an exact direct fit for your application and the performance and durability meet or exceed OE requirements. It offers excellent heat resistance as well as maximum protection against spark loss. With durable silicone compound for resistance to high heat or abrasion.

Product Features:

• Provides excellent heat resistance as well as maximum protection against spark loss.
• Durable silicone compound for resistance to high heat or abrasion
• Spring included with the coil boot
• Design for direct compatibility
• OE design provides an exact fit for your application
• Multipack provides one time replace all COP for better deal