2005 Chevrolet SSR Fuel and Emissions Systems

The ACDelco GM Original Equipment Fuel Cap is a threaded cap that seals your vehicle’s fuel tank filler, and is a GM-recommended replacement for your vehicle’s original component. The fuel cap has a rubber gasket that provides a liquid-tight seal to keep fuel in and water and dirt out. The cap may have a check-valve that lets air in or out depending on the air pressure inside the tank. This original equipment regular fuel cap has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Provides a tight seal to keep your vehicle’s fuel tank closed
• A sealed fuel tank reduces vapor emissions which helps the environment
• Prevents lost fuel in order to help reduce your trips to the gas station
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

To perform a complete fuel pump replacement, clean the tank every time. Order the Delphi Fuel Tank Cleaning Kit (Part FC01). Remember, the original pump went into a clean fuel tank, to ensure the same level of performance, the new pump should too. 100 ye

Product Features:

• Helps avoid premature fuel pump failure
• Lint free towel included
• Low suds formulation
• Removes harmful contaminants from the fuel tank

GM Genuine Parts Fuel Injector and Insulator Retainer Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies

This fuel level sensor is designed to match the fit and function of the original sensor on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this fuel level sensor is designed to match the fit and function of the original sensor on specified vehicles
• Ideal solution – this sensor is a reliable replacement for an original part that has failed due to fatigue or electrical malfunction
• Durable construction – this sensor is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

The ACDelco GM Original Equipment Fuel Pump Tank Seal is a GM-recommended replacement component that provides the same performance, durability, and service life as your factory original equipment.

Product Features:

• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

100 years of OE experience, supplier to the world’s top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.

Product Features:

• Delphi is a global OE manufacturer and all fuel pumps are built to Delphi’s OE standards
• Empty float height and float retention matches OE specifications and guarantees correct gas gauge reading
• Lower amperage draws less load on vehicle’s electrical system
• Part is validated, tested and matched to the right vehicle application
• Always be sure to check and clean fuel tank to avoid unnecessary returns
• Lower failure rates due to its innovative design and durability

An ACDelco GM Original Equipment Fuel Injection Pressure Regulator is a GM-recommended replacement for your vehicle’s original component. The Fuel Injection Pressure Regulator is a mechanical valve that controls the fuel pressure in the fuel injector rail. The spring-loaded valve returns excess fuel back to the fuel tank. This original equipment fuel injection pressure regulator has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Fully tested against leaks
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Fuel Line Clip

This fuel line clip is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

• Direct replacement – this fuel line clip matches the fit and function of the factory part on specified years, makes and models
• Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Bosch is the world’s leading supplier and original equipment manufacturer of Oxygen Sensors. Bosch invented the automotive oxygen sensor and leads the way in sensor technology and innovation advancements. From overall sensor design to the critical ceramic element, Bosch is known worldwide for quality and performance.  Bosch oxygen sensors deliver exceptional OE level reliability, performance and durability, further improving service life of the product. 

Product Features:

• Premium Bosch oxygen sensors are designed to improve fuel economy while reducing harmful emissions
• Direct Fit includes OE Connector for easy installation
• Performance meets or exceeds OE specifications
• True Direct-fit OE connectors and harness

Product Features:

• Our units are all pre-aligned & pre-adjusted to save installation time and ensure proper switching.
• A lubricated felt pad that lubricates the cam lobes on the vehicles distributor. This reduces wear on the point set rubbing block, extending the usable life of the part.
• Ventilated where available, tungsten contacts, which run cooler and exhibit less erosion.
• The copper-alloy shunt provides superior resistance to breakage, due to the flexing of the moving arm on the point set. It also significantly increases current conductivity over typical steel, shunts.

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

All Edelbrock fuel rails are machined from high quality extruded aluminum. Each kit includes fuel rails, stands and mounting hardware. Fuel fittings, crossover line and regulator not included. 3629 Fuel Rail Kit is for LS1 engines with Pro-Flo XT Manifold

Product Features:

• Black AnodizedFinish
• High Capacity Fuel Rails
• For Use W/ Pro-Flo XT Manifold #7139
• -6 AN Inlet / Outlet
• Made In The USA

ACDelco is a global leader in automotive replacement parts and related services and offers quality aftermarket products for most makes and models, including General Motors, Ford, Chrysler, Toyota and Honda. ACDelco has over 100 years of experience in the automotive industry and is a brand of GM Customer Care and After sales, a division of General Motors.

Building upon a foundation of premium full-line products established under NGK ignition and NTK oxygen sensor products, NTK’s expansion to technical sensors is part of our ongoing commitment to streamline product types and increase coverage under one premium brand: NTK, The Sensor Specialist. With over 80 years of automotive expertise, NGK’s family of automotive products are driven by extreme dedication to innovation, performance and quality. NTK is the only OE supplier with a full-line of technical sensors in the aftermarket for import and domestic vehicles. Drawing from OE experience, NTK sensors undergo extreme testing conditions that include thermal shock, vibration and OBD verification. NTK sensors are manufactured to ensure a quality that meets or exceeds OE specifications. As new vehicles incorporate connected and automated technologies, trust The Sensor Specialist for full-line market support and OE application technology.

Product Features:

• NTK’s Manifold Absolute Pressure Sensors are manufactured to operational performance standards to meet or exceed OE fit, form and function to ensure proper manifold pressure, fuel metering and ignition timing.
• The Manifold Absolute Pressure Sensor (MAP) provides manifold pressure information to the Engine Control Unit (ECU). The data is used to determine the air mass flow rate and required fuel for optimum combustion and ignition timing.

ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Protective outer coverings help provide long-lasting durability
• Color-coded wires allow for easy installation
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

Pressure sensors are used within several operating systems on the vehicle. Subjects in this category measure the pressure of both liquid and air to include air in a positive pressure and negative pressure range. Pressure sensors report out as the result of an electrical device called a strain gauge which produces an analog or digital signal output dependent on the needs of the circuit. Pressures may be very low such as barometric pressure, or extremely high such as in a high-pressure fuel injection system.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
• Robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
• Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

GM Genuine Parts Fuel Pressure Relief Valve Caps are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies

Recommended for replacement whenever the fuel tank is replaced or serviced, this strap is a direct replacement for the original. Manufactured from durable materials to withstand harsh road and weather conditions.

Product Features:

• Direct replacement – this fuel tank strap matches the fit, function and performance of the original part
• Ideal solution – recommended for replacement when the fuel tank is serviced or replaced
• Durable construction – manufactured from quality materials for superior service and reliability
• Trustworthy design – backed by 100 years of automotive aftermarket experience

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

The ACDelco GM Original Equipment Fuel Tank Sending Unit is a GM-recommended replacement for your vehicle’s original component. The Fuel Tank Sending Unit consists of a float connected to a thin, metal rod that is mounted to a resistor. Together, these components sense fluid level changes, which are reflected on the vehicle’s fuel gauge. This original equipment sending unit has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Designed with thick wiper contacts and wear pads that provide durability, especially with today’s ethanol fuels
• Design helps eliminate complications due to worn fingers on the sensor wiper arm, sulfur contamination, and failures of wire wound sensors and/or lead sensor kits
• GM-recommended replacement part for your GM vehicle’s original factory fuel tank sending unit
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

The Delphi Fuel Level Sensor is a magnetic, non-contacting angular position sensor that converts rotary motion into an electrical signal to provide accurate fuel level measurement and enable reliable fuel gauge readout. Its small, modular design allows a wide range of applications and its calibrated output signal compensates for component and assembly variations. Design features enable dependable performance and durability. The Fuel Level Sensor’s linear output voltage is directly proportional to the sensor’s field, perpendicular to the sense element. Non-contact performance is made possible by state-of-the-art linear programmable, fully integrated Hall effect and Anisotropic magneto resistive (AMR) technologies. Rotating magnets generate Hall voltage with a sine wave response signal, with zero when the magnets are parallel to the sense element and plus/minus when the magnets are at angles to the sense element. The sensor operates in a linear region of the sine wave response signal. The Delphi Fuel Level Sensor features a proven magnetic circuit technology that has been used in high volume absolute position sensor applications for more than 10 years. The non-contacting design of the sensor maximizes product life by eliminating signal deterioration due to contact wear, ink failure or dendritic growth. Its low current draw with high resolution output signal may be calibrated for the angular travel of a specific application to compensate for assembly variations.

Product Features:

• Low cost with electrical interface that powers and reads Hall effect output signal
• High volume manufacturing processes help achieve competitive cost
• Can be easily modified to meet specific customer requirements
• Protection against contamination and fuel exposure
• Lower drive current minimizes system power consumption
• High resolution linear output signal with low hysteresis for improved system performance
• Electro-Magnetic Capability (ECM) compliance
• Available with 2-wire Pulse Width Modulation (PWM) interface, and may be designed for 3-wire PWM or ratiometric interfaces for application flexibility

These bolts are manufactured using durable materials and corrosion-tested to ensure required strength and longevity.

Product Features:

• Durable materials – manufactured to specific thread tolerance standards
• Corrosion tested – hardware undergoes salt spray testing to ensure corrosion resistance
• Multipurpose usefulness – can be used in a variety of applications, from auto to home
• Trustworthy quality – backed by team of professional engineers and quality control specialists in the United States

CARQUEST MAP sensors are manufactured with critical OEM components to ensure that your engine runs efficiently to reach the best gas mileage on your vehicle.

Product Features:

• CARQUEST MAP sensors connectors are exact OE fit to ensure the proper vacuum is maintained to prevent power loss and to minimize internal contamination.
• CARQUEST MAP sensors utilize high temperature resistant seals. Damaged seals can directly impact the vehicles fuel-to-air ratio, making it less fuel efficient.
• CARQUEST MAP sensors are 100% individually tested for all product functionalities including proper vacuum seal and electrical output.

ACDelco GM Original Equipment Manifold Absolute Pressure (MAP) Sensors measure intake manifold pressure, and are GM-recommended replacements for your vehicle’s original components. The MAP sensor is a part of the fuel and engine management system. Its signal is used by the engine control module along with the throttle position sensor to calculate the amount of air entering the engine so that the correct amount of fuel is injected for optimum combustion. These original equipment manifold absolute pressure sensors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Sends signals to the engine controls for optimal engine performance
• Designed to adjust engine performance to various altitudes
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function