2003 Chevrolet Silverado 1500 Vehicle Hoods

Hood release cable broken- This hood release cable is durably built to directly replace a worn-out or broken cable on specific vehicle years, makes and models.

Hood release cable broken? This hood release cable is durably built to directly replace a worn-out or broken cable on specific vehicle years, makes and models.

Hood release cable broken? This hood release cable is durably built to directly replace a worn-out or broken cable on specific vehicle years, makes and models.

This hood release cable is durably built to directly replace a worn-out or broken cable on specific vehicle years, makes and models.

Dee Zee Tailgate Assist Safely controls the drop of your truck tailgate. Custom designed for each make and model. High quality and extensively tested to handle heave use for the life of the truck. Works in conjunction with factory cables. Easy, no drill installation that installs in minutes.

“Atlas Lift Supports are engineered to meet or exceed OE specifications to ensure your replacement will perform the same or better than your original lift supports. Atlas Lift supports are designed to prevent premature failures, with premium features such as a corrosion resistant exterior, OE grade end connectors, and Dynamic Dampening Technology. Dynamic Dampening Technology (DDT) is a precision groove engineered into the tube of the lift support, which allows the hatch to open at the optimum speed to prevent “”bouncing”” or “”Jumping”” at the end of the stroke. Lift Supports’ performance and longevity are affected by consistent usage, temperature changes, contact with weather elements, pulling or hanging on the part, and can cause unsafe conditions if not changed when signs of failure are present. Atlas Lift Supports are easy to replace and can be changed in minutes No Special Tools Required. Atlas Lift Supports also provide easy to read install for a quick and easy installation. Make sure to Always Replace in Pairs!”

Dee Zee Tailgate Assist Safely controls the drop of your truck tailgate. Custom designed for each make and model. High quality and extensively tested to handle heave use for the life of the truck. Works in conjunction with factory cables. Easy, no drill installation that installs in minutes.

New Standard Replacement Driver Side Hood Spring Hinge, Except 2011-2012 2500/3500 Heavy Duty Models

New Economy Replacement Hood Panel EXTERNAL SUPPLY>FDO>BACK ROOM-FDO>APPLICATION SPECIFIC from KAI

New Economy Replacement Hood Panel EXTERNAL SUPPLY>FDO>BACK ROOM-FDO>APPLICATION SPECIFIC from KAI

New CAPA Certified Standard Replacement Hood Panel

New Standard Replacement Passenger Side Hood Hinge Assembly, Body Mounted

New Standard Replacement Driver Side Hood Hinge, All 1500 Series Trucks

New Standard Replacement Driver Side Hood Hinge Assembly, Body Mounted

New Standard Replacement Passenger Side Hood Hinge

New Standard Replacement Driver Side Hood Hinge

Competition Cams , 13702-KIT. PERFORMANCE PARTS>PERFORMANCE ENGINE>ENGINE>ACCESSORIES & OTHER from Competition Cams

Our American Thunder cat-back exhaust system for 2007-2013 GM Silverado/Sierra 1500 with the 5.3L engine, is perfect for the person looking for moderately aggressive sound levels both inside and outside of the truck. This bolt-on emissions-legal system features 3.00-inch mandrel-bent stainless steel tubing flowing into a Super 40 Series muffler, for a deep powerful sound. The mandrel-bent 2.50-inch stainless steel tailpipes can be configured with your choice of exit locations, either straight out the back under the bumper for a muscular look, or exiting out behind the rear tires on each side of the truck. This is the ideal tailpipe location when towing a boat or RV. The tailpipes are finished off with large 3.50-inch double wall polished stainless steel tips. The system includes all necessary parts and hardware for an easy installation and is covered by our Limited Warranty. Notes: Fits all 2/4 wheel drives with 143.5 and 157.5-inch wheelbases. Also fits 2007-2008 GM Silverado/Sierra 1500 with 4.8L engines and 143.5 and 157.5-inch wheelbases.

This ring secures the upgraded trunnion/bearing assembly inside a factory GM LS rocker arm.

“Our new Flowmaster Flow FX cat-back exhaust system for the 2009-2013 GM Silverado/Sierra with 4.8L and 5.3L engines is manufactured using 409S stainless steel for years of trouble free service. System features include a 3.00-inch inlet pipe leading into a Flow FX “”straight-through”” performance muffler for great sound and maximum performance. The single 3.00-inch mandrel-bent tailpipe exits out the side behind the passenger side rear tire and is finished off with large 4.50 inch diameter black ceramic coated 304S stainless steel tip, giving your Silverado or Sierra that custom look that goes hand in hand with the deep performance sound of the Flow FX muffler. The system uses all the factory hanger locations and connections without any cutting or welding for an easy installation that you can do at home. Includes installation instructions and all necessary hardware. Note: Fits both 2/4 Wheel Drive models with 143.5 and 157.5-inch Wheelbases.”

“Introducing our new Flow FX Cat-back exhaust system for the 2019-2026 GM Silverado/Sierra 1500 with the 5.3L engine. The performance exhaust system fits both 2 and 4-Wheel drive models with 148 or 157-inch wheelbases and is manufactured from 409S stainless steel for years of trouble-free service. Features include a 3.00-inch inlet pipe leading into a Flow FX “”straight-through”” muffler for great sound and maximum performance. Maximum dyno gains of 10 hp and 12 lb.ft of torque at the rear wheels. The 3.00-inch mandrel-bent tailpipe exits out behind the rear passenger side tire and is finished off with large 4.50-inch diameter black ceramic coated 304S stainless steel tip, giving your Silverado/Sierra that custom look that goes hand in hand with the deep performance sound of the Flow FX muffler. The system uses all the factory hanger locations and connections for an easy installation that you can do at home. Includes detailed instructions and all necessary hardware.”

“This Flowmaster Flow FX cat-back exhaust system for the 2011-2018 GM 1500 trucks with the 6.2-liter V8 engine is manufactured using durable 409 stainless steel throughout and features single 3.50-inch to dual 2.50-inch mandrel bent pipes for better exhaust gas flow, and a Flow FX “”straight-through”” muffler is used for a moderate sound level and maximum performance. Maximum increases on the dyno revealed +11 hp and +15 lb-ft at the rear wheels. This system exits out both sides, behind the rear wheels with 4.50-inch black ceramic tips for added style and a custom look. The system uses all the existing factory hanger locations and includes installation instructions and all necessary hardware for an easy installation that you can do at home. Backed by Flowmaster’s Limited Warranty.”

This cowl cover is designed to match the fit and appearance of the original cover on specified vehicles, and is engineered for durability and reliable performance.

This cowl cover is designed to match the fit and appearance of the original cover on specified vehicles, and is engineered for durability and reliable performance.

This cowl cover is designed to match the fit and appearance of the original cover on specified vehicles, and is engineered for durability and reliable performance.

This cowl cover is designed to match the fit and appearance of the original cover on specified vehicles, and is engineered for durability and reliable performance.

This cowl cover is designed to match the fit and appearance of the original cover on specified vehicles, and is engineered for durability and reliable performance.