2003 Buick Century Torque Converter and Related Products

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

This HoleShot 3600 fits 1965-91 GM TH400, 425, 375 and 1968-81 TH350, 375B (not 350C.) Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 3600 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Features both 10.75 and 11.50-inch bolt circle.

B&M Nitrous HoleShot 3000 stall for 1965-91 TH400, 425 and 1968-81 TH350, 375 transmissions (Not TH350C) is an excellent choice for vehicles with engine modifications, particularly big cams that tend to reduce low end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Nitrous Holeshot converters feature furnace brazed impeller and turbine, new precision steel alloy pump drive tube, new heavy duty needle bearings between the stator and impeller (not a thrust washer) and needle bearings between the stator and turbine. Other features include dual pattern 10.75 and 11.50-inch bolt circle, a new turbine hub, new springs and rollers in the stator and anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower that a nitrous plate system delivers. Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. These are serious converters for serious performance street cars. To prevent contamination left from worn parts being circulated in your new components causing premature wear, we strongly recommend protecting your investment by adding a B&M transmission cooler with all new transmission installations. Listed converters are NOT to be used in trans-brake applications. Not for use in trans-brake applications. Has both 10.75 and 11.50-inch bolt circles.

HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle.

Hays Twister Full Race Torque Converters feature a custom designed anti-balloon plate to stop any converter ballooning and swelling in racing situations. These torque converters are designed for use with a trans-brake and great for power adders such as nitrous, superchargers, and turbos. They are available with various RPM stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss.

This B&M Traveler torque converter fits GM 1968-81 TH350, TH375B (will not fit TH350C) automatic transmissions. Traveler torque converters are an excellent choice for stock vehicles, vehicles with light performance modifications, tow vehicles and RV’s. They will increase the stall speed by approximately 300 rpm over a factory stock converter. The additional stall of the Traveler makes acceleration much crisper and fun to drive. Features include fully balanced and pressure tested by expert technicians and are manufactured to B&M’s exacting tolerances for long life and includes new precision pump drive tube, heavy duty needle bearings, furnace brazed and new sprag and rollers in stator. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

This Holeshot 3200 fits 1965-91 GM TH400, 425, 375 and 1968-81 TH350, 375B (not 350C) transmissions. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2400 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings.

Hays Twister Full Race Torque Converters feature a custom designed anti-balloon plate to stop any converter ballooning and swelling in racing situations. These torque converters are designed for use with a trans-brake and great for power adders such as nitrous, superchargers, and turbos. They are available with various RPM stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss.

Hays Twister 3/4 Race Torque Converters–Good names never go away, and neither should good terms!

Hays Twister Full Race Torque Converters feature a custom designed anti-balloon plate to stop any converter ballooning and swelling in racing situations. These torque converters are designed for use with a trans-brake and great for power adders such as nitrous, superchargers, and turbos. They are available with various RPM stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss.

The HoleShot 2000 fits 1965-91 GM TH400, 425, 375 and 1968-81 TH350, 375B (not 350C) transmissions are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

Hays Twister 3/4 Race Torque Converters–Good names never go away, and neither should good terms!

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

Hays Twister Full Race Torque Converters feature a custom designed anti-balloon plate to stop any converter ballooning and swelling in racing situations. These torque converters are designed for use with a trans-brake and great for power adders such as nitrous, superchargers, and turbos. They are available with various RPM stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss.

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Hays Twister 3/4 Race Torque Converters–Good names never go away, and neither should good terms!

Hays Twister 3/4 Race performance torque converters are a perfect addition to our line of performance flexplates, clutches, and flywheels. Our 3/4 Race series of torque converters is intended for street/strip combinations, with various stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss. The Twister 3/4 Race torque converter perfectly describes a converter suited for an application just shy of Full Race converter.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

Hays Twister Full Race Torque Converters feature a custom designed anti-balloon plate to stop any converter ballooning and swelling in racing situations. These torque converters are designed for use with a trans-brake and great for power adders such as nitrous, superchargers, and turbos. They are available with various RPM stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss.

Hays Twister Full Race Torque Converters feature a custom designed anti-balloon plate to stop any converter ballooning and swelling in racing situations. These torque converters are designed for use with a trans-brake and great for power adders such as nitrous, superchargers, and turbos. They are available with various RPM stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.