2002 Chevrolet Camaro Performance Exhaust Products

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a rich powerful tone and are the most aggressive, highest performing street muffler we’ve ever built in a four inch case. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a rich powerful tone and are the most aggressive, highest performing street muffler we’ve ever built in a four inch case. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.

The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four-inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

The 80 series is a cross-flow design for applications where the muffler is mounted transversely behind the rear end. Delivering an aggressive muscle car sound both inside and outside the vehicle, this is an excellent replacement for Camaros and Firebirds with transverse mufflers. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.

This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

DynoMax Ultra Flo Welded performance stainless steel mufflers feature 100-percent welded construction for lifelong durability. The unrestricted, straight-through design dyno proven to flow up to 2,000 SCFM and support up to 2,000 horsepower. Each muffler uses our exclusive Continuous Roving Fiberglass (CRF) Technology to absorb unwanted interior resonance while maintaining a deep performance tone. The ‘Pure Unadulterated POWER’ of DynoMax Ultra Flo Welded mufflers are backed by a Limited Warranty and limited Performance & Sound Guarantee.

Product Features:

• Stainless steel construction for lifelong protection
• 100% welded design for maximum durability
• Straight through design ensures unrestricted exhaust flow and reduces back pressure
• CRF Technology absorbs unwanted interior resonance while maintaining a deep performance tone
• Dyno proven to flow up to 2,000 SCFM and support up to 2,000 horsepower.

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four-inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

dBX series mufflers – this Laminar Flow internal configuration muffler features the revolutionary HP core design delivering excellent sound control for a wide variety of engine types where vehicle under-chassis space is limited. Utilizing cool shell technology to minimize radiant heat from the muffler body, they are perfect for sport compact imports as well as muscle cars and other performance applications. Constructed with 409S stainless steel internal components and wrapped with a proprietary insulation material and finally a polishable 304 stainless steel casing, these mufflers are as attractive as they are functional delivering a moderate to aggressive tone.

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

• Manufactured from high-temperature steel core/graphite faced exhaust material
• Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
• Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
• Conforms to and seals minor surface irregularities
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use
• Anti-Stick Properties
• Easy Removal For Disassembly

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

• Withstands Intense Exhaust Heat
• Graphite-Impregnated Facing
• Steel Expanded Metal Core
• Superior Tensile Strength
• Resists Deteriorating
• Anti-stick Properties
• Easy Removal For Disassembly

Multi-Layered Steel (MLS) exhaust and header collector gaskets are designed for extreme cylinder pressures produced by high horsepower high compression turbo-charged, supercharged and nitrous oxide injected engines. Manufactured from three stainless steel layers, they resist corrosion, will not burn through or push out and maintain maximum fastener torque retention. Stress formed inner and outer layer embossments act like springs that rebound under exhaust flange clamp load, creating force to seal extreme exhaust pressures. Total gasket thickness .075 inch. Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.

Product Features:

• Multi Layer Stainless Steel 3-Layers
• Round Port 1.75″ Diameter
• Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.
• Thickness .072″
• Fits GM LS Series Engines 1997-’15

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

• Manufactured from high-temperature steel core/graphite faced exhaust material
• Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
• Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
• Conforms to and seals minor surface irregularities
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use
• Anti-Stick Properties
• Easy Removal For Disassembly

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.

Product Features:

• Withstands Intense Exhaust Heat
• Reusable header, exhaust manifold and collector flange gaskets
• Resists Deteriorating
• Manufactured from “dead soft” aluminum layers – .125″ thick
• Easy Removal For Disassembly
• Conforms easily to surface irregularities (warped flanges)
• Compresses down to 0.060″ to create a tight leak-proof seal
• Will not shrink, deteriorate, or blow out- eliminating gasket leaks
• For high performance street, drag race and oval track use

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Flowmaster’s Scavenger Series Elite long tube headers are designed to replace the restrictive factory cast iron manifolds. These high quality headers are manufactured from stainless steel and are ceramic coated for maximum durability. They feature 1-3/4 in. primary tubes, 3/8 in. thick flanges and incorporate Flowmaster’s popular 3 in. ball flange collector connections, ensuring a leak free installation. Scavenger Series long tube headers deliver maximum performance and are suited to the enthusiast who wants the best. Like all Flowmaster products, the benefits include improved throttle response, power and engine efficiency. Designed for an easy fit, these headers include gaskets and necessary hardware for easy installation. Note 1 – will not fit Saginaw close ratio with 825 power steering box. Note 2 – big block frame stands and motor mounts must be used to ensure proper engine location and header fit. Note 3 – will fit Detroit speed & engineering front sub frames with rack and pinion steering. Note 4 – does not fit with Powerglide transmission. Note 5 – does not fit column shift automatic transmission for Camaro. Note 6 -this product is legal only for off-highway use (except in California or states that have adopted California emission standards), racing use or for use on pre-emission controlled motor vehicles/motor vehicle engines (pre-1966 domestic vehicles certified to California standards, pre-1968 domestic vehicles certified to federal standards and all pre-1968 foreign vehicles), per the application guide.

Product Features:

• Stainless steel construction
• Ball & socket collector connections
• Dyno tuned for maximum performance
• High temperature ceramic coated
• 0.375 thick laser cut flanges

LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• High Performance
• Affordable
• Durable 16 Gauge Material
• Welds Easier
• Lasts Longer
• Heat Cured
• High Heat Resistant

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• Long Tube Lengths
• Long Transition Collectors
• Monstrous Low-Mid Range Torque
• Keep Top End Horsepower
• Provides Finest Fit
• Most Durable Design Available

LS Cast Iron Exhaust Manifold

LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• High Performance
• Affordable
• Durable 16 Gauge Material
• Welds Easier
• Lasts Longer
• Heat Cured
• High Heat Resistant

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• Long Tube Lengths
• Long Transition Collectors
• Monstrous Low-Mid Range Torque
• Keep Top End Horsepower
• Provides Finest Fit
• Most Durable Design Available

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• Long Tube Lengths
• Long Transition Collectors
• Monstrous Low-Mid Range Torque
• Keep Top End Horsepower
• Provides Finest Fit
• Most Durable Design Available

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• Long Tube Lengths
• Long Transition Collectors
• Monstrous Low-Mid Range Torque
• Keep Top End Horsepower
• Provides Finest Fit
• Most Durable Design Available

Hooker Street Force Headers are designed to be a high performance alternative to the stock O.E. manifolds. These headers are built to accommodate all emission control devices. Please check your application in this section for more information regarding emissions legality.

Product Features:

• Long Tube Lengths
• Long Transition Collectors
• Monstrous Low-Mid Range Torque
• Keep Top End Horsepower
• Provides Finest Fit
• Most Durable Design Available

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• Long Tube Lengths
• Long Transition Collectors
• Monstrous Low-Mid Range Torque
• Keep Top End Horsepower
• Provides Finest Fit
• Most Durable Design Available