from

$25.42

Parking Brake Cable

from

$14.59

This wheel disc hardware kit includes rubber components used to protect the caliper pins or bolts. Worn or cracked rubber components will allow excessive movement of guide pins or bolts.

from

$20.00

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

Reduced cost
OE Quality
Complete Kit

from

$20.99

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

Triggers a warning light on the dashboard
Should be replaced each time the brake pad is replaced
Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

from

$173.99

Using advanced re-engineering materials and processes, our master cylinders match O.E. performance and fitment. New O.E.-quality seals and cups are installed on each unit, ensuring leak-free, long-lasting performance. Cast-iron master cylinders are treate

Product Features:

Only new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Bleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Bores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Cast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Piston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Plastic reservoirs are vacuum-tested to ensure they are leak free.

from

$15.08

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$264.24

Bosch is one of the largest global suppliers of automotive products, developing, manufacturing and supplying precision OE components and systems to vehicle manufacturers and the automotive aftermarket.

from

$354.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Our Z26 Street Warrior Brake Upgrade Kit is recommended for high performance, high horsepower muscle and modified cars. This kit comes with everything you need for easy installation, including pads, rotors and stainless-steel hardware. The Drilled & Slotted rotors and Carbon-Fiber Ceramic pads combine to provide shorter stops under the most demanding conditions. This PowerStop Z26 Street Warrior Brake Upgrade Kit is the affordable bolt-on upgrade that delivers more than just the braking power you need to rein in all those ponies. With our low-dust and low-noise formula, you’ll spend less time cleaning those wheels and more time enjoying what matters most – the drive.

Product Features:

This complete brake kit has been engineered to handle the increased demand of street-driven muscle cars and performance vehicles
Proprietary Carbon-Fiber Ceramic Z26 brake pads enhance heat dissipation versus a typical ceramic brake pad for better stopping power at high speed
Stainless-steel pad shims resist the increased temperatures common on high performance applications
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Drilled & Slotted performance rotors provide maximum cooling
Bolt-on upgrade for stock brakes, no modifications necessary
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Brake rotor, pad & hardware engineered to work together to increase stopping power & enhance heat dissipation for your performance car
Rotors are zinc plated for maximum protection against rust.
Includes 1 Front Sensor Wire
Buy with confidence from the originator & industry leader of brake kits

from

$231.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$1.85

The ATE Caliper Guide Pin Cover is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$22.99

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$24.56

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

from

$11.56

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$35.00

Wagner TQ® brake pads feature a zero-copper friction formulation and a unique Integrally Molded Insulator (IMI) technology for quieter operation.

Product Features:

QUIET PERFORMANCE — Semi-metallic friction material engineered in-house to allow quiet operation and high performance
EXCEPTIONAL BRAKING POWER — Advanced friction formulations dissipate heat for superior braking performance
HARDWARE INCLUDED — Premium stainless-steel hardware included for select applications

from

$112.99

Carquest Wearever rotors meet or exceed original equipment specifications while delivering superior stopping power. Carquest Wearever rotors are manufactured with proper harmonic design and non-directional finish that eliminate noise and enhance pedal feel. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of your pads and rotors. Carquest Wearever rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to preventing warping
Air gap eliminates brake fade and increases pad life
Non-directional finish decreases break-in time

from

$11.44

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$66.99

Carquest Platinum Professional brake pads are a premium alternative to original equipment brake pads that provide superior stopping performance, quieter braking and cleaner wheels. All CQ Platinum Professional brake pads are manufactured by a vertically

Product Features:

Industry leading number of application specific formulations for maximum performance and extended pad life
On-vehicle testing similar to original equipment tests
Updated HEX Shim Technology – engineered with aramid fibers to reduce noise and prevent shim wear
Burnishing compound allows for a faster break-in of pads and rotors
PTFE coated hardware and caliper pin grease included for nearly every application
Electronic wear sensors for most applications that require replacement
Electronic wear sensors for most applications that require replacement
Road tested in multiple environments and conditions to ensure reliable stopping power
Meets or exceeds OE specifications and covers 99% of foreign and domestic vehicles
Limited Lifetime Warranty

from

$241.03

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$1.35

Nut

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$26.99

This automotive brake hydraulic hose was precision-engineered to match the fit, function and performance of the original brake hose on specific vehicles and positions to ensure safe, long-lasting durability as part of a complete brake repair.

Product Features:

Ideal replacement – precision-engineered to match the performance of the original brake hose on specific vehicles
Position-specific – manufactured to precise measurements to provide an exact fit and easy installation
Quality assured – materials tested to exacting government-regulated safety and durability standards
Durable design – made with EPDM rubber and specially coated, corrosion-resistant fittings
Brand may vary by location

from

$559.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Our Z26 Street Warrior Brake Upgrade Kit is recommended for high performance, high horsepower muscle and modified cars. This kit comes with everything you need for easy installation, including pads, rotors and stainless-steel hardware. The Drilled & Slotted rotors and Carbon-Fiber Ceramic pads combine to provide shorter stops under the most demanding conditions. This PowerStop Z26 Street Warrior Brake Upgrade Kit is the affordable bolt-on upgrade that delivers more than just the braking power you need to rein in all those ponies. With our low-dust and low-noise formula, you’ll spend less time cleaning those wheels and more time enjoying what matters most – the drive.

Product Features:

This complete brake kit has been engineered to handle the increased demand of street-driven muscle cars and performance vehicles
Proprietary Carbon-Fiber Ceramic Z26 brake pads enhance heat dissipation versus a typical ceramic brake pad for better stopping power at high speed
Stainless-steel pad shims resist the increased temperatures common on high performance applications
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Drilled & Slotted performance rotors provide maximum cooling
Bolt-on upgrade for stock brakes, no modifications necessary
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Brake rotor, pad & hardware engineered to work together to increase stopping power & enhance heat dissipation for your performance car
Rotors are zinc plated for maximum protection against rust.
Includes 1 Front & 1 Rear Sensor Wire
Buy with confidence from the originator & industry leader of brake kits

from

$53.69

WBR Run True Technology Metallurgic-Gray (MG) Finished Rotors All World Brake Resources (WBR) brake rotors with Run-True technology are manufactured to match the exact OE fit, OE construction, and precision finishing to ensure quick and easy installation, as well as trouble-free functionality for the life of the rotor. The Metallurgic-Gray coating is applied to all outward non-friction surfaces including in the gap between the plates covering the cooling vanes and cured through an oven drying process. The Gray coating provides an effective anti-rust protection to help maintain a clean appearance. The coating used for WBR is also similar to the OE color used by many OE car makes. WBR Brake Rotors with Run-True Technology have ultra tight tolerances that provide the finest braking experience, from break in throughout the life of the rotor, reducing the chance of warping even under extreme braking temperatures. The coated brake disc provides a protective water based coating that prevents rust and corrosion, extended rotor life and improved visual appearance. WBR Brake Rotors are manufactured to meet or exceed the original equipment manufacturer specification for durability, fit, and function.

Product Features:

High metallurgical and machining standard to improve stopping distances
Produced to match OE design fitment – G 3000 gray iron
Mill balanced
TS16949 certified
Non-directional finish provides smooth vibration free performance
No need for machining prior to installation
Durable Metallurgic-Gray finish to all outward non-friction surfaces
Metallurgic-Gray anti-rust protection to help maintain a clean appearance
Compatible with NAO, Ceramic and Semi-Met pad compounds for reduced noise
Designed to minimize brake fade and extend pad and rotor life
24/24 Warranty – limited warranty against defects in material and workmanship Technical Service Bulletins

from

$18.49

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. Caliper Guide Pins are important to replace because they hold the brake piston in place to create effective stopping performance.

Product Features:

This part matches Original Equipment (OE) quality specifications
Easy and fast replacement
Helps deliver a quieter, more efficient braking system
Corrosion resistant coating for long-lasting durability against harsh roads
Manufactured with quality materials to suppress high stress levels

from

$89.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$32.49

WJB Automotive wheel hub assemblies are made with high precision through state-of-the-art technology and manufactured with strict quality-control criteria. Every wheel hub assembly is specifically designed to fit the designated applications and may be used as a direct replacement for the original part. Each part is engineered using OE data and measurements to ensure fitment, performance, and longevity.

Product Features:

Fitment and function are ensured by precision machining, rigorous testing, and meticulous inspection of material and components.
WJB Automotive wheel hub assemblies are designed to meet stringent fatigue requirements in order to reduce premature failure.
Reinforced seal design material allows for optimal performance in harsh environments.
WJB Automotive wheel hub assemblies undergo heat treatment and cold-forming processes that harden the surface ensuring high-temperature resistance and durability.
Where applicable, pre-installed speed sensors will automatically sync to the vehicle’s anti-lock braking system upon successful installation and provide accurate speed-reading data.
Brand may vary by location