Name: Pre-Pressed Rear Axle
Brand: Dorman
SKU: 926-177
Price: 1116.99 USD

from

$1116.99

Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.

Product Features:

Pre-Pressed Rear Axle
Pre-Pressed Rear Axle
Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.
Easier installation – this loaded axle assembly includes a pre-assembled new axle shaft, wheel bearing, hub and backing plate
Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components

from

$12.29

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$107.99

When the thin-gauge steel corrodes on Sequoia, Tacoma, Tundra truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.

Product Features:

Rear Differential Cover
Rear Differential Cover
When the thin-gauge steel corrodes on Sequoia, Tacoma, Tundra truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.
Direct replacement – this weld-on differential cover directly replaces a corroded original cover on certain Sequoia, Tacoma and Tundra trucks
Cost-effective repair – rather than buy a new axle, cut off the old cover and weld on this new one

from

$292.99

Product Features:

TOY 12BLT 8.25 R/P 4.88 MG

from

$406.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. Includes side shims.

Product Features:

Fits reverse rotation Toyota 7.5″ front
Included are Timken bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and silicone.

from

$19.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$364.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, pinion shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket. .

Product Features:

Fits reverse rotation Toyota 7.5″
Uses Koyo bearings and races
Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, pinion shim kit, ring gear bolts, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and silicone.

from

$73.99

Product Features:

Cross pin shaft
Fits Toyota Tacoma and T100

from

$15.99

Toyota T100 & Tacoma pinion nut.

Product Features:

Pinion nut
Fits Toyota Tacoma and T100 without factory locking differential

from

$8.99

Product Features:

Roll pin
Fits Toyota Tacoma and T100

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$18.99

Product Features:

Side gear thrust washer
Fits Toyota Tacoma and T100

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$7.99

07 & up Tundra & Sequoia front ring gear bolt..

Product Features:

Ring gear bolt
Fits 2007 and up Toyota Tundra front

from

$42.99

Product Features:

TOYOTA 8″ V6&4CLY TURBO

from

$7.11

Pinion Seal

from

$93.99

7.5″ V6 & 4cyl side shim kit (incl. 7 shims).

Product Features:

Carrier shim kit
Fits Toyota 7.5″

from

$389.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Toyota Tacoma and T100 without factory locking differential
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$24.99

Product Features:

Pinion gear thrust washer
Fits Toyota Tacoma and T100

from

$634.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 7.5″
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$925.99

Differential

from

$20.29

Product Features:

CRUSH SLEEVE TOY. FRT END

from

$37.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$13.49

Product Features:

KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT

from

$27.99

Pinion preload shim for Toyota T100. One single shim. 0.033″ thick. Two needed. Fits against crush sleeve.

Product Features:

Fits Toyota T100 and Tacoma
0.140″ thick

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes