2001 Chevrolet Malibu Ignition Wires

Ignition Wire Holder

ACDelco GM Original Equipment Spark Plug Wire Sets consist of a set of wires, encased in an insulating material, connectors, and insulating boots, and are GM-recommended replacements for your vehicle’s original components. The wires transfer high voltage pulses between the voltage source, the distributor, and the spark plug. These original equipment wires have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Durable to help transfer high voltage pulses without damage
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

NGK ultra-low resistance mag core wire sets provide outstanding performance and durability. High-temp premium silicone outer jacket and inner EPDM/silicone insulation contain high voltage currents for excellent dielectric strength. Stainless steel winding

Product Features:

• PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
• BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
• STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
• CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• 40 ft. Of Conductor Wound Into A Single Foot Of Wire
• For high EMI suppression
• Conductor core features Dupont Kevlar material
• Proprietary compound sleeves for resistance to high heat/abrasion

NGK ultra-low resistance mag core wire sets provide outstanding performance and durability. High-temp premium silicone outer jacket and inner EPDM/silicone insulation contain high voltage currents for excellent dielectric strength. Stainless steel winding

Product Features:

• PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
• BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
• STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
• CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

Routing spark plug wires is an art form. It takes patience and time to route your wires away from the headers, through separators and to the distributor cap. Some wire sets fit perfect, but a lot of people want to build their own so they can route them exactly how they see fit. Our Universal spark plug wire sets come with the spark plug terminal and boot installed with the other end open. Distributor cap boots and terminals are included so you can cut the wire to the desired length, then install the terminal with the supplied Mini-Stripper-Crimper. It’s a little more work, but in the end it will be worth it.

Product Features:

• Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
• Distributor Cap – Boots and Terminals Included
• Incl. Mini-Stripper-Crimper

These ACCEL Super Stock wire sets are a true performance upgrade replacement for OE types. Efficient delivery of spark energy for a good price. Silicone boots with zinc-plated steel terminals.

Product Features:

• 500 Ohms Per Foot Of Resistance
• 550 Degree F Rated Silicone Jacket
• Stainless Steel Plug Terminals
• High RFI Suppression For Street/Strip Use
• Custom Fit Universal and Import Coverage
• High-strength Fiberglass Braid Construction
• Pre And Post HEI Vehicles

Product Features:

• SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
• Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
• 100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
• EPDM inner insulation stops power-robbing voltage leaks.
• With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
• Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
• Excellent interference suppression and consistent performance
• Easy lock terminals for more convenient installation.
• Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
• Broad coverage available for most vehicles on the road today
• Include grease pack to ensure easy installation and removal

Pre-Greased Spark Plug Boots for Quicker Installation; Delphi Packard-marked Cable for OE Component Confirmation; OE Boots, Terminals, and Lead Lengths for No Hassle Installation; Application Correct Seven and Eight Millimeter Cable Sizes for Correct Fit

Product Features:

• Pre-greased spark plug boots for quicker installation
• OE boots, terminals and lead lengths for no hassle installation

NGK Coil on Plug Boots are built to stringent OEM tolerances, combining original equipment fit, design and outstanding durability. NGK Coil on Plug Boots are manufactured using only premium silicone and always include any required internal springs and ferrite resistors for superior performance and RFI noise suppression. Bridging the important link between ignition coil and spark plug, COP boots should always be replaced with NGK Coil on Plug Boots at the time as changing spark plugs to prevent ignition problems such as flashover.

Product Features:

• PREMIUM GRADE SILICONE: Designed to withstand harsh environments
• OEM MATCHED: Includes all required internal springs and ferrite resistors for superior performance and RFI noise suppression

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

ACDelco Professional Spark Plug Wire Sets consist of a set of wires, encased in an insulating material, connectors, and insulating boots, and are a high quality replacement for many vehicles on the road today. The wires transfer high voltage pulses between the voltage source, the distributor, and the spark plugs. These premium aftermarket replacement components are manufactured to meet your expectations for fit, form, and function.

Product Features:

• Professional, premium aftermarket replacement
• Provides the performance and dependability you expect from ACDelco
• Manufactured to meet expectations for fit, form, and function

Pre-Greased Spark Plug Boots for Quicker Installation; Delphi Packard-marked Cable for OE Component Confirmation; OE Boots, Terminals, and Lead Lengths for No Hassle Installation; Application Correct Seven and Eight Millimeter Cable Sizes for Correct Fit

Product Features:

• Pre-greased spark plug boots for quicker installation
• OE boots, terminals and lead lengths for no hassle installation

NGK ultra-low resistance mag core wire sets provide outstanding performance and durability. High-temp premium silicone outer jacket and inner EPDM/silicone insulation contain high voltage currents for excellent dielectric strength. Stainless steel winding

Product Features:

• PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
• BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
• STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
• CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

For mounting on non-stock applications, for remote location. Choice of 4 core types. Female and male distributor towers. Terminal crimper and anvil tools. Includes silicone lube, boots and terminals. 20 piece kit.

Product Features:

• 150 Ohms Per Foot
• 600° F Rated Silicone Jacket
• Stainless Steel Plug Terminals
• Custom-fit Universal And Import Coverage
• Pre And Post HEI Vehicles
• Spiral-Wound Copper/Nickel Alloy

Product Features:

• SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
• Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
• 100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
• EPDM inner insulation stops power-robbing voltage leaks.
• With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
• Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
• Excellent interference suppression and consistent performance
• Easy lock terminals for more convenient installation.
• Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
• Broad coverage available for most vehicles on the road today
• Include grease pack to ensure easy installation and removal

Designed to be an ideal replacement for your vehicle’s worn equipment, ACDelco Professional, premium aftermarket Auto Wire and Auto Cable products are built to meet nearly every application and budget. ACDelco meet or exceed most original manufacturers’ specifications. Built to exacting specifications, and extensively tested, ACDelco Auto Wires and Auto Cables includes our Original Equipment line for GM vehicles and a select offering of premium aftermarket Professional products for GM and non-GM vehicles. ACDelco Professional, premium aftermarket Direct Ignition Coil-on-Plug Boots seal snugly against the spark plug’s insulator, keeping moisture and contaminates out and promoting longer spark plug life. They are thoroughly engineered to meet or exceed your expectations for fit, form, and function. ACDelco Professional Direct Ignition Coil-on-Plug Boots provide the performance and dependability you expect from ACDelco.

Product Features:

• Weather tight boot seal for protection against moisture intrusion
• High temperature resistant silicone for protection against thermal overload
• Stainless steel internal spring with resistor to suppress RFI and deliver maximum voltage to the spark plug
• Premium, high-quality aftermarket spark plug boot Signs that you might need to replace your direct ignition coil-on-plug boot are:
• Engine will not start or run
• Reduced Power
• Excessive tailpipe emissions
• Check Engine Light is on
• Engine misfire
• Reduced fuel economy

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• 40 ft. Of Conductor Wound Into A Single Foot Of Wire
• For high EMI suppression
• Conductor core features Dupont Kevlar material
• Proprietary compound sleeves for resistance to high heat/abrasion

The Prestolite carbon core wire set is resistant to fuels, oils and other under-hood chemicals and utilizes a stainless steel or zinc-plated steel for optimum strength, electrical conductivity, and corrosion resistance.

Product Features:

• OE-Equivalent and Direct fit for easy Installation.
• OE style connectors.
• Resistant to high temperatures, corrosion and vibration.
• Ignition noise suppressed. The Prestolite Ignition Wire Set features identical fit, function, color, and performance to OE.

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• 40 ft. Of Conductor Wound Into A Single Foot Of Wire
• For high EMI suppression
• Conductor core features Dupont Kevlar material
• Proprietary compound sleeves for resistance to high heat/abrasion

Built to match the Original Equipment in length and fit, ACDelco Professional Ignition Wire Sets also offer a performance advantage over many aftermarket products.

Product Features:

• Designed to match Original Equipment wire sets in critical areas such as cable length and diameter, terminal design and insulator position.
• Have broad coverage available for most vehicles on the road today from 1980 to present.
• Provide a high degree of Radio Frequency Interference (RFI) suppression.
• Are designed to offer fit, form and function for optimum performance.
• Kevlar®-reinforced fiberglass core in select sets for increased strength.
• Core sheathed in radio-static-absorbent material for increased RFI suppression.
• Wire-wound, stainless-steel alloy conductor for maximum spark delivery and RFI suppression on most applications.
• A layer of conductive heat-resistant latex for added durability.
• Insulating rubber-based compound inner jacket helps minimize voltage drop and enhance durability.
• Thick silicone outer jacket for excellent heat resistance.

For mounting on non-stock applications, for remote location. Choice of 4 core types. Female and male distributor towers. Terminal crimper and anvil tools. Includes silicone lube, boots and terminals. 20 piece kit.

Product Features:

• 150 Ohms Per Foot
• 8.8mm Oversize Silicone Jacket
• Stainless-Steel Spark Plug Terminals
• Suppression of EMI/RFI
• 600-Degree Double Silicone Construction
• Spiral-Wound Copper/Nickel Alloy

For engines with late-model type (HEI spark plug top) distributor caps. Multi-angle boots and terminals installed on one end. 90 degree distributor boots and terminals included.

Product Features:

• Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
• Distributor Cap – Boots and Terminals Included
• Includes Mini-Stripper-Crimper For Factory Style Crimps
• Size Includes [8] 90 Degree Boots/Terminal Ends
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

Product Features:

• SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
• Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
• 100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
• EPDM inner insulation stops power-robbing voltage leaks.
• With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
• Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
• Excellent interference suppression and consistent performance
• Easy lock terminals for more convenient installation.
• Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
• Broad coverage available for most vehicles on the road today
• Include grease pack to ensure easy installation and removal

ACDelco Professional Spark Plug Wire Sets consist of a set of wires, encased in an insulating material, connectors, and insulating boots, and are a high quality replacement for many vehicles on the road today. The wires transfer high voltage pulses between the voltage source, the distributor, and the spark plugs. These premium aftermarket replacement components are manufactured to meet your expectations for fit, form, and function.

Product Features:

• Professional, premium aftermarket replacement
• Provides the performance and dependability you expect from ACDelco
• Manufactured to meet expectations for fit, form, and function

Set includes terminals for engines with early type (socket) and late type (HEI spark plug top) distributor caps. 90 degree boots and terminals factory installed on one end.

Product Features:

• Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
• Incl. both socket-style and spark plug-style boots and terminals
• Includes Mini-Stripper-Crimper For Factory Style Crimps
• Size Includes [6] 90 Deg. Boots/Terminals
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications
• Bolt-on Performance
• Conductor core features DuPont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately