1999 Infiniti I30 Belts and Hoses
More 1999 Infiniti I30 Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1999 Infiniti I30, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1999 Infiniti I30 Belts and Hoses
Gates – Premium Molded Coolant Hose (Part No.22183)
from
$32.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 17 Inch Length (Part No.88402)
from
$49.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium 5/16 X 50 Ft Heater Hose by Gates (sold by each) (Part No.28408)
from
$1.79
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time
- Similar to SAE 20R3 Class D-3
- Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications.
Dayco – Dayco, Heater Hose, Trim-to-Fit (Part No.R30301220370DAY)
from
$12.45
Dayco, Heater Hose, Trim-to-Fit
Bando – Multi Rib (Serpentine) Belt (Part No.W100057556BAN)
from
$18.62
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Strong tensile cords limit stretching.
- Supports higher horsepower loads.
- Made from high strength synthetic rubber.
Bando – Multi Rib (Serpentine) Belt (Part No.W100026491BAN)
from
$11.09
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Strong tensile cords limit stretching.
- Supports higher horsepower loads.
- Made from high strength synthetic rubber.
Bando – Multi Rib (Serpentine) Belt (Part No.W100065195BAN)
from
$21.01
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Strong tensile cords limit stretching.
- Supports higher horsepower loads.
- Made from high strength synthetic rubber.
Driveworks – Poly Rib Belt Serpentine Belt; 43.11 Long, 6 Rib Count (Part No.431K6)
from
$33.49
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Driveworks – Poly Rib Belt Serpentine Belt; 43.6 Long, 6 Rib Count (Part No.436K6)
from
$21.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Gates – Micro-V« Serpentine Drive Belt (Part No.K040305)
from
$31.99
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.
Product Features:
See More
Product Features:
- Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
- EPDM rubber constructions resist cracking on the rib surface
- Meets or exceeds all specifications from the Original Equipment Manufacturer
- Tensioner Replacement is Recommended (if equipped)
- Unique form grinding of each individual belt assures precise dimensional control.
- Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 84mm Dia., 25mm Width, Smooth (Part No.89134)
from
$40.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 84 mm Diameter (Part No.900175A)
from
$66.99
This pulley is designed and engineered by Litens Automotive the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made using the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction for long life and trouble-free performance. Designed for Nissan/Infinity/Mitsubishi applications. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Dorman – Idler/Tensioner Pulley: Specific Fit, Steel, 84 mm Diameter (Part No.419-624)
from
$68.99
This replacement accessory drive belt idler pulley has been engineered to match the function and performance of the original pulley on select vehicle years, makes and models, properly restoring critical vehicle operations.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt idler pulley matches the fit and function of the original equipment pulley on specified vehicles
- Restores performance – fixes a failed, squealing or groaning noise from a worn idler pulley
- Application specific – reverse engineered from the original design on certain vehicle years, makes and models
- Trustworthy quality – backed by team of engineers and quality specialists in the United States
Gates – DriveAlign« Belt Drive Idler/Tensioner Pulley (Part No.36087)
from
$46.99
Gates is a leading manufacturer of Original Equipment (OE) idler pulleys. Gates DriveAlign(R) Idler Pulleys meet or exceed OE specifications. High quality, high strength bearings run cooler and last longer than original bearings. DriveAlign Idler Pulleys are built to last by resisting dirt, salt, and other under-hood contaminants. Designed for use on automobiles and light trucks as locked center tensioning, automatic belt tensioning and idler pulleys.
Product Features:
See More
Product Features:
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
Dayco – Serpentine Belt Kit; With 2 Belts and Pulley, 3 Piece Set (Part No.5060431K1)
from
$51.99
Dayco believes in a systems approach to maintenance and has a full line of serpentine belt kits that have been designed for the most popular light-duty applications, ensuring that whomever is completing the repair has all the parts needed. Dayco’s kit offers everything to service your front-end accessory drive with OE or equivalent components. This can include a premium tensioner with flat spring technology, durable pulley(s) with permanently lubricated bearings, a Dayco ela (stretch) serpentine belt, and the Dayco serpentine belt that provides extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Engineered to match OE specifications with unique features that enhance vehicle performance and safety
- For vehicles that need a highly engineered drive belt and multiple parts for a thorough and proper repair
- Provides all the parts needed in one box, helping simplify installation
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13" Long, 1.34" Diameter (Part No.C71794)
from
$25.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.22184)
from
$62.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.34" Diameter (Part No.C71795)
from
$44.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia. (Part No.81041)
from
$14.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Molded Heater Hose; EPDM Rubber, 9/32 Inch Diameter, 5 Inch Length (Part No.86815)
from
$8.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Molded 90 Degree Heater Hose (Part No.28474)
from
$14.79
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
Product Features:
See More
Product Features:
- Resists electrochemical degradation and water permeation
- Use with heater hose connectors and bulk heater hose to create custom assemblies
- Compatible for coolant, air and water applications
- EPDM tube and cover, synthetic fiber reinforcement
- SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
- Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.25" Inside Diameter (Sold by foot) (Part No.28407)
from
$0.99
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Popular 1999 Infiniti I30 Belts and Hoses Categories
1999 Infiniti I30 Belts and Hoses
You count on your 1999 Infiniti I30 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 30 Belts and Hoses ranging in price from $0.99 to $68.99, you’re sure to find everything you need for your 1999 Infiniti I30.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 6 different brands like Dayco, Driveworks, and Dorman. 1999 Infiniti I30 Belts and Hoses start as low as $0.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 292 extensive product reviews on 1999 Infiniti I30 Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia. with 3.0 stars and Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.34" Diameter with 4.5 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1999 Infiniti I30 below to get started!
Top-Rated Belts and Hoses Brands For Your 1999 Infiniti I30
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1999 Infiniti I30 running right for years to come. In our inventory you’ll find brands like Dayco, Driveworks, Dorman, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 1999 Infiniti I30 back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1999 Infiniti I30, and some of our most reviewed Dayco parts include:
from
$25.99
(184)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13" Long, 1.34" Diameter
Coolant Hoses
FAQs for 1999 Infiniti I30 Belts and Hoses
What are the most purchased Belts and Hoses for the 1999 Infiniti I30?
Out of 30 Belts and Hoses for the 1999 Infiniti I30, the most popular in our inventory are:
from
$40.99
(10)
Serpentine Idler/Tensioner Pulley; Steel, 84mm Dia., 25mm Width, Smooth
Drive Belt Idler Assemblies
from
$1.79
This product is not rated
Premium 5/16 X 50 Ft Heater Hose by Gates (sold by each)
Heater Hoses
What are the top-rated 1999 Infiniti I30 Belts and Hoses?
Top-rated Belts and Hoses for your 1999 Infiniti I30 based on customer reviews/ratings are:
from
$14.99
(8)
Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia.
“first time i have bought these…..so we will see”
from
$44.99
(4)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.34" Diameter
“Work’s as it should. Great quality.”
from
$27.49
(3)
Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 7-1/2 Inch Length
“Worked and fit just fine! It’s a gasket, not more to say!”
