1999 GMC C3500 Differentials

Essential 1999 GMC C3500 Differentials

Yukon Gear – Bearing Race Driver (Part No.56020)

Bearing Race Driver

from

$215.99
Bearing race driver. No return.

Product Features:
  • Bearing race driver
  • Fits M802011 race
  • All steel construction
See More

Yukon Gear – Pilot Bearing For 10.5" 14 Bolt Truck, 2.050" O.D. (Part No.18041)

Pilot Bearing For 10.5" 14 Bolt Truck, 2.050" O.D.

from

$57.99
Pilot bearing for 10.5″ 14 bolt truck, 2.050″ O.D.

Product Features:
  • Pilot bearing
  • Fits GM 10.5″ 14 bolt truck
  • 2.050″ O.D.
See More

Yukon Gear – Replacement Baffle For Dana 60 & Dana 70-U (Part No.33001)

Replacement Baffle For Dana 60 & Dana 70-U

from

$6.99
Product Features:
  • Oil baffle for Dana Spicer 60 and Dana Spicer 70U
See More

Valvoline – DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.822405)

DEXRON - VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart

from

$14.49
Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:
  • Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
  • Enhanced anti-shudder protection for smooth shifting and maximum power transfer
  • Developed with anti-wear technology to help improve transmission durability
  • Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
See More

Yukon Gear – Pinion Install Kit For ’99 & Newer 10.5" GM 14 Bolt Truck Differential (Part No.13106)

Pinion Install Kit For '99 & Newer 10.5" GM 14 Bolt Truck Differential

from

$449.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:
  • Fits 1998 and up GM 10.5″ 14 bolt truck
  • Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.
See More

Yukon Gear – Replacement Pinion Nut Washer For Dana 80 (Part No.33165)

Replacement Pinion Nut Washer For Dana 80

from

$5.99
Product Features:
  • Pinion nut washer
  • Fits Dana Spicer 80
See More

Pro-King – Differential Ring Gear Bolt (Part No.744A935)

Differential Ring Gear Bolt

from

$1.89
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:
  • All products are designed to meet or exceed OE quality, form, fit and funtion.
See More

Richmond Gear – Differential Spool (Part No.81-1028-1)

Differential Spool

from

$259.99
Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:
  • For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
  • The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
  • Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
  • Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
  • Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.
See More

Driveworks – Tapered Roller Bearing (Part No.S-HM-807010)

Tapered Roller Bearing

from

$17.29
Product Features:
  • Brand may vary by location
See More

Dorman – Rear Axle Shaft, Left or Right (Part No.630-136)

Rear Axle Shaft, Left or Right

from

$339.99
Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:
  • Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models.
  • Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications.
  • Durable construction – designed to rigorous standards and tested to ensure performance
  • Trustworthy solution – backed by team of engineers and quality control specialists in the United States
See More

Yukon Gear – Dana 50 Dana 60 Dana 70 & Dana 80 Roll Pin, 0.225" Dia, For X/P Shaft, 1.87" Lng (Part No.33327)

Dana 50 Dana 60 Dana 70 & Dana 80 Roll Pin, 0.225" Dia, For X/P Shaft, 1.87" Lng

from

$7.99
Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:
  • Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
  • 0.225″ diameter
  • 1.870″ long
See More

Yukon Gear – Replacement Pinion Depth Shims For Dana 80 (Part No.55024)

Replacement Pinion Depth Shims For Dana 80

from

$79.99
Product Features:
  • Pinion depth shim kit
  • Fits Dana Spicer 80 4.125″ design
See More

Felpro – Differential Cover Gasket (Part No.RDS 55063)

Differential Cover Gasket

from

$6.79
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Unsurpassed quality you can trust
  • Validated for fit, form and function
  • Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
See More

Yukon Gear – DiffrlPinSupportBolt (Part No.33582)

DiffrlPinSupportBolt

from

$5.99
DiffrlPinSupportBolt

Motive Gear – Differential Gear Install Kit (Part No.GM10.5IK-2)

Differential Gear Install Kit

from

$44.49
All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!
See More

Yukon Gear – Standard Open Carrier Case, GM 10.5" 14 Bolt Truck, 4.10 & Down (Part No.20100)

Standard Open Carrier Case, GM 10.5" 14 Bolt Truck, 4.10 & Down

from

$729.99
Product Features:
  • Standard open carrier case
  • Fits GM 10.5″ 14 bolt truck
  • 4.10 and down ratio only
  • Does not include spider gears
See More

Motive Gear – Differential Pinion Seal (Part No.9316)

Differential Pinion Seal

from

$16.49
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.
See More

Yukon Gear – Crush Sleeve Eliminator Kit For GM 10.5" 14 Bolt Truck (Part No.55067)

Crush Sleeve Eliminator Kit For GM 10.5" 14 Bolt Truck

from

$121.99
Crush sleeve eliminator kit for GM 10.5″ 14 bolt truck. This kit contains a solid spacer & shim kit to eliminate the crush sleeve and set pinion bearing preload.

Product Features:
  • Crush sleeve eliminator kit for GM 10.5″ 14 bolt truck
See More

Motive Gear – Differential Ring and Pinion (Part No.GM10.5-373)

Differential Ring and Pinion

from

$268.99


Product Features:
  • GM 14BL 10.5 R/P 3.73 MG
See More

Dorman – Differential Pinion Yoke Assembly (Part No.697-545)

Differential Pinion Yoke Assembly

from

$313.99
Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:
  • Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
  • Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
  • Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
  • Validated fit – this differential end yoke has been tested to confirm accurate fit
See More

Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 70, 70HD, 70U & 80 (Part No.55011)

Replacement Carrier Shim Kit For Dana 60, 70, 70HD, 70U & 80

from

$13.99
Product Features:
  • Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80
See More

Yukon Gear – Polished Aluminum Cover For 10.5" GM 14 Bolt Truck (Part No.32028)

Polished Aluminum Cover For 10.5" GM 14 Bolt Truck

from

$269.99
Polished aluminum cover for 14T GM.

Product Features:
  • Fits GM 10.5″ 14 bolt truck
  • Finned polished aluminum
See More

Yukon Gear – Differential Cover B (Part No.33572)

Differential Cover B

from

$7.99
Differential Cover B

USA Standard Gear – Master Overhaul Kit for the GM 10.5" 14T Differential, ’89-’98 (Part No.37045)

Master Overhaul Kit for the GM 10.5" 14T Differential, '89-'98

from

$309.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:
  • Fits 1989-1997 GM 10.5″ 14 bolt truck
  • Uses Koyo bearings and races
  • Included are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.
See More

Yukon Gear – Dura Grip Positraction For 10.5" GM 14 Bolt Truck, 4.10 & Down (Part No.26030)

Dura Grip Positraction For 10.5" GM 14 Bolt Truck, 4.10 & Down

from

$1110.00
The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:
  • Fits GM 10.5″ 14 bolt truck
  • 4.10 ratio and down only
  • Clutch style positraction
  • Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
  • Fully rebuildable
  • Assembled in the USA
See More

Yukon Gear – 14T Pinion Gear Thrust Washer (Part No.33384)

14T Pinion Gear Thrust Washer

from

$8.99
14T pinion gear Thrust washer.

Product Features:
  • Pinion gear thrust washer
  • Fits GM 10.5″ 14 bolt truck
See More

Yukon Gear – Side Gear Thrust Washer For Dana 60, 70 & 80 (Part No.33532)

Side Gear Thrust Washer For Dana 60, 70 & 80

from

$4.99
Product Features:
  • Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
  • Fits standard open differentials only
See More

Yukon Gear – 14T Side Gear Thrust Washer (Part No.33383)

14T Side Gear Thrust Washer

from

$7.99
14T side gear Thrust washer.

Product Features:
  • Side gear thrust washer
  • Fits GM 10.5″ 14 bolt truck
See More

1999 GMC C3500 Differentials

Maybe you’re in the middle of a full rebuild of that 1999 GMC C3500. Maybe you just need a couple of Differentials. Either way, Advance Auto Parts has 248 different Differentials in our inventory ranging from $1.89 to $2,324.99. That means you can find the exact parts or products you need to keep that 1999 GMC C3500 running smoothly.

Differentials are only as good as their brand. We stock 18 different brands to make sure you have plenty of trusted parts to choose from for your 1999 GMC C3500. Valvoline, Driveworks, and Yukon Gear are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Differentials for your 1999 GMC C3500, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 1,358 reviews in this category, some of the top rated parts include Bearings with 3.9 stars and Multi Purpose Seal with 4.2 stars.

So if you’re in the market for aftermarket Differentials to keep your 1999 GMC C3500 rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Differentials Brands To Make Your 1999 GMC C3500 Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1999 GMC C3500 demands trusted brand parts and products to keep it running. Many trusted brands of Differentials make up Advance Auto Parts’ inventory, and all are ready to help make your C3500 the best it can be. Be sure to browse some of our top Differentials brands and parts.

Top 1999 GMC C3500 Differentials from Dorman

Dorman products are another trusted brand when it comes to Differentials for your 1999 GMC C3500. Popular Dorman parts include:
Ring and Pinion Bearing Installation Kit
from $282.99
(255)
Ring and Pinion Bearing Installation Kit
Differential Bearing Kits
Rear Differential Cover
from $36.99
(15)
Rear Differential Cover
Differential Covers

FAQs for 1999 GMC C3500 Differentials

What are the most purchased Differentials for the 1999 GMC C3500?

Out of 248 Differentials for the 1999 GMC C3500, the most popular in our inventory are:
Tapered Cone/Cup Wheel Bearing Set
from $13.99
(14)
Tapered Cone/Cup Wheel Bearing Set
Front Differential Pinion Bearings
Differential Cover Gasket
from $6.79
(13)
Differential Cover Gasket
Rear Differential Cover Gaskets
3 Qt - 80W90 Conventional Gear Oil With Posi Additive
from $57.99
This product is not rated
3 Qt – 80W90 Conventional Gear Oil With Posi Additive
Differential Oil

What are the top-rated 1999 GMC C3500 Differentials?

Top-rated Differentials for your 1999 GMC C3500 based on customer reviews/ratings are:
Bearings
from $23.99
(7)
Bearings
“Good price”
Multi Purpose Seal
from $44.99
(5)
Multi Purpose Seal
“How do you fix a leaking rear end? You seal it. That’s why I bought this seal.”
Taper Bearing Set
from $13.79
(4)
Taper Bearing Set
“Worked great on my 1981 Chevy C20”