1999 GMC C2500 Performance Engines

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

This Holeshot 2400 fits all 1998-02 GM Camaro/Firebirds w/LS1 engine, 1999-up GM1500 trucks and SUV’s with 4.8L, 5.3L, or 6.0L engine and 4L60E or 4L65E transmission. This converter retains the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2400 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Will Not fit 1997-05 Corvette. Has both 10.75 and 11.08-inch bolt circles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Inside tang-to-taper relationship held tightly for repeatable valve spring installed heights

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Edelbrock Water Pump Cartridge for Small-Block Chevy (Race Style), 8827.

Edelbrock No: 7252 Engine Water Pump Gasket Set No: 7252 Chevy Big Block. Is it time to rebuild your Edelbrock mechanical water pump- No problem- these Edelbrock water pump gaskets will keep your water pump leak-free. They are manufactured from quality materials and can be installed easily without any modifications

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

The POWERAID Throttle Body Spacer is designed to enhance off-idle torque from 800 rpm to approximately 3,000 rpm. The spacer utilizes it’s unique, patented Helix Bore design to spin the incoming air charge as it passes through the throttle body spacer. The spinning air action boosts the velocity of the incoming air And contributes to better atomization of the air/fuel mixture as the air charge enters the combustion chamber. The end result is more part-throttle torque And improved mid-range power.

High performance street, stock converter ok, best with 2000+ converter and gears, choppy/thumping idle.

HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Edelbrock part No: 6997 Front Timing Cover Gasket set for Small-Block Chevy. Includes front cover gasket and front seal.

If you are changing your camshaft or replacing the timing set, make sure to replace this seal at the same time! Made from Nitrile rubber.

Edelbrock part #2104 Performer intake manifold is designed for street 262-400 c.i.d. Chevy V8’s that have heads with canted center bolt holes, 1987-1995. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response. The Performer intake manifolds are ideal for passenger cars, trucks, 4x4s, tow vehicles and RVs. For 1987-95 stock aluminum heads use #2101.

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermo conductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually. Gasket bore 4.100 inch, Compressed thickness 0.028 inch

The Edelbrock No: 7361 head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit and sealing properties when used with Edelbrock aluminum cylinder heads. Edelbrock head gaskets are manufactured from high-density materials and feature a superior design that performs under pressure and provides a long-lasting seal, without re-torqueing.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Edelbrock Valve Spring Retainers are made of superior quality steel and are machined and heat treated for maximum strength. They feature a black oxide finish to prevent rust and corrosion

Competition Cams Steel Retainer for Ford 4.6L 3 Valve with 26113/26125 Beehive Springs, 710-1.

“Competition Cams Tool Steel 10 Degree Retainer For All Valves With 1.250″” O.D. Springs, 1750-1. ”