1997 Chevrolet Corvette Torque Converter and Related Products

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

You can forget about the problem of shearing a torque converter bolt after you install these super strong 200,000 Pounds Per Square Inch gems. They are designed for each specific application and provide the optimum grip. Kits come with hardened parallel ground washers.

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

The Tork Master 2000 fits 1984-93 GM TH700R4/4L60 with 30 spline input and 1993-96 4L60E with 30 spline input. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft-lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide, or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

Hays Twister 3/4 Race Torque Converters–Good names never go away, and neither should good terms!

Hays Twister Full Race Torque Converters feature a custom designed anti-balloon plate to stop any converter ballooning and swelling in racing situations. These torque converters are designed for use with a trans-brake and great for power adders such as nitrous, superchargers, and turbos. They are available with various RPM stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss.

Hays Twister Full Race Torque Converters feature a custom designed anti-balloon plate to stop any converter ballooning and swelling in racing situations. These torque converters are designed for use with a trans-brake and great for power adders such as nitrous, superchargers, and turbos. They are available with various RPM stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss.

Hays Twister 3/4 Race performance torque converters are a perfect addition to our line of performance flexplates, clutches, and flywheels. Our 3/4 Race series of torque converters is intended for street/strip combinations, with various stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss. The Twister 3/4 Race torque converter perfectly describes a converter suited for an application just shy of Full Race converter.

Hays 3/4 Race Converters! PERFORMANCE PARTS>PERFORMANCE DRIVELINE>DRIVETRAIN PARTS>TORQUE CONVERTERS from Hays

This HoleShot 3000 fits 1984-93 GM 700R4/4L60 automatic transmissions with 30 spline input shaft. This converter does not retain the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 3000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace-brazed impeller fins and turbine, a new precision alloy impeller hub, and new heavy-duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate-type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide, or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Does Not fit 4L60E transmissions. Both 10.75 and 11.50-inch bolt circles

Hays Twister 3/4 Race Torque Converters–Good names never go away, and neither should good terms!

Hays Twister 3/4 Race Torque Converters–Good names never go away, and neither should good terms!

Hays Twister 3/4 Race performance torque converters are a perfect addition to our line of performance flexplates, clutches, and flywheels. Our 3/4 Race series of torque converters is intended for street/strip combinations, with various stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss. The Twister 3/4 Race torque converter perfectly describes a converter suited for an application just shy of Full Race converter.

Hays Twister 3/4 Race performance torque converters are a perfect addition to our line of performance flexplates, clutches, and flywheels. Our 3/4 Race series of torque converters is intended for street/strip combinations, with various stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss. The Twister 3/4 Race torque converter perfectly describes a converter suited for an application just shy of Full Race converter.

This Holeshot 2400 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-97 4L60E w/30 spline input, and 1997-04 Corvette transmissions. This converter retains the lockup feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2400 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace-brazed impeller fins and turbine, a new precision alloy impeller hub, and new heavy-duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, and less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide, or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

Pro-King is the leading supplier of transmission and driveline products in the aftermarket. All products are designed to meet or exceed OE quality, form, fit and function.