1996 Dodge B2500 Differentials

Pinion nut for Chrysler 7.25″, 8.0″ IFS, 8.25″, 8.75″ fine spline, 9.25″ front & rear, 7/16″ x 14.

Product Features:

• Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
• 7/8″ x 14 thread

Product Features:

• DANA-60 R/P 3.73 STD MG (USES PRE-LOAD SHIMS)

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Chrysler 8.25″ with 27 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1976 and up Chrysler 8.25″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Product Features:

• Oil baffle for Dana Spicer 60 and Dana Spicer 70U

Standard Open notched cross pin shaft for 9.25″ Chrysler.

Product Features:

• Cross pin shaft
• Fits Chrysler 9.25″
• Standard open carrier only
• Notched

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

8.25″ Chrysler notched cross pin shaft for standard open carriers. (0.801″ diameter). This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers, or with factory Trac Loc positractions.

Product Features:

• Cross pin shaft
• Fits Chryler 8.25″
• 0.801″ diameter
• Notched
• Not compatible with Spartan Lockers or Lock Rights

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Product Features:

• Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Dana Spicer 60 rear
• Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

• Side adjuster for Chrysler 9.25″ rear

Product Features:

• DANA PRELOAD SHIMS (D60 & D70)

Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.

Product Features:

• Side gear thrust washer kit
• Fits Chrysler 8″ and 9.25″

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M88010 race
• All steel construction

9.25″ Chrysler rear cover gasket.

Product Features:

• Cover gasket
• Fits Chrysler 9.25″ rear

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Product Features:

• DANA-60 R/P 3.54 STD MG 24813-5X (USES PRE-LOAD SHIMS)

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Chrysler 9.25″ rear differential. This kit contains carrier bearings and races.

Product Features:

• Fits Chrysler 9.25″ rear
• Includes carrier bearings and races

Product Features:

• STRONG AND DURABLE – Controlled heat treatment process for strength and durability
• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for durability and performance
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• Professional technicians know they can depend on National

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Differential

Product Features:

• Fits Chrysler 9.25″ rear with open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Yukon 1541H alloy 5 lug rear axle for ’85 to ’96 Chrysler 8.25″ van with a length of 32-5/8 inches and 27 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

• Fits 1985-1996 Chrysler van
• 27 spline
• 32 5/8″ long
• 5 x 5.5″ bolt pattern