Name: Remanufactured Brake Master Cylinder
Brand: Wearever
SKU: 11-2872
Price: 217.99 USD

from

$217.99

Using advanced re-engineering materials and processes, our master cylinders match O.E. performance and fitment. New O.E.-quality seals and cups are installed on each unit, ensuring leak-free, long-lasting performance. Cast-iron master cylinders are treate

Product Features:

Only new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Bleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Bores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Cast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Piston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Plastic reservoirs are vacuum-tested to ensure they are leak free.

from

$335.21

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

Short closing paths
Low volume uptake
High efficiency
Low throttling / after-suction resistance
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS
Compact design – ideal for installation in small spaces
Reduced weight – by roughly 20% compared to conventional central valve technology
Fewer components – almost half as many as compared to conventional technologies
Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
Low volume uptake – minimized elastic deformations due to smaller seals
Sealing cups supported in the housing – robustness against soiling and wear; longer life
Cr6-free surfaces for vehicles built from July 2007 (as required by law)

from

$20.79

This automotive brake hydraulic hose was precision-engineered to match the fit, function and performance of the original brake hose on specific vehicles and positions to ensure safe, long-lasting durability as part of a complete brake repair.

Product Features:

Ideal replacement – precision-engineered to match the performance of the original brake hose on specific vehicles
Position-specific – manufactured to precise measurements to provide an exact fit and easy installation
Quality assured – materials tested to exacting government-regulated safety and durability standards
Durable design – made with EPDM rubber and specially coated, corrosion-resistant fittings

from

$20.29

This automotive brake hydraulic hose was precision-engineered to match the fit, function and performance of the original brake hose on specific vehicles and positions to ensure safe, long-lasting durability as part of a complete brake repair.

Product Features:

Ideal replacement – precision-engineered to match the performance of the original brake hose on specific vehicles
Position-specific – manufactured to precise measurements to provide an exact fit and easy installation
Quality assured – materials tested to exacting government-regulated safety and durability standards
Durable design – made with EPDM rubber and specially coated, corrosion-resistant fittings

from

$59.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$66.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$25.49

This disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles
Ideal solution – this kit provides is a reliable replacement for original hardware that has stripped
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.49

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. Caliper Guide Pins are important to replace because they hold the brake piston in place to create effective stopping performance.

Product Features:

This part matches Original Equipment (OE) quality specifications
Easy and fast replacement
Helps deliver a quieter, more efficient braking system
Corrosion resistant coating for long-lasting durability against harsh roads
Manufactured with quality materials to suppress high stress levels

from

$11.56

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$6.79

Brakes are designed as a system and all the parts need to work together for best performance. The boot and square cut seals included in our Caliper Repair Kit, ensure that the caliper works as designed during the apply and release cycle.

Product Features:

This part matches Original Equipment (OE) quality specifications
Increases the life span of the brake pads
Restores brakes to like-new performance
Prevents noise and premature wear
Direct replacement for a proper fit

from

$15.29

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. A complete brake job that includes new hardware goes a long way toward preventing comebacks. Changing out your Rubber Pin Boot or Slider Bushing Kit will ensure the guide pins are clean and free from debris for smoother braking.

Product Features:

This part matches Original Equipment (OE) quality specifications
Easy and fast replacement
Prevents noise and premature wear
Provides longer brake life and performance

from

$284.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$244.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$40.99

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

Dependable stopping power
Single layer shim for quiet braking
OE-designed slots and chamfers to reduce noise and vibration
Powder-coated backing plate prevents corrosion

from

$46.99

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Stainless steel hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking
Includes Premium stainless-steel hardware for easy installation

from

$19.99

Carquest Wearever Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

Application-specific formulations designed for extended pad life and clean wheels
Multi-layer shim for near silent braking
OE designed slots and chamfers for consistent performance
Hardware included on popular and late-model applications

from

$119.15

Ferodo brake products are specified by the world’s leading vehicle manufacturers and are used by many of the top names in motorsports. The Ferodo product range of brake pads provides some of the most advanced performance braking materials available. With Teves brake system with out Hardware

from

$61.99

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking
Includes Premium hardware for easy installation

from

$38.99

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

Dependable stopping power
Single layer shim for quiet braking
OE-designed slots and chamfers to reduce noise and vibration
Powder-coated backing plate prevents corrosion

from

$37.99

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

Dependable stopping power
Single layer shim for quiet braking
OE-designed slots and chamfers to reduce noise and vibration
Powder-coated backing plate prevents corrosion

from

$13.99

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

This part matches Original Equipment (OE) quality specifications
Exact fitment and original replacement
New Brake Hardware prevents premature wear and maximizes performance
Helps deliver a quieter, more efficient braking system

from

$16.79

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

This part matches Original Equipment (OE) quality specifications
Exact fitment and original replacement
Helps deliver a quieter, more efficient braking system
Low-friction PTFE coating to reduce drag
Manufactured with quality materials to suppress high stress levels

from

$5.79

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

This part matches Original Equipment (OE) quality specifications
Exact fitment and original replacement
Helps deliver a quieter, more efficient braking system
Low-friction PTFE coating to reduce drag
Manufactured with quality materials to suppress high stress levels

from

$87.99

Carquest Wearever rotors meet or exceed original equipment specifications while delivering superior stopping power. Carquest Wearever rotors are manufactured with proper harmonic design and non-directional finish that eliminate noise and enhance pedal feel. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of your pads and rotors. Carquest Wearever rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to prevent warping
Air gap eliminates brake fade and increases pad life
Non-Directional finish decreases break-in time

from

$92.74

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$547.19

1 Set = 2 Brake Discs The Eurospare brand cross drilled brake disc set guarantees the same quality fit and performance of the original equipment it replaces. The Cross-Drilled Style Rotors will operate at a slightly cooler temperature than the slotted style because of the added air surface created by the drill pattern.

Product Features:

OEM Quality Direct fit Application.
Made of special cast iron with high carbon content.
Cross Drilled design prevents the formation of a film of water on the disc surface in case of rain.
Resistant to vibrations and noise.
Guarantees the same performance and quality provided by the vehicle manufacturer.
Guarantees OEM quality, performance, durability and fit.

from

$126.72

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning