1995 GMC C1500 Camshafts

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Value-priced seal meets all cataloged application requirements.

“Edelbrock Rollin’ Thunder Camshaft No: 2210 is designed for small-block Chevy engines from 1957-86 and produce optimum torque from the low-end to the mid-range. Rollin’ Thunder camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. They are smooth idling cams for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 440HP and 425 Ft Lbs of Torque when paired with Pro-Flo XT EFI system No: 3528 and RPM E-Tec cylinder heads No: 60975. Must be used with thrust button, high stall torque converter, and stock ratio rocker arms only. Camshaft specifications: – Intake duration: 262 Degrees – Exhaust duration: 266 Degrees – Intake lift: .628″” – Exhaust lift: .608″” – Lobe separation: 114 Degree – Intake Center Line: 109 Degree – Vacuum: 13″””

Mild performance for TPI. Strong low to mid-range power. Requires custom tuning.

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Magnum: High performance. Biggest cam with stock converter but better with 2000+ stall. Use lower gears. Mild rough idle.

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Mr. Gasket cam locking plates feature a steel retainer plate designed to secure the cam gear bolts from coming loose and backing out, preventing costly engine damage. Retainer plate fits under bolt heads allowing tabs to be bent against hex head flats creating a secure positive lock.

Make better electrical repairs and accessory installations with this versatile and durable pigtail connector. It allows quick circuit disconnections for service, and is engineered for reliable performance.

Edelbrock part No: 97385 high performance hydraulic roller lifters for 1987 and later small-block Chevys are the perfect match for Edelbrock Rollin’ Thunder hydraulic roller cams. They are a drop-in replacement for 1987 and later blocks that accept factory roller camshafts. These precision hydraulic roller lifters feature tight ID tolerances that allow for better control at higher RPM and a micro finish OD for reduced friction.

Competition Cams Reduced Travel OE-Style Hydraulic Roller Lifter for ’87+ SBC, LT/LS and V6, 875-1.

Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

This engine expansion plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

This engine expansion plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

This engine expansion plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

This engine camshaft plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Replacement Hex-A-Just Billet Steel Camshaft Dowel Eccentric Bushing; 100% USA Made; Meets or exceeds OEM performance requirements; Cloyes utilizes the latest in design and material technology, ensuring quiet and maintenance-free experience.

Made In USA. 4 oz. Melling engine assembly lube, MELL-LUBE, is formulated to be an initial lubricant on camshaft metal surfaces as well as related valve train parts. The added zinc material (1400 ppm) provides MELL-LUBE with added protection to prevent scoring and galling during initial engine start-up for both newly rebuilt and / or remanufactured engines. In addition, MELL-LUBE contains corrosion inhibitors to prevent rust and pitting of components. MELL-LUBE mixes with any engine oil and will not clog filters. Melling recommends MELL-LUBE be a part of every camshaft install.